WARN M8274-50 Winch Mounting Plate Instruction Manual
- June 15, 2024
- WARN
Table of Contents
WARN M8274-50 Winch Mounting Plate
Product Information
- Specifications
- Part Numbers: 87675
- Application: RC Stubby Bumper for 1997+ Jeep JK
- General Safety Precautions
- WARNING: Signals a hazard that could cause serious injury or death if recommendations are not followed.
- CAUTION: Signals a hazard that may cause minor to moderate injury if recommendations are not followed.
- This guide uses NOTICE to call attention to important mechanical information and Note: to emphasize general information worthy of special attention.
- Before You Begin
- This 8274 Winch Mount is designed for mounting an 8274-50 winch on the Warn Rock Crawler Stubby Bumper for 1997+ Jeep JK.
- Contact Information
- WARN INDUSTRIES, INC.
- Address: 12900 S.E. Capps Road, Clackamas, OR USA 97015-8903
- Phone: 1-503-722-1200
- Fax: 1-503-722-3000
- Customer Service: 1-800-543-9276
- Dealer Locator Service: 1-800-910-1122
- International Sales/Customer Service: 1-503-722-3008
- International Fax: 1-503-722-3005
Product Usage Instructions
- Installation Instructions
- Install the Rock Crawler Stubby Bumper according to the installation instructions supplied with that kit.
- Use the 8274 Mounting Plate in place of the standard winch mounting plate included with the Bumper.
- Bolt the 8274 Mounting Plate to the top of the Bumper using the following components:
- 7/16 x 1-1/2 capscrews
- Flat washers
- Lock washers
- Nuts
- Tighten the bolts to the specified torque.
- Use the hardware supplied with the winch and/or bumper to attach the fairlead and winch to the Mounting Plate.
- Note: Careless installation and operation can result in serious injury or equipment damage. Read and understand all safety precautions and operating instructions before installing and operating this product.
- FAQ (Frequently Asked Questions)
- Q: What is the purpose of the 8274 Winch Mount?
- The 8274 Winch Mount is designed to securely mount an 8274-50 winch on the Warn Rock Crawler Stubby Bumper for 1997+ Jeep JK.
- Q: Can I use the standard winch mounting plate included with the Bumper?
- No, you should use the 8274 Mounting Plate provided with this product.
- Q: What tools do I need for installation?
- You will need a 1/4″ socket, 5/16″ socket, 3/8″ socket, 7/16″ socket, and 1/2″ socket.
GENERAL SAFETY PRECAUTIONS
- Your safety, and the safety of others, is very important.
- To help you make informed decisions about safety, we have provided installation and operating instructions and other information on labels and in this guide.
- This information alerts you to potential hazards that could hurt you or others.
- It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.
- CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.
- This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or death. WARNING and CAUTION are signal words that identify the level of hazard.
These signal words mean:
- WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations.
- CAUTION signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.
- This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize general information worthy of special attention.
WARNING
IMPACT AND MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to severe injury or death
- Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical wires, and other objects are not punctured or damaged when/if drilling on the vehicle.
- Thoroughly inspect the area to be drilled (on both sides of material) prior to drilling, and relocate any objects that may be damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or personal injury.
- Always wear safety glasses when installing this kit. A drilling operation will cause flying metal debris.
- Always use extreme caution when cutting and trimming during fitting.
- Always remove jewelry and wear eye protection.
- Never lean over battery while making connections.
- Always insure components will remain secure during installation and operation.
- Always tighten all nuts and bolts securely, per the installation instructions.
- Always inspect, tighten, and replace damaged hardware before use.
- Always replace all worn or damaged parts before operating.
- Never operate this WARN product with damaged or missing parts.
- Never work under vehicle before properly securing vehicle.
- Never operate the vehicle on slopes greater than 10 degrees with the plow installed.
- Read installation and operating instructions thoroughly.
BEFORE YOU BEGIN
- This 8274 Winch Mount is designed for mounting an 8274-50 winch on the Warn Rock Crawler Stubby Bumper for 1997+ Jeep JK.
- WARN INDUSTRIES, INC. 12900 S.E. Capps Road,
- Clackamas, OR USA 97015-8903, 1-503-722-1200, FAX: 1-503-722-3000
- Customer Service: 1-800-543-9276
- Dealer Locator Service: 1-800-910-1122
- International Sales/Customer Service: 1-503-722-3008
- International Fax: 1-503-722-3005
CAUTION
MOVING PARTS ENTANGLEMENT HAZARD
- Failure to observe these instructions could lead to minor or moderate injury
- Always take time to fully read and understand the installation and Operations Guide included with this product.
- Part edges may be sharp!
- Read installation and operating instructions thoroughly.
NOTICE
EQUIPMENT DAMAGE
- Always refer to the Installation and Specification Guide, supplied in the winch kit, for all wiring schematics and specific details on how to wire this WARN product to your vehicle.
- Read installation and operating instructions thoroughly.
PARTS LIST
Description /Qty /Part Number
- 8274 Mounting Plate /1 /87396
- Hardware Kit /1 /87507
TOOLS REQUIRED
- Ratchet
- Torx Bit: T55
- Sockets: 7/16”, 5/8”, 15mm
- End Wrenches: 7/16”
TORQUE SPECIFICATIONS
- 1/4 8 lb. ft. (10.8 N-m)
- 5/16 17 lb. ft. (12.5 N-m)
- 3/8 30 lb. ft. (40.7 N-m)
- 7/16 50 lb. ft. (67.8 N-m)
- 1/2 75 lb. ft. (101.7 N-m)
INSTALLATION INSTRUCTIONS
- Install the Rock Crawler Stubby Bumper according to the installation instructions supplied with that kit.
- Use the 8274 Mounting Plate in place of the standard winch mounting plate included with the Bumper.
- Bolt the 8274 Mounting Plate to the top of the Bumper. Use the 7/16 x 1-1/2” capscrews, flat washers, lock washers and nuts, through each corner. Use 3/8 x 1” carriage bolts, flat washers, lock washers and nuts from the top through the square holes in the top of the Winch Plate. Torque to specification.
- Use the hardware supplied with the winch and/or bumper to attach the fairlead and winch to the Mounting Plate.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS PRODUCT.
©2011 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc. 88011A0
- 8274 WINCH MOUNT
- Part Numbers: 87675
- Application: RC Stubby Bumper for 1997+ Jeep JK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>