Furniture of America YNJ-20805C1 Andoval 59.06 Inch Black Floating TV Stand Instruction Manual
- June 12, 2024
- Furniture of America
Table of Contents
YNJ-20805C1 Andoval 59.06 Inch Black
Floating TV Stand
Instruction Manual
TOOLS REQUIRED
| |
---|---|---
Phillips Screwdriver (Not Included)| Hammer (Not Included)| 2 – People
Recommended
ASSEMBLY RATING
EASY → DIFFICULT
The Assembly Rating is a 5-point system showing the level of effort needed to
assemble a specific product.
CHECK BEFORE STARTING
- Are you missing anything? Double-check all parts, hardware and accessories listed are all accounted for.
- Should we send any replacements? Are there any irregularities or flaws in the parts? We can send replacements!
- Check out our Quick Tips! We recommend reviewing the pre-assembly handouts. Even experts need a refresher now and then!
- Prep Time! Please review the assembly instructions and all diagrams prior to assembling. Arrange parts as recommended on Page 7 and group identical hardware together to make assembling easier.
PRE ASSEMBLY INTRODUCTION
We understand building ready-to-assemble furniture can be a challenging
experience for some. To help avoid confusion, we have provided some helpful
tips that may speed up the process.
Teamwork
ALWAYS have at least two people to help with transporting and assembling the
product to avoid potential injury and/or damage.
 Suitable
Location
Assembling near the area of the intended location is highly recommended.
 Sufficient
Space
Make sure you have enough space to move around during the assembly.
 Avoid
Scratches
Use cardboard, blankets or a carpeted area while assembling furniture to prevent scratches.
 Flat
Surface
Make sure the furniture rests on a flat and level surface with each leg evenly touching the floor.
ASSEMBLY AND CARE ADVICE
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND ‘OR PROPERTY
DAMAGE.
Position each part correctly and insert screws or bolts into their respective
holes.
Turn clockwise to tighten and only tighten when step is completed or when
instructed to do so. Use the appropriate hand tools or power tools for
assembly. Select steps, such as tightening screws and/or bolts, may require
hand tools to avoid causing damage during assembly.
Save the
instructions and store any supplied tools for later maintenance.
After two
weeks, check and tighten any loose hardware and repeat again every six months
thereafter. IT IS THE USER’S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE
HARDWARE MAY LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND
UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND
MAY CAUSE SERIOUS INJURY.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
Note: Every cam lock bolt must have a cam lock connector in order to
fasten the parts together.
- Screw the cam bolt into panel.
- Insert the cam bolt into the bolt hole of joint panel.
- Align the cam lock with its side opening (or arrow) pointing to cam bolt.
- Turn the cam lock clockwise gently until it will not turn any more.
FLOATING TV CONSOLE
- Please keep instructions for future reference.
- Check the quantity and irregularity of parts and hardware before you start.
PARTS
HARDWARE
ACCESSORIES
GET READY
Please group boards as below.
ASSEMBLY INSTRUCTIONS
ASSEMBLY COMPLETED
Please ensure the furniture rests on an even and flat surface. If the produst wobbles or feels loose.double-check all bolts and/or screws are properly tightened and secured
Keep this handy!
Please retain this instruction manual and any order-related information for future reference.
Lift, don’t drag!
To avoid damage to product please always LIFT the product when transporting of adjusting the placement.
Wall Mounting and Fixing
EXPANSION WALL ANCHOR
Our provided expansion wall anchors are only suitable for masonry walls, such as drywall, plaster or concrete, and are best for holding lightweight items or for anti-tip prevention. If you are unsure of the correct wall anchor to use with the product, please request professional guidance. liability for product damage or failure due to using the incorrect anchors will fall on the installer.
CHECK BEFORE PROCEEDING
Prior to drilling or hammering, please check for wires or pipes. We recommend using a stud finder to locate a stud, which will offer more appropriate resistance and hold more weight.
QUICK TIPS
- If unsure of the proper size, always choose a larger screw and wall anchor.
- Match the drill bit to the wall anchor and hole size.
- Only drill horizontally. Do not force the drill or enlarge the hole for the wall anchor.
- Take extra care when drilling into high walls or ceramic tiles. Wall anchors should be a tight fit for the hole. Never use wall anchors in ceilings.
MAINTENANCE
We recommend a yearly check to see if the wall anchor or screw has loosened.
If so, please remove the existing wall anchor and screw, and use a new anchor.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>