Furniture of America IDF-7319WN-C-K Olala 5-Drawer Light Walnut Instruction Manual
- June 12, 2024
- Furniture of America
Table of Contents
**Furniture of America IDF-7319WN-C-K Olala 5-Drawer Light Walnut Instruction Manual
**
TOOLS REQUIRED
-
Phillips Screwdriver (Not Included)
-
2 – People Recommended
-
ASSEMBLY RATING
The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
CHECK BEFORE STARTING
Are you missing anything?
Double-check all parts, hardware and accessories listed are all acccounted
for.
Should we send any replacements?
Are there any irregularities or flaws in the parts? We can send replacements!
Check out our Quick Tips!
We recommend reviewing the pre-assembly handouts. Even experts need a
refresher now and then!
Prep Time!
Please review the assembly instructions and all diagrams prior to assembling.
PRE ASSEMBLY INTRODUCTION
We understand building ready-to-assemble furniture can be a challenging experience for some. To help avoid confusion, we have provided some helpful tips that may speed up the process.
Teamwork
ALWAYS have at least two people to help with transporting and assembling the
product to avoid potential injury and/or damage.
Suitable Location
Assembling near the area of the intended location is highly recommended.
Sufficient Space
Make sure you have enough E space to move around during the assembly.
Avoid Scratches
Use cardboard, blankets or a carpeted area while assembling furniture to
prevent to prevent scratches and damages.
Flat Surface
Make sure the furniture rests on a flat and level surface with each leg evenly
touching the floor.
ASSEMBLY AND CARE ADVICE
FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE.
Position each part correctly and insert screws or bolts into their respective holes.
Turn clockwise to tighten and only tighten when step is completed or when
instructed to do so.
Use the appropriate hand tools or power tools for assembly. Select steps, such
as tightening screws and/or bolts, may require hand tools to avoid causing
damage during assembly.
Save the instructions and store any supplied tools for later maintenance.
After two weeks, check and tighten any loose hardware and repeat again every
six months thereafter.
IT IS THE USER’S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.
CHEST
- Please keep instructions for future reference.
- Check the quantity and irregularity of parts and hardware before you start.
PARTS
1 pc
Chest
HARDWARE
(TA) 1set
Anti-dumping hardware kit
ASSEMBLY INSTRUCTIONS
Part #1) x 1pc Hardware #A) x 1set
Remove handles from within the drawers and attach to the front.
ASSEMBLY COMPLETED
Please ensure the furniture rests on an even and flat surface. If the product wobbles or feels Ioose, double check all bolts and/or serews are properly tightened and secured.
Keep this handy!
Please relain this instruction manual and any order-related information for
future reference.
Lift, don’t drag!
To avoid damage to product please aluays LIFT the produot when transporting of
adjusting the placement.
ASSEMBLY INSTRUCTIONS
Wall Mounting and Fix
EXPANSION WALL ANCHOR
Our provided expansion wall anchors are only suitable for masonry walls, such
as drywall, plaster or concrete, and are best for holding lightweight items or
for anti-tip prevention. If you wall anchor to use with the product, please
request professional guidance. Liability for product damage or failure due to
using the incorrect anchors ) are unsure of the correct will fall on the
installer.
CHECK BEFORE PROCEEDING
Prior to drilling or hammering, please check for wires or pipes. We recommend
using a stud finder to locate a stud, which will offer more appropriate
resistance and hold more weight.
QUICK TIPS
-
If unsure of the proper size, always choose a larger screw and anchor.
-
Match the drill bit to the wall anchor and hole mm:/ size.
-
Only drill horizontally. Do not force the drill or enlarge the hole for the wall anchor.
-
Make extra care when drilling into high walls or ceramic tiles. Wall anchors should be a tight fit for the hole. Never use wall anchors in ceiling
MAINTENANCE
We recommend a yearly check to see if the wall anchor or screw has loosened. If so, please remove the existing wall anchor and screw, and use a new anchor.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>