MiBOXER E3-WR 3 In 1 LED Controller Instruction Manual

MiBOXER E3-WR 3 In 1 LED Controller

Product Information

Specifications

• Product Name: Subordinate New Brand 3 in 1 LED Controller (WiFi + 2.4G)
• Features:
  • 16 Million colors to choose from
  • Color temperature adjustable
  • Dim brightness / Saturation
  • 2.4G RF wireless transmission technology
  • WiFi wireless control
  • WiFi support long-range control
  • Auto-transmitting & Synchronization (only for remote control dimming)
  • Device sharing
  • Tap-to-Run & automation
  • Timing setting / countdown turn on / off LED light
  • DMX512 controllable (Only for RGB+CCT output mode DMX512 LED transmitter is needed)
  • Remote control Control distance 30m
  • Smartphone app control
  • Support third party voice control
  • Group control
  • Biorhythm Support music rhythm
  • Sleep / wake up plan
  • Support scene customization
  • Do not disturb mode

Product Usage Instructions

Set up output mode
To set up the correct output mode, follow these steps:

1. Press the SET button continuously to switch the output mode.
   Note: If there is no operation within 3 seconds, the device will log out.

2. Confirm the output mode based on the color of the indicator:

   • Red Light: RGB output mode
   • Green Light: RGBW output mode
   • Blue Light: RGB+CCT output mode

Compatible with these 2.4G RF remote controls (Purchased separately)

• FUT100
• FUT089S FUT089
• FUT088
• FUT092
• FUT096
• B8
• FUT089-B
• FUT092-B FUT096-B
• B0 / B0-B
• B4 / B4-B / T4
• B3 / B3-B / T3
• S2-B / S2-W S2-G
• SET 8.8.8.8
• FUTD01

G RF Remote control instructions

1. Linking Code Instructions

2. Power off for 10 seconds and power on again or short press SET button one time.

3. Short press I button three times within 3 seconds.
   Lights blink three times slowly, indicating successful linking.
   Note : Lights that have already linked cannot be linked again.

4. Unlinking Code Instructions

5. Power off for 10 seconds and power on again or short press SET button one time.

6. Short press I button five times within 3 seconds. Lights blink ten times quickly, indicating successful unlinking.
   Note: Lights that haven’t linked do not need to be unlinked.

7. Auto Transmitting & Synchronization (only for remote control)
   

8. Remote signal auto transmitting: One light can transmit the signals from the remote control to another light within 30m. As long as there is a light within 30m, the remote control distance can be limitless.

9. Dynamic modes auto synchronization: Multiple lights can synchronize if they are in the same dynamic mode and linked with the same remote. The distance between each light should be within 30m.

Dynamic mode table selection (only for remote control)
To select dynamic mode table:

• Select dynamic mode table 1: While the light is in static mode, short press S+ button five times quickly until the blue light flashes three times slowly, indicating successful activation of static mode.
• Select dynamic mode table 2: While the light is in static mode, short press S- button five times quickly until the yellow light flashes three times slowly, indicating successful activation of static mode.

FAQ

Q: What are the features of the Subordinate New Brand 3 in 1 LED Controller?
A: The features of the Subordinate New Brand 3 in 1 LED Controller include:

• 16 Million colors to choose from
• Color temperature adjustable
• Dim brightness / Saturation
• 2.4G RF wireless transmission technology
• WiFi wireless control
• WiFi support long-range control
• Auto-transmitting & Synchronization (only for remote control dimming)
• Device sharing
• Tap-to-Run & automation
• Timing setting / countdown turn on / off LED light
• DMX512 controllable (Only for RGB+CCT output mode DMX512 LED transmitter is needed)
• Remote control Control distance 30m
• Smartphone app control
• Support third party voice control
• Group control
• Biorhythm Support music rhythm
• Sleep / wake up plan
• Support scene customization
• Do not disturb mode

Q: How do I set up the output mode?
A: To set up the output mode, follow these steps:

1. Press the SET button continuously to switch the output mode.
   Note: If there is no operation within 3 seconds, the device will log out.

