ingenico AXIUM EX-MBASE-W1 Multicradle WiFi Base User Guide

AXIUM EX-MBASE-W1
User Guide
www.ingenico.com
13-17 rue Pages, 92150 Suresnes — France
Banks and Acquirers International
Holding, SAS / 814 767 216 RCS Nanterre

Product Introduction

1.1 What’s in the Box – subject to ordered product configuration

• Base host
• User Guide
• 12113:33 A power adapter
• AC power cable
• USB type-B cable
• 5 AXIUM EX8000 Bushings
• 5 AXIUM EX6000 Bushings

1.2 Device Layout

1. Reset Button	2) DC JACK Power Interface	3) RJ45 Network Interface

2. USB – Type B| 5) Power LED|

1.3 Interface definition

1. RS interface
   Sequence| RJ45 Signal
   ---|---
   1| ETH_TX+
   2| ETH_TX-
   3| ETH_RX+
   4| NC
   5| NC
   6| ETH_RX-
   7| NC
   8| NC
2. USB-TYPE B nterface
   Sequence| USB-TYPE B Signal
   ---|---
   1| not connect
   2| D-
   3| D+
   4| GND

Product Technology Features

21 Product Technology Specifications

Port| a DC JACK power port
a RJ45 network port
a USB B DEVICE port supporting USB2.0
---|---
Power| Every Charge output: 5.OVDC 1.0A
Power adapter: input 100-240V AC, 50/60Hz; output 12.0V DC 3.33A
Size and Weight| Size: 311mmx127.8mmx91mm Net Weight : 0.76kg
Gross Weight: 1.50kg

2.2 Environmental Conditions
Environmental conditions for ransportation, storage and operation

2.3 Product Functions

• The base has three main functions as below:

  • Place EX pos on the base o get charged.
  • Place EX pos on the base. Connect the USB type-8 to computer to extend the UsB port
  • Serves as a router, X pos can connect 1o the base via WIFi to extend the network.

2.4 Instructions

The base supports three types of terminal configurations:

We can place it on the base directly.

Note: the slot base
should NOT have any
bushing Inside.| 1. Without the shell, we must take
the EX8000 black bushing.| 1. We must take the EX6000
grey bushing.
2.We must insert the bu hing in the base first.
3.After that we can put EX pos on the base.

WiFi Connection

3.1 Connect EX pos to the base WiFi

• Power on the base
• Click “Settings” menu on EX pos , and then ciick “Base”( step 1)
• Click the *scanning box” [step 2], and scan the Data matrix code label on the back of base.
• The EX pos connect to the base successfull.[step 3]
• Afte that, we can get the “Connected” status.[step 4]

3.2 Web Setting of base

The base can be set from the web

• Use acomputer to connect the bose via Wi

• The web seting IP of base is 192168471 Lagin name is Admin. Passwiord is the

• Paiing Password (Pating Password piease refer o th rear abel for detis)

• User can get the status of base on the status page.

• User can get and change the Etharnat parameter on the Network page.

• User can get and change the WLAN parameter on the WLAN page.

• User can change the operating mode, enable DMZ or set static DHCP on the Advanced page.
  

• User can update the firmware of base, save and reload the settings, change the password on the Manage page.

3.3 Restore factory Setting

• Use paperciip to clck the RESET button for 3 seconds to restore the factory setting of the base.
• The position of RESET button i in chapter

BASE Setting From EX pos

41 Get the Admin permission

• Fist connect EX pos to the base via chapter 3.1

• click “SSID” menu on EX pos [stepl] , and then input the Pairing Password to connect [step2].
  (Pairng Password please refer to the rear abel for details)

• Afte thatwe can enter the base menu and get the manager privieges (Step3].

4.2 Ethernet Parameter Setting
Procedures:

• Tab on “Network” enter WAN Setting or LAN Satting men.
• Enter WAN Setting to get and set the WAN parameter
• Enter LAN Setting to get and set the LAN parameter.

