YEELIGHT A2101 Ceiling Light User Manual

YEELIGHT A2101 Ceiling Light

Product Description

Mounting Instructions

• Open the package and take out the ceiling light. Push the lock switch inward and remove the base.
• To avoid any danger, please ask and electrical professional to perform mounting or maintenance.
• (Caution, risk of electric shock) Before mounting, make sure to disconnect the power supply to prevent electric shock. Mounting should be performed in strict accordance with the instructions. Improper mounting is liable to cause accidents such as fall, fire, and electric shock.
• Mount the Base.

Method A
Use the impact drill 6mm in diameter to make two mounting holes with a length of ≥ 25mm in the wall (as shown in the following figure.) Put the expansion tube into the mounting hole, and then thread the power cord through the wiring hole. Use self-tapping screws to fix the base on the ceiling, and verify the base is secure-mounted. (Recommended)

Method B
Check that the two mounting points on the lightbox are intact. Then, thread the power cord through the wiring hole. Use metric screws to fix the base on the lightbox on the ceiling, and verify the base is securely mounted.

• The wiring hole is suitable for power leads with a cross-sectional area of 1.5- 2.5mm2. Strip the power cord by 11-13 mm, and connect the neutral, live and ground wires to the ceiling light.

• A solid or stranded hard wire is used as the power lead.

• Connect the neutral, ground, and live wires to the wiring holes marked with N, and L in turn. (When unplugging the power cord, press the red button on the wiring hole first, and then pull it out.)

• Arrange the power cord as shown in the figure, and check for firm wiring.

• This product must be grounded.

• Hold both sides of the light body with both hands. (Be careful not to press the light-emitting surface.) Align the light body with the fixed base, and gently push both sides upwards at the same time. When you hear the “click” sound, the mounting is complete.

• Once you have finished mounting, always rotate the light body left and right and pull the light body up and down to ensure that the lock switch is locked in place.

• Always check for proper mounting after you have finished. Improper mounting may cause the product to fall.

Connect to the Yeelight App

This product can be controlled on the Yeelight App and be configured to interact with other Yeelight products.

Download App
Search for “Yeelight” in an App store or scan the QR code on the right to download and install the App.

Add Device

• Go to the Yeelight App homepage and click “+” in the upper right corner to add your device.
• Proceed with the configuration as instructed on the App.
• Once you’ve added a device successfully, you can find it in the device list.

Note: The operation procedure may differ from what’s described here due to App updates. Please proceed as instructed on the App.
This product can also be controlled on Mi Home, Google Home App, and Amazon Alexa.
You can download and install one of these Apps from an App store, and configure your device as instructed on the App. After you have finished the configuration, you can use the App to control the light.

Apple HomeKit Smart Control

1. Open the Home app on your iPhone or iPad.
2. Tap “Add Accessories” and follow the instructions to scan the QR code either on the back cover of the user manual or on the junction box or enter the 8-digit setup code above the QR code to grant the Apple Home app access.

• Make sure a Wi-Fi network with Internet access is available (this product does not support 5 GHz networks).
• To control this Home-Kit-compatible accessory, it is recommended that you use iOS 9.0 or above. The HomeKit setup code is in the user manual and on the junction box, do not lose it. When adding the product to the Home app after the factory settings are restored, you will need the
• HomeKit setup code again.
• In case the user is lost, remove the lampshade, and scan the QR code or enter the setup code on the junction box.
• iPad and iPhone are trademarks of Apple Inc., and they are registered in the United States and other countries.

Restore to factory settings

Use the wall switch to turn the ceiling light on and off five times consecutively (turn off the ceiling light and wait for two seconds, then turn it on and wait for two seconds, this counts as one time.) The ceiling light then starts breathing and automatically restarts after five seconds, and the factory settings of the ceiling light have been restored.
Note: When using the ceiling light in a new network environment, you need to restore the factory settings and connect to the network again.

Use the Remote Control

• Make sure the remote control and the ceiling light are in the same room.
• Turn on the light and do the following within 60 seconds:
• Press the “OFF” and “M” buttons on the remote control at the same time, and then release them immediately.
• At this point, the indicator light on the remote control starts to flash, indicating that the connection is being made.
• The connection is a successful unit the light flashes cyclically.

Specifications

This product contains a light source of energy efficiency class Replaceable (LED only) light source by a professional

Product Features

Precautions

• Make sure the voltage is consistent with the ceiling light’s operating voltage before use. Using the mismatched voltage may damage the ceiling light and cause safety hazards.
• Do not replace the light source of the ceiling light by yourself. The light source should only be replaced by the manufacturer, after-sales service, or a qualified electrician.
• The ceiling light generates heat during work. Please keep it well-ventilated for heat dissipation.
• This ceiling light can be controlled by an app or remote control (not included, sold separately). Turning off the ceiling light by remote control or app does not cut it off from the electricity, hence, do not touch, replace, or disassemble this ceiling light. Otherwise, it may cause an electric shock, injury, or even death.
• The light installation requires a qualified electrician, and the wiring must comply with IEEE electrical standards or national standards.
• The ceiling light should be installed in a stable location to prevent it from dropping down or falling off.
• Under normal use of conditions, this equipment should keep a separation distance of at least 20 cm between the antenna and the body of the user.
• For indoor users only.
• The light source contained in this luminaire shall only be replaced by the manufacturer his service agent or a similar qualified person.

EU Declaration of Conformity
Quingdao Yeelink Information Technology Co., hereby declares that type Y00409 devices conform with EU Directives. The full text of the EU Declaration of Conformity is available at the following web address: https://edshop.edsystem.cz/prohlaseni-o-shode/article-28393.

WEEE

This product must not be disposed of as normal household waste under the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines under national regulations.

References

• Prohlášení o shodě | eD system a.s.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>