2. Confirm the output mode based on the color of the indicator:

   • Red Light: RGB output mode
   • Green Light: RGBW output mode
   • Blue Light: RGB+CCT output mode

Q: How do I link and unlink the remote control?
A:

Linking Code Instructions:
Short press I button three times within 3 seconds. Lights blink three times slowly, indicating successful linking.
Note: Lights that have already linked cannot be linked again. Power off for 10 seconds and power on again or short press SET button one time.

Unlinking Code Instructions:

1. Power off for 10 seconds and power on again or short press SET button one time.
2. Short press I button five times within 3 seconds.

Lights blink ten times quickly, indicating successful unlinking.
Note: Lights that haven’t linked do not need to be unlinked.

Q: How does the auto transmitting and synchronization feature work?
A: The auto transmitting feature allows one light to transmit the signals from the remote control to another light within 30m. As long as there is a light within 30m, the remote control distance can be limitless. The synchronization feature allows multiple lights to synchronize if they are in the same dynamic mode and linked with the same remote. The distance between each light should be within 30m.

Q: How do I select the dynamic mode table using the remote control?
A: To select the dynamic mode table, follow these steps:

• Select dynamic mode table 1: While the light is in static mode, short press S+ button five times quickly until the blue light flashes three times slowly, indicating successful activation of static mode.
• Select dynamic mode table 2: While the light is in static mode, short press S- button five times quickly until the yellow light flashes three times slowly, indicating successful activation of static mode.

3 in 1 LED Controller (WiFi + 2.4G) Instruction Manual

Product features

• This product uses WiFi + Bluetooth + 2.4G wireless transmission technology, low power consumption, strong anti-interference ability. WiFi + Bluetooth connect network can greatly enhance the connect network experience. When the router is disconnected, Bluetooth can also directly connect and control equipment at close range.
• After successful network configuration using [Tuya Smart] app to achieve wireless dimming, remote control, group control, scene control, timing control, music movement, biorhythm, sleep plan, wake plan, one key execution, automation, etc. functions. And it supports 2.4G remote control.

Set up output mode

• Set up correct output mode based on the feature of lights
• Setting method: Press “SET” button continuously to switch output mode (attention: it will log out without operation within 3 seconds)
• Output mode sheet ( confirm output mode based on color of indicator)

Compatible with these 2.4G RF remote controls (Purchased separately)

4G RF Remote control instruction

Linking Code Instructions

1. Power off 10 seconds and power on again or short press ” SET ” one ?me
2. Short press ” I ” button 3 times within 3 seconds.
3. Lights blink 3 times slowly means linking  is done successfully.

Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)

Unlinking Code Instructions

1. Power off 10 seconds and power on again or short press ” SET ” one time
2. Short press ” I ” button 5 times within 3 seconds.
3. Lights blink 10 times quickly means unlinking is done successfully.

Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)

Auto transmiting & Synchronization (only for remote control)

• Remote signal auto transmiting
  One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.

• Dynamic modes auto synchronization
  Multi lights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m)

Dynamic mode table selection (only for remote control)

1. Select dynamic mode table 1:
   While the light is in static mode, short press “ S+ ” button 5 times quickly until blue light flashes 3 times slowly, static mode is activated successfully.

2. Select dynamic mode table 2:
   While the light is in static mode, short press “ S- ” button 5 times quickly until yellow light flashes 3 times slowly, static mode is activated successfully.

Dynamic mode table 1 (default)

Dynamic mode table 2 (need to switch manually)

PWM high frequency / low frequency switching (only for remote control)

• Switch to high frequency (16KHz):
  Press “OFF” button 1 time within three seconds and press “ON” button 5 times, Activated successfully once led light flashes 2 times quickly.

• Switch to low frequency (250Hz):
  Press “ON” button 1 time within three seconds and press “OFF” button 5 times, Activated successfully once led light flashes 2 times slowly.

