Woods MDX20P Dehumidifier with Pump Instruction Manual
- June 15, 2024
- Woods
Table of Contents
Woods MDX20P Dehumidifier with Pump
Product Information
Specifications
- Model: MDX20, MDX20P, MDX25, MDX25P
- Revision Date: 14-11-2023
- Manufacturer: Wood’s
- Website: woods.se
Product Usage Instructions
Safety Instructions
Before installing and using the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use cause injuries and damages. Always keep the instructions with the appliance for future reference.
Children and Vulnerable People’s Safety
WARNING: Risk of injury or permanent disability. This appliance can be used by children aged eight years and above, persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance safely and understand the hazards involved. Do not let children play with the appliance. Children of less than three years should be kept away unless continuously supervised. Keep all packaging away from children. Cleaning and user maintenance shall not be done by children without supervision.
General Safety
This appliance is intended to be used in households and similar environments
such as basements, crawl spaces, staff kitchen areas in shops, offices, and
other working environments. Keep ventilation openings clear of obstruction.
Installation Instructions
WARNING: Only a qualified person can install this appliance.
Make sure air can circulate around the appliance. Wait at least 4 hours before
connecting the appliance to the power outlet. This is to allow the oil to flow
back into the compressor. Do not install the appliance close to radiators or
other heat sources. Do not install the appliance in direct sunlight.
Usage Instructions
WARNING: Risk of injury, burns, electrical shock, or fire. Do not change the specification of this appliance. Be careful not to cause damage to the refrigerant circuit. It contains propane (R290), a natural gas with a high level of environmental compatibility. This gas is flammable. If damage occurs to the refrigerant circuit, make sure that there are no flames and sources of ignition in the room. Ventilate the room. Do not put flammable products or wet items with flammable products near or on the appliance.
Disposal Instructions
WARNING: Risk of injury. Disconnect the appliance from the mains supply. Cut off the mains cable and discard it. The refrigerant circuit of this appliance is ozone-friendly. Contact your local authority for information on how to discard the appliance correctly. Do not cause damage to the part of the cooling unit that is near the heat exchanger.
Electrical Connection
WARNING: Risk of fire and electrical shock. The appliance must be connected to a grounded outlet. Ensure that the electrical information on the rating label is in accordance with local regulations.
Frequently Asked Questions (FAQ)
Q: Can children use this dehumidifier?
A: This dehumidifier can be used by children aged eight years and above,
provided they have been given supervision or instruction concerning its safe
use and understand the hazards involved. Children under three years should be
kept away unless continuously supervised.
Q: Can I change the specifications of the appliance?
A: No, it is not recommended to change the specifications of the
appliance. Altering the appliance may cause damage to the refrigerant circuit,
which contains flammable gas. It is important to use the appliance as intended
to ensure safety.
Q: How should I dispose of the appliance?
A: To dispose of the appliance correctly, disconnect it from the mains
supply, cut off the mains cable, and contact your local authority for
information on proper disposal methods. Take care not to cause damage to the
cooling unit near the heat exchanger during disposal.
Revision date: 14-11-2023
Scan the QR-code or visit woods.se for the latest updated user manual.
Safety Instructions
FLAMMABLE MATERIAL.
This appliance contains R290/Propane, a flammable refrigerant.
Refer operator’s manual.
Read technical manual.
Read the operator’s manual.
SAFETY INFORMATION
Before installing and using the appliance, carefully read the supplied
instructions. The manufacturer is not responsible if an incorrect installation
and use cause injuries and damages.
Always keep the instructions with the appliance for future reference.
CHILDREN AND VULNERABLE PEOPLE’S SAFETY
WARNING
Risk of injury or permanent disability.
This appliance can be used by children aged eight years and above, persons
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge if they have been given supervision or instruction concerning
the use of the appliance safely and understand the hazards involved. Do not
let children play with the appliance.
Children of less than three years should be kept away unless continuously
supervised.
Keep all packaging away from children. Cleaning and user maintenance shall not
be done by children without supervision.
GENERAL SAFETY
This appliance is intended to be used in households and similar environments
such as basements,crawl spaces, staff kitchen areas in shops, offices and
other working environments. Keep ventilation openings clear of obstruction.
Other than those recommended by the manufacturer, do not use mechanical
devices or other means to accelerate the defrosting process.
