AMERICAN LIGHTING PE-ARC-LENS Spektrum Plus Puck Light Instruction Manual

AMERICAN LIGHTING PE-ARC-LENS Spektrum Plus Puck Light

Specifications

• Input Voltage: 12-24V DC
• Output Current: 4A/CH
• Max Power: 48-96W/CH
• Operating Temperature: -20°C to +50°C

Installation Instructions

Determine the quantities and locations of the pucks, controllers, and drivers to be installed. Consider whether pucks will be surface-mounted or recessed- mounted. Note that multiple drivers and controllers may be required.

Surface Mounting

1. Separate the surface ring from the puck housing. With the puck lens facing away from you, hold the surface ring with your fingers and press on the center of the back of the puck with your thumbs to separate the housing from the surface ring.
2. Determine the desired locations for each puck and mark the locations of the mounting holes on the mounting surface using the surface ring as a template. Note that each puck has a 72″ lead wire which needs to be routed to the controller. Be sure to locate the puck lights so that each puck can reach the controller.
3. Before attaching the surface ring to the mounting surface, route the lead wire through the installation notch.
4. Secure the surface ring using the appropriate mounting hardware (2 screws included).
5. Gently push the puck light into the surface ring until it is fully seated, making sure the lead wire is not pinched or crimped in any way.

Recessed Mounting

1. Separate the surface ring from the puck housing (refer to Surface Mounting Step 1).
2. Determine the desired locations for each puck and mark the locations of their centers on the mounting surface.
3. Drill a 2-3/8″ diameter hole at each marked location.
4. Route the puck’s lead wire through the hole and press the puck in until it is fully seated, making sure the lead wire is not pinched or crimped in any way. The side spring clips will hold the puck light in place.

Controlling the Fixture

These puck lights can be controlled via DMX (REC-DMX-RJ45A-5CH and DMX-RGBTW- 1Z, sold separately) or via Bluetooth Wireless Technology using SPKPL-REC-TB- 5CH with the Spektrum+ Smart Lighting App and/or the Spektrum+ Smart Switch (SPKPL-CTRL-W-RGBTW – sold separately). It is not intended to be used with a standard dimmer switch.

FAQ

Q: Can I use a standard dimmer switch with these puck lights?

A: No, it is not intended to be used with a standard dimmer switch. Please use the compatible controllers mentioned in the installation instructions.

WARNING

• These products may represent a possible shock or fire hazard if improperly installed or attached in any way.
• Products should be installed according to these instructions, current electrical codes, and/or the current National Electric Code (NEC).
• To avoid electrical shock, disconnect or disable power at the source before installation or maintenance.
• To avoid electrical shock, use only 12V DC power supplies.

SAFETY INFORMATION

• Read all instructions before beginning; Save these instructions for future use.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this product.
• The Spektrum+ Puck has an ingress rating of IP44 and is intended for indoor use in dry locations only.
• Do not use it if there is any damage to the unit or the insulation on any cords; Inspect periodically.
• Do not route cords or units through walls, doors, windows, or any similar part of a building structure. Only route cords so they will not be pinched or damaged.
• Do not secure the unit or its power cord with staples, nails, or any other sharp objects that may damage the fixture.
• Not intended for recessed installation inside enclosed cabinetry (cabinets that are not open at the top. Not intended for recessed installation in ceilings or soffits.
• Do not alter plugs or connectors.
• Keep away from curtains, draperies, and other similar flammable materials.
• LEDs are bright! Do not look directly at the lighted fixture.
• LEDs are not serviceable. Do not attempt to open or service LEDs or LED housing.
• This light is not intended for use with a standard wall plate dimmer switch. Use only with Spektrum+ Smart Lighting Bluetooth App or Spektrum+ handheld remote controller (SPKPL-CTRL-W-RGBTW sold separately)

PRE-INSTALLATION

• Determine the quantities and locations of the pucks, controllers, and drivers to be installed, and consider whether pucks will be surface or recessed mounted. Note, that multiple drivers and controllers may be required.

INSTALLATION (See Figures 1-2):

SURFACE MOUNTING

1. Separate the surface ring from the puck housing. With the puck lens facing away from you, hold the surface ring with your fingers and press on the center of the back of the puck with your thumbs to separate the housing from the surface ring. See Figure 1.
2. Determine desired locations for each puck and mark the locations of the mounting holes on the mounting surface using the surface ring as a template. Note: Each puck has a 72” lead wire which needs to be routed to the controller. Be sure to locate the puck lights so that each puck can reach the controller.
3. Before attaching the surface ring to the mounting surface, route the lead wire through the installation notch. See Figure 1.
4. Secure the surface ring using appropriate mounting hardware (2 screws included).
5. Gently push the puck light into the surface ring until it is fully seated, making sure the lead wire is not pinched or crimped in any way.