“Do Not Disturb” mode is activated and shut down (default activated)
Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)

4G RF Remote turn on and turn off instruction

Turn on “Do Not Disturb” mode:
Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light flashes four times quickly.

Attention: Do not disturb mode is activated

1. When the light is OFF status (For example: Use app or remote to turn off light) The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice times to activate light or use APP / remote to activate light)
2. When the light is ON status
   The light is ON status once you turn off and turn on power one time.

Turn off “Do Not Disturb” mode:

• Press “ON” button three times within three seconds and press “OFF” button three times, closed successfully once led light flashes four times slowly.
• Attention: The light will be always “ON” status if you turn on and turn off power once user closed “Do Not Disturb” mode.

App turn on and off “Do Not Disturb” mode instruction (check details in page 8)

Smartphone APP control instruction

Network Configuration (Don’t support 5G router)

1. Download and install [Tuya Smart] app

2. Search for [Tuya Smart] in Apple or Google store or scan following QR code to download and install the app. Please open the app click ” Register ” button to create account while using it in the first time,

3. Log in directly if you already had account.

4. Network Configuration

5. Connect controller with power supply.

6. Confirm indicator light is flashing quickly (2 flashes per second),
   If indicator light isn’t in fast flashing state, there are two ways to enter:

7. Long press ” SET ” key until indicator light flashing quickly.

8. Power off and on controller 3 times.

9. Connect phone with home WiFi network in the 2.4GHz frequency.

10. Open homepage of app and click ” + ” button at the upper right corner of page.

11. Click ” Lighting ” on the left side of page and then click ” Light Source (BLE+Wi-Fi) “

12. Follow app prompts to complete configuration.

App turn on and off “Do Not Disturb” mode (default activated)
Click the light which need to be set up or group control — click “More” — click “Power-on behavior” — turn on or off

Alexa voice control instruction

Please add device into [Tuya Smart] app (check details in page 7), then start following steps

1. Open Alexa App
2. Click “More” on the bottom of right corner
3. Click “Skills & Games”
4. Click “ ” on the top of right corner
5. Type into “Smart life” and search
6. Click “Smart Life” skill, follow instruction to finish configuration and start voice control

Google Home voice control instruction

Please add device into [Tuya Smart] app (check details in page 7), then start following steps

1. Open Google Home App
2. Click “+” on the top of left corner
3. Click “Set up device”
4. Click “Works with Google”
5. Click “ ” on the top of right corner
6. Type into “Smart life” and search
7. Click “Smart Life” skill, follow instruction to finish configuration and start voice control

DMX512 LED Transmitter Control (Purchased separately)

Only for RGB+CCT output mode

DMX512 LED Transmitter Link/Unlink

Follow instruction of DMX512 transmitter (FUTD01), Choose the zone for the light by pressing “ + ” or “ – ” (e.g. “CH12” means zone 12)

Link

• The controller is powered off for 10 seconds and then powered on, or press “ SET ” button 1 time.
• Short press “ ” 3 times within 3 seconds while the indicator of controller is ON
• Link is done once indicator of controller  flashes 3 times slowly

Unlink

• The controller is powered off for 10 seconds and then powered on, or press “ SET ” button 1 time.
• Short press “ ” 5 times within 3 seconds while the indicator of controller is ON
• Unlink is done once indicator of controller  flashes 10 times quickly
• If the link or unlink failed, please follow the above steps again.

Attention

1. Please turn off power supply before installation.
2. Please ensure input voltage to be same as requirements from device.
3. Don’t disassemble device if you are not expert, otherwise it will damage it.
4. Please do not use the light in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.

Scan QR code to watch WiFi series video instruction Or enter into following link directly https://miboxer.com/light/video/wifi_2.html

Made in China

Documents / Resources

| MiBOXER E3-WR 3 In 1 LED Controller [pdf] Instruction Manual
E3-WR, E3-WR 3 In 1 LED Controller, 3 In 1 LED Controller, LED Controller, Controller
---|---

References

• WiFi Series Video - MiBoxer

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>