The appliance shall not be stored in a room where ignition sources are
operating continuously (open flames,working gas appliance, operation electric
heater, etc.). Do not pierce or burn. Be aware that refrigerants may not have
an odour. Do not use water spray and steam to clean the appliance. Clean the
appliance with a moist, soft cloth. Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,solvents or metal objects. If the
power cord is damaged, it must be replaced by the manufacturer, its authorized
Service Centre or similarly qualified persons to avoid a hazard.
WARNING
Only a qualified person can install this appliance.
Remove all packaging material. Do not install or use a damaged appliance.
The appliance shall be installed, operated and stored in a room with a floor
area larger than 3m². Strictly follow the installation instruction supplied
with the appliance. Always be careful when you move the appliance because it
is heavy. Always wear safety gloves.
Make sure air can circulate around the appliance. Wait at least 4 hours before connecting the appliance to the power outlet. This is to allow the oil to flow back into the compressor. Do not install the appliance close to radiators or other heat sources. Do not install the appliance in direct sunlight.
ELECTRICAL CONNECTION
WARNING
Risk of fire and electrical shock.
The appliance must be connected to a grounded outlet. Ensure that the
electrical information on the rating label is in accordance with the power
supply. If not, contact an electrician. Always use a correctly installed
shockproof socket. Do not use multi-plug adapters and extension cables. Make
sure not to cause damage to the electrical components (e.g. plug, cable).
Contact the authorized Service Centre or an electrician to change the
electrical components. The cable must stay below the level of the plug.
Connect the plug to the power socket only at the end of the installation. Make
sure that there is access to the plug after the installation. Do not pull the
power cable to disconnect the appliance.
Always unplug the power cable from the plug only.
USE
WARNING
Risk of injury, burns, electrical shock or fire.
Do not change the specification of this appliance. Be careful not to cause
damage to the refrigerant circuit. It contains propane (R290), a natural gas
with a high level of environmental compatibility. This gas is flammable.
If damage occurs to the refrigerant circuit, make sure that there are no
flames and sources of ignition in the room. Ventilate the room. Do not put
flammable products or wet items with flammable products near or on the
appliance.
DISPOSAL
WARNING
Risk of injury.
Disconnect the appliance from the mains supply. Cut off the mains cable and
discard it. The refrigerant circuit of this appliance is ozone-friendly.
Contact your local authority for information on how to discard the appliance
correctly. Do not cause damage to the part of the cooling unit that is near
the heat exchanger.
Operating Instructions
Thank you for your purchase and trust in Wood’s.
Please read the instructions below on operating
and caring for your Wood’s product.
PRODUCT PARTS (REFER IMAGE A, PAGE 2–3)
- Top cover
- Vent
- Front shell
- Chassis
- Wheels
- Control panel
- Back shell
- Filter
- Water tank
- Drain port
CONTROL PANEL
Power button (6): After the power is turned on,the indicator light is green
and is on for a long time.
Mode button (5): Press the “Mode” button. There are three working modes:
dehumidify mode (DEH), fan mode (FAN), and (DRY) dry mode.
Down button (4): Click to adjust the set humidity level or timing time. Press
and hold the button for 3 seconds to select the mould removal function, and
the “DRY INSIDE” light will be on. This function can only be turned on when
the machine is turned on. If this function is turned on and the machine is
turned off later, the fan motor will be turned off after a delay of 5 minutes.
(During the delay shutdown process, except for the power indicator, other
indicators are turned off). This feature is turned off by default.
Up button (3): Click the button to adjust the set humidity or timing time
upwards.
Fan speed button (2): Press the fan speed button to select the fan speed.
“HIGH” for high speed and “LOW” for low speed. Press and hold the fan speed
button for three seconds to turn off or turn on the triangular display on the
front face. When the hidden digital display is turned off, the display board
digital tube and indicator light have a dark display function. If there is no
operation for 5s, it will enter the dark display state.
Timer button (1): Press the timing key to set timing/query timing/cancel
timing.
Child lock function (1) + (2): Press this group of keys to enable or disable
the child lock “LOCK” function.
MODEL WITHOUT PUMP
Ambient temperature (3) + (4): Press this group of keys and the ambient
temperature can be showed.
Ambient temperature (1) + (3): Press this group of keys and the ambient
temperature can be monitored.
Check filter indicator (1) + (4): Press this group of keys and the “CHECK
FILTER” indicator light can be turned off, and the timing of the filter
cleaning prompts to restart the timing.