RECESSED MOUNTING:

1. Separate the surface ring from the puck housing (refer to Surface Mounting Step 1/Figure 1 under SURFACE MOUNTING). Discard the surface ring.
2. Determine desired locations for each puck and mark the locations of their centers on the mounting surface.
3. Drill a 2-3/8” diameter hole at each marked location. See Figure 2.
4. Route the puck’s lead wire through the hole and press the puck in until it is fully seated, making sure the lead wire is not pinched or crimped in any way. The side spring clips will hold the puck light in place.

CONNECTING POWER

• A 24V DC LED driver with a capacity to handle the attached load is required; ADPT-DRJ-30-24 (sold separately) is recommended. Do not exceed the maximum load capacity of the driver.
• It is not recommended to load the driver more than 90% of its rated capacity. Each puck consumes 3 watts.

1. Determine the best location for the driver and controller, considering the 72” lead wire length on each puck.
2. Route each of the lead wires from the puck lights to the appropriate terminal. (see Figure 3)
3. Connect red and black lead wires by attaching them to the controller matching polarity. Red to +, Black to –
4. Connect the driver to a 120VAC household power source.

CONTROLLING THE FIXTURE: These puck lights can be controlled via DMX (REC-DMX-RJ45A-5CH and DMX-RGBTW-1Z, sold separately) or via Bluetooth Wireless Technology using SPKPL-REC-TB-5CH with the Spektrum+ Smart Lighting App and/or the Spektrum+ Smart Switch (SPKPL-CTRL-W-RGBTW – sold separately). It is not intended to be used with a standard dimmer switch.
USING THE SPEKTRUM+ SMART LIGHTING APP: Please follow the Spektrum+ Smart Lighting App guide.the Spektrum+ Smart Lighting App guide.

CARE AND MAINTENANCE

1. Use only a soft cloth to clean the fixture. Harsh chemicals will damage the finish.
2. Do not wipe the fixture with a rough cloth that may scratch the finish or the lens.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

5-YEAR LIMITED PRODUCT WARRANTY

• This product is warranted to be free from defects in material and workmanship for five (5) years from the date of purchase. Products that prove to be defective during this period will be either repaired (i.e. replacement of defective electronics, defective parts of the fixture housing, lens, wiring, switching, or lamp sockets; excluding the lamp) or replaced, at the discretion of American Lighting, Inc claims for defective products must be submitted to the retail location from which the product was purchased within the warranty period. Upon submission of proper return claim documentation and product to American Lighting, Inc. by the retailer, American Lighting, Inc. reserves the right to inspect the product for misuse or abuse. Claims for indirect or consequential damages or for products that, in American Lighting, Inc.’s opinion have been misused, will be denied.
• This is a warranty of product reliability only and not a warranty of merchantability or fitness for a particular purpose. American Lighting, Inc. shall have no liability whatsoever in any event for payment of incidental or consequential damages, including, without limitation, installation costs and damages for personal injury and property. These products may represent a possible shock or fire hazard if improperly installed or altered in any way.
• This warranty is applied only to products that have been properly installed under the instruction sheet and current local codes and/or the National Electrical Code. Warranty does not apply to any product that has been improperly installed or in a situation where components have been altered in any way.

This warranty:

1. excludes expendable parts including but not limited to light bulbs, and batteries;
2. carries a 2-year finish warranty protecting the finish against tarnishing, flaking, and discolorations;
3. does not cover any losses, labor, injuries to persons/property, or costs.

• This warranty does give you specific legal rights and you may have other rights, which vary from state to state, Be careful, it is recommended that installation be done by a qualified professional; the purchaser has sole responsibility for proper installation in compliance with all state and local code requirements. Seller’s employees are not qualified to advise you on the use of this Merchandise. Any oral representation(s) made will not be binding on the seller or its employees.
• The rights under this limited warranty are to the original purchaser of the Merchandise and may not be transferred to any subsequent owner. This limited warranty is in place of all warranties, expressed or implied including warranties or merchantability and fitness for a particular purpose. Seller shall not be liable for any special, incidental, or consequential damages. The sole exclusive remedy against the seller will be for the replacement of any defects as provided herein, as long as the seller is willing or able to replace this product or is willing to refund the purchase price as provided above.
• For questions/comments, technical assistance, or repair parts
• Please call toll-free at 1-800-285-8051 (M-F 8 am-5 pm), CST)
• ©2022 American Lighting, Inc. REV2244www.AmericanLighting.com
• 11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>