Furniture of America IDF-DK935 Vickersen White Make Up Vanity Table With Tilting Mirror Instruction Manual

ASSEMBLY
INSTRUCTIONS 

TOOLS REQUIRED

ASSEMBLY RATING

The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
CHECK BEFORE STARTING

▢ Are you missing anything?
Double-check all parts, hardware and accessories listed are all acccounted for.
▢ Should we send any replacements?
Are there any irregularities or flaws in the parts? We can send replacements!
▢ Check out our Quick Tips!
We recommend reviewing the pre-assembly handouts. Even experts need a refresher now and then!
▢ Prep Time!
Please review the assembly instructions and all diagrams prior to assembling.

PRE ASSEMBLY INTRODUCTION

We understand building ready-to-assemble furniture can be a challenging experience for some. To help avoid confusion, we have provided some helpful tips that may speed up the process.

Teamwork
ALWAYS have at least two people to help with transporting and assembling the product to avoid potential injury and/or damage.

Suitable Location
Assembling near the area of the intended location is highly recommended.

Sufficient Space
Make sure you have enough space to move around during the assembly.

Avoid Scratches
Use cardboard, blankets or a carpeted area while assembling furniture to prevent to prevent scratches and damages.

Flat Surface
Make sure the furniture rests on  a flat and level surface with each leg evenly touching the floor.

ASSEMBLY AND CARE ADVICE

FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE.
Position each part correctly and insert screws or bolts into their respective holes.

Save the instructions and store any supplied tools for later maintenance.

Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly.

Turn clockwise to tighten and  only tighten when step iscompleted or when instructed to do so.

After two weeks, check and tighten any loose hardware and repeat again every six months thereafter.

IT IS THE USER’S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE HARDWARE MAY LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE SERIOUS INJURY.

CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS

Note :
Every cam lock bolt must have a cam lock connector in order to fasten the parts together.

1. Screw the cam bolt into panel.
2. Insert the cam bolt into the bolt hole of joint panel.
3. Align the cam lock with its side opening (or arrow) pointing to cam bolt.
4. Turn the cam lock clockwise gently until it will not turn any more.

VANITY SET

PARTS

HARDWARE

Exploded View

ASSEMBLY INSTRUCTIONS

1. Part #1 x1pc
   Part #2pc
   Hardwa re#J x2 prcs

2. Part #5 x1pc
   Hardware #E x2pcs
   Hardware#K x1pc
   Attach Wood Dowel (#E) to Left Side Plate (#1). Insert Cam Lock (#K) unto Upper Horizontal (#5). Attach Upper Horizontal (#5) to Left Side Plate (#1)

3. Part #3 x1pc
   Hardwa re#A x4pcs
   Hardwa re#C x4pes
   Hardwa re#D x4pes
   Hardwa re#E X2pcs
   Attach Laminate (#3) unto Left Side Plate (#1) and secure by using Bolt (#A) with Washers (#C, D) and Wood Dowels (#E)

4. Part #4 x1pc
   Hardware#A x2pcs
   Hardware#C x2pcs
   Hardware #D x2pcs
   Align and attach Back Plate (#4) by using Bolt (#A) with Washers (#C, D)

5. Hardware #A xBpes
   Hardware #C xBpes
   Hardware#D x6pcs
   Hardware#E xdpcs
   Hardware#K x1pcInsert Cam Lock (#K) and Wood Dowels (#E) unto Upper Horizontal (#5). Align and attach Right Side Plate (#2) by using Bolt (#A) with Washers (#C, D).

6. Part #7 x1pe
   Part #8 x2pcs
   Hardware #B x2pes
   Hardware#C x2pcs
   Hardware#D x2pcs
   Hardware#E x4pes
   Align and attach Mirror Base (#7) and Mirror Pole (#8) using Bolt (#B) with Washers (#C, D) and Wood Dowels (#E)

7. Part #9 x1pc
   Hardware # L X2pcsAttach Mirror (#9) and secure using Mirror Bolt (#L)

8. Hardware#G x1pc
   Hardwa re#H x1pcAttach Block Drawers (#G)\with Screw (#H)

9. Part #6 x1pc Align and insert Box (#6). Affix Handle as shown

10. Part#109 xipe
    Hardware#I X2pes Align and attach Glass (#10) using Glass Suction Cups (#l)

11. Hardware#M x3pcsAttach Light Bulbs (#M) as shown

12. Hardware#N x1set

ASSEMBLY COMPLETED
Please ensure the furniture rests on an even and flat surface. If the product wobbles or feels loose, double-check all bolts and/or screws are properly tightened and secured.
Keep this handy!
Please retain this instruction manual and any order-related information for future reference.
Lift, don’t drag!
To avoid damage to product ploase always LIFT the product when transporting of adjusting the placement.
Wall Mounting and Fixing
EXPANSION WALL ANCHOR
Our provided expansion wall anchors are only suitable for masonry walls, such as drywall, plaster or concrete, and are best for holding lightweight items or for anti-tip prevention. If you are unsure of the correct wall anchor to use with the product, please request professional guidance.liability for product damage or failure due to using the incorrect anchors will fall on the installer.
CHECK BEFORE PROCEEDING
Prior to drilling or hammering, please check for wires or pipes. We recommend using a stud finder to locate a stud, which will offer more appropriate resistance and hold more weight.

QUICK TIPS

1. unsure of the proper size, always choose a larger screw and wall anchor.

2.  Match the drill bit to the wall anchor and hole size.

3.  Only drill horizontally. Do not force the drill or enlarge the hole for the wall anchor.
   

4. Take extra care when drilling into high walls or ceramic tiles. Wall anchors should be a tight fit for the hole. Never use wall anchors in ceilings.

MAINTENANCE

We recommend a yearly check to see if the wall anchor or screw has loosened. If so, please remove the existing wall anchor and screw, and use a new anchor.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>