Water pump function (3) + (4): By pressing these keys simultaneously, the
automatic drainage “AUTO DRAIN” function of the pump can be turned on or off.
- Plug in the power plug. Please pay attention to ensure that the machine’s power supply is consistent with the power grid.
- Please press both sides of the swing to manually adjust the swing leaf to the desired angle.
WORKING MODE
Dehumidify Mode (DEH):
-
A. The Compressor will start when the humidity level is higher than 3% of set level, during which time, the fan will run at the set wind speed. When the humidity level falls to 3% from the set level, the compressor will automatically turn off and the fan will blow on low speed. (The fan speed can be adjusted at this time).
-
B. Display the set humidity (CO-35-85%RH):
Press the up and down adjustment keys to adjust the desired humidity. -
C. The fan speed is adjustable. “HIGH” for high speed and “LOW” for low speed.
-
D. Child lock and timer functions can be set.
-
E. MODEL WITHOUT PUMP ONLY: When the ambient humidity does not reach the set humidity, the red indicator light of the “OK” light on the display panel is off. When the ambient humidity reaches the set humidity, the “OK” light on the display panel will light up in red.
-
F. The triangular hidden display on the front shell displays three colours according to the humidity.
It shows red when the relative humidity is higher than 65%, green when the relative humidity is between 45% and 65%, and blue when the relative humidity is below 45%. -
G. When the set humidity is “CO”, the compressor runs continuously without limiting the set humidity, and the fan speed is adjustable. Also, when the CO is displayed, the child lock and timer can be set.
Fan Mode (FAN):
When entering the air supply mode through the mode conversion, the compressor
will not work; the default is low wind, the fan speed is adjustable, and the
ambient humidity (30~90%RH) is displayed.
Dry Mode (DRY):
Entering the “dry mode” will run a fixed, continuous high airflow no matter
the humidity level.
TIMER FUNCTION “TIMER”
- A. Press the timing key to start the timing function, and you can set the timing/query timing/ cancel the timing.
- B. In the non-timed state: press the “timing” key (1, refer image F, page 2-3) to enter the timing setting state, the timing indicator light is on, and the digital tube flashes (5 times, 1 time/second) to display the timing time during the blinking period, press the “up or down” key to set Timing time between (0~24), the selected time will be confirmed after it flashes five times (or if there are other valid key operations during the flashing period, it will be confirmed immediately).
- C. In the timing state: press the “timing” key (1, refer image F, page 2-3) to enter the timing query state, the digital tube flashes (5 times, 1 time/ second) to display the timing time, and press the “timing” key (1, refer image F, page 2-3) again during the digital flashing period to cancel the timing.
- D. During the timing period, the “TIMER” indicator light is on. After the timing is over, the timing indicator will turn off.
- E. The current on/off state will not be changed when setting the timing on/off; the setting of the timing function is only valid for the last time and only once. The on/off operation caused by a key press will clear all timing settings.
CHILD LOCK FUNCTION “LOCK”
Press the “1” + “2” keys (refer image F, page 2-3) at the same time to turn on
the child lock function, the child lock indicator light “LOCK” is on, and all
key operations are invalid; press this group of composite keys again to turn
off the child lock function, and the child lock indicator light is off.
WATER FULL ALARM FUNCTION “FULL”
When the “water full” signal is detected for 5 seconds (the water level switch
is disconnected), the machine will be turned off, the buzzer will sound five
alarms, the water full indicator light “FULL” will be on, and the digital tube
will flash to display “FL” until the water is removed.
FILTER CLEANING REMINDER FUNCTION “CHECK FILTER” (MODEL WITH PUMP ONLY),
After the machine has been running for 250 hours in total, the filter cleaning
indicator “CHECK FILTER” lights up, reminding to clean the water pump inlet
filter (refer image C, page 2-3) and the unit air inlet filter (refer image E,
page 2-3). After cleaning, press the (1) + (4) keys (refer image F, page 2-3)
to reset the filter reminder, the indicator light will turn off, and the
timing cleaning reminder will restart.
AUTOMATIC DRAIN FUNCTION “AUTO DRAIN” (MODEL WITH PUMP ONLY)
Press (3) + (4) keys (refer image F, page 2-3) simultaneously to turn on the
automatic drainage function of the water pump, and the drainage indicator
light “AUTO DRAIN” will be on. When it is detected that the water is full, the
water pump enters the automatic drainage program.
NOTE! The water is drained when the container is full. When the unit detects that the container is full, the pump is activated and the water is drained in approximately 45 minutes.
DRAINAGE INSTRUCTIONS
(MODEL WITHOUT PUMP)
USE OF WATER TANK (REFER IMAGE C,PAGE 2-3):
- When the water tank is full, the machine automatically stops running, the water full indicator “FULL” light is on, and the LED digital screen flashes “FL” and sounds an alarm five times.
- Put your hand on the depression at the bottom of the water tank, gently take out the water tank, tilt the water tank and pour out the water in the water tank from the drain port.
- Push the water tank back to the correct position, then turn on the dehumidifier.
Note: Please empty the water in the water tank.
Before putting the water tank into the body,please confirm that the water
tank’s cover and tank are installed tightly and that the handle is put back in
its original position. Then, gently push the water tank into the correct
position with both hands.
CONTINUOUS DRAINAGE METHOD
(REFER IMAGE B, PAGE 2-3):
If you don’t want to pour the water in the water tank frequently, you can
connect a drain hose (the inner diameter of the hose is 10mm) behind the
machine to drain the water.
- Find the location of the drain at the back.
- Use a suitable drain hose length to firmly connect it to the drain port.
- Before use, please carefully check and ensure that the water hoses are connected firmly to prevent water from leaking.
(MODEL WITH PUMP ONLY)
USE OF WATER TANK (REFER IMAGE C, PAGE 2-3):
- Before removing the water tank, please press the power button to turn it off.
- Put your hand on the depression at the bottom of the water tank, gently take out the water tank, tilt the water tank and pour out the water in the water tank from the drain port.
- Put the water intake pipe into the water tank as shown in the picture, then push the water tank back to the correct position and turn on the dehumidifier again.
Note: After emptying the water tank and before putting the water tank into the machine, please confirm that the water tank’s cover and tank are installed tightly and that the handle is returned to its original position. Then gently push the water tank into the correct position with both hands.
- Please pay attention to whether the water intake hose is put into the water tank correctly, and pay attention not to press the water intake hose by the water tank.
CONTINUOUS DRAINAGE METHOD (REFER IMAGE B, PAGE 2-3):
If you don’t want to pour the water from the water tank frequently, you can
connect a drain pipe/ hose (the inner diameter of the hose is 10mm) behind the
machine to drain the water.
Step 1: The first step is to find the location of the drain at the back.
Step 2: Use a suitable drain hose length to firmly connect it to the drain port.
Step 3: Before use, please carefully check and ensure that the water hose is connected firmly to prevent water from leaking.
WATER PUMP FOR AUTO DRAIN “AUTO DRAIN” (REFER IMAGE D, PAGE 2-3):
-
The model with a water pump can also choose the automatic drain “AUTO DRAIN” function.
-
Use a suitable tool to open the hole plugging piece at the position (refer image D, page 2-3).
-
Insert the water hose into the drain port as shown in the figure and connect firmly.
-
Put the other end of the water hose into the floor drain or a large water storage container.
If you use a large water storage container, pay attention to the water level of the container to prevent the water in the container from overflowing. -
Pressing (3) + (4) at the same time (refer image F, page 2-3), the auto drain indicator “AUTO DRAIN” of the pump can be turned on or off.
WARNING: Do not remove the water tank when the auto drain is switched on. If you need to remove the water tank, please press the power button to turn it off. Do not operate in violation of regulations; otherwise, it will cause damage to the components of the unit.
MAINTENANCE
Before maintaining the machine, please turn off the power and pull out the power plug.
-
Clean the surface
Clean the surface of the unit with a soft, damp cloth. Do not use alcohol, gasoline and other chemical solvents; otherwise, the machine or machine’s surface will be damaged. -
Cleaning the filter (refer image E, page 2-3)
Please clean the nylon filter at least once every two weeks, washing with cold or warm water not exceeding 40 degrees. If the filter is not very dirty, simply vacuum the dust off it. Never use a dryer of any kind. Do not use alcohol, gasoline, benzene and other chemical solvents to clean. -
Storage of the machine
After cleaning, please fix the power cord, pack the dehumidifier body in a soft plastic bag, and put the dehumidifier body in a dry place to take dustproof measures and keep it out of the reach of children.
3 YEARS WARRANTY
In order to extend the warranty from 2 to 3 years, please register your
product after your purchase at warranty-woods.com
SAVE YOUR RECEIPTS!
These will be required for any warranty claim during the period.
TECHNICAL SPECIFICATIONS
WOOD’S MODEL NO.
| MDX20 + MDX20P (PUMP)| MDX25 + MDX25P (PUMP)
---|---|---
Capacity| 20L| 25L
Recommended surface (room size)| 20-25 m²| 25-35 m²
Maximum area| 40 m2| 55 m²
Working interval temperature| 5-35°C| 5-35°C
Dehumidifier Capacity
| 26.7°C/60%RH (L/D)| 11 l| 14 l
30°C/80%RH (L/D)| 20 l| 25 l
Rated Input| 360W| 410W
Power at 20°C and 70%RH| 250W| 310W
Power consumption at 20°C and 70%RH| 3kWh/24 h| 4kWh/24 h
Tank volume| 6L| 6L
Number of ventilation speeds| 2| 2
Air flow
| High Speed| 180 m3/h| 180 m3/h
Low Speed| 120 m3/h| 120 m3/h
Sound power| 41-55 dB| 41-55 dB
Type of refrigerant gas| R290/60g| R290/70g
IP-Code| IPX1| IPX1
Washable air filter| YES| YES
Water Pump| Only MDX20P| Only MDX25P
Device dimensions (HxWxD)| 530335260mm| 530335260mm
Net weight
| 13.65kg (MDX20)
14kg (MDX20P)
| 14kg (MDX25)
14,5kg (MDX25P)
Technical changes and improvements may occur. All values are approximate and may vary depending on external circumstances such as temperature, ventilation and humidity.
TROUBLESHOOTING
| PROBLEM | POSSIBLE REASON | SOLUTIONS |
|---|
Hot air
| The dehumidifier’s air passes through the temperature recovery unit, so the hot air is discharged (no cooling function).|
This is not a malfunction.
The dehumidifier is not working
| Is the power plug unplugged?| Insert the power plug into the socket.
Is the tank full? Or is the tank placed in the wrong place?| Drain the
standing water in the tank and put the tank back in the correct position.
Dehumidification function does not work
| Is the temperature or humidity in the room too low?| During the dry season,
the dehumidifying capacity of the dehumidifier will be reduced.
Are the air outlets or air inlets blocked?| Clean up any items that block the
air outlet or air inlet.
No air flow| Is the air filter blocked?| Clean the air filter as above.
Too much noise when the machine is running
| Is it improperly placed so that the machine is tilted or unstable?| Please
prevent the machine from being used on unstable ground.
Is the air filter blocked?| Clean the air filter as above.
Model with pump. After the auto drain function is turned on, the “water full” alert appears
| The water inlet filter of the water pump is clogged, and the drainage is
slow.| After cleaning the water filter, turn on the power again.
The water tank is not installed in place, causing the alert.| Install the
water tank in place and turn on the power again.
The water pump fails and does not drain.| Turn off the power, and then turn on
the power again after overhauling the water pump.
Model with pump. Abnormal working sound of water pump
|
The water inlet hose of the water pump is not placed correctly, and water cannot be obtained.
|
Take out the water tank, put the water inlet management (drain hose) into the bottom of the water tank, and then put the water tank in place.
After the automatic drain function is turned on, remove the water tank.
|
Take out the water tank, put the water inlet management (drain hose) into the bottom of the water tank, and then put the water tank back in place.
Error Codes
| Display “E1”;| Humidity sensor failure.
Display “E2”;| Tube temperature sensor failure: display “E2”;
Display “FL”| Water Full.
DEF. indicator lights up| This is not a malfunction. The machine turns on the
defrosting function, and it will return to normal after a while.
If you have a problem with your dehumidifier, refer to the troubleshooting
guide. If none of the above works, contact your dealer to get your
dehumidifier serviced.
This marking indicates that this product should not be disposed with other household wastes throughout the UK and the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,recycle it responsibly to promote the sustainable reuse of material resources. To return your us device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Register and find the latest updated user manual, usage advice, updated brochures, troubleshooting, and service information at woods.se
CUSTOMER CARE AND SERVICE
Always use original spare parts. When contacting our authorized service
centre, ensure that you have the following data available: Model
number,receipt, and serial number.
Warning / Caution-Safety information. General information and tips.
Environmental information. Subject to change without notice.
Wood’s is marketed and distributed by:
Woods Production Sweden AB Maskingatan 2–4, 441 27 Alingsås, Sweden
info@woods.se +46 (0)31 761 36 10 woods.se
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>