4.3 WLAN Parameter Setting

• Enter WLAN menuStep]
• We can clck “2.4GHz WLAN” to set 2.4 parameter and cick “SGHz WLAN” o set 56Hz WLAN. [Step2]
• We can set channe, RF power, band width and get WLAN MAC on the menu. Step3,4]

4.4 Advanced Setting

• Enter advanced menu,
• We can set the operating mode,DMZ and static DHCP of the base[Chart 1)
• In operating mode,we can set the base work I diferent mode (Chart 21,
• We can set DMZ(Chart 3]and add static DHCP[Chart 4]

4.5 Operating Mode
4.51 Gateway Mode

• Local networkIONU distrbute the P to base ETH port.
• Base distrbute the P10 EX pos
• Local network/ONU and EX pos are not in the same network segment

4.5.2 8ridge Mode

• Base distribute the I 1o the Local network and EX pos.
• They are in the same netwiork segment

4.5.3 WiFi Repeater Mode

• It is a mode to expand coverage of base.
• For example , Ex pos s to0 far away to connect Base A. So we can put Base 8 between Base A and EX pos.
• Set Base 8 to repeat the Base A, EX pos can connect to internet via 8ase B.

4.6 Management Setting
4.6.1 Upgrade the firmware of base

• First,we use software manager to install the wifidockfirmware.apk in EX pos, as follow
• Second, we get the Admin permission of the base with EX pos via chapter
  4.1, Wait for upgrading. [Step1].And get the successful tips(Step2]. Check the Version of the baselStep3]4.6.2 Save the setting of base4.6.3 Load the setting o base:

FAQs

Q1: The base fails to connect EX pos.

Causel: EX pos WLAN is not yet opened. Solution: Open WLAN via the drop-down box of EX pos. Cause 2: EX pos is placed too far away from base. Solution: Place and connect the devices within 20 meters, Cause 3: The password of EX pos base is changed Solution: Input the correct password , or restore factory setting to get the. default password

Q2: Why mobile phone can not search the 5G WIFI?

Solution: Check whether mobile phone can support SG WIFi

Notes

Prevent the terminal from sun exposure, high temperature, moster and other mean conditions
Cut off the power before claaning the device and wipa the main body with dry cloth.
When the following abnormal phenomena oceur, stop running the device immediately, cut off the power supply, and report to the service provider as soon as possible:

• Harsh noise heard during operation.
• Impurities or water found in the machine.
• Unpleasant smell found during operation

Delivery and Storage

Daliver the device in normal way, avoiding rain and snow, sun exposure and mechanical impact.
The product should be stored in the original bos. The box shouid be at least 15cm away from the floor, at least 50cm from the wall, heat source, cold saurce, window or air iniet.

Power Adapter

The base can only be connected to the adapter which is provided with AXIUM Ex- MBASE-W1

WARNING
The power adapter provided is specially designed for ingenico AXIUM EX- MBASE-WI. Do not use any other power supply. The use of a power supply with apparently. similar voltage/current characteristics may damage your terminal.
RF exposure
The antenna of the product, under normal use condition is at least 20cm away.
from the body of the user. Warning statement o the user for keeping 20cm separation distance and the prohibition of operating to a person has been printed on the user manual. So, this product under normal use is 10cated on electromagnetic far field between the human body.

Standards

CE Marking
The CE marking indicates AXIUM EX-MBASE-W1 complies with the requirements of European Directive 2014/53/EU on Radio Equipment for

• “The protection of the health and the safety of the user and any other person.
• “The protection requirements with respect to electromagnetic compatibity.
• ‘And complies with harmonized standards.

‘Operating Frequency Band (RF):

5250-5350MHz
5470-5725MHz
5725-5850MHz| 5150-5250MHz
5250-5350MHz
5450-5725MHz
5750-5850MHz

“The terminal user does not have permission to access the frequency band not used by this product

Transimission pover (max):

vHT80)

Restrictions i the 5GHz band
According to Article 10(10) of Directive 2014/S3/EU, the packaging shows that this terminal willbe subject to some restrctions when placed on the market. In all EU member states, operation of 5150-5350MHz is restricted to indoor use only.

Environment (WEEE, Batteries and packaging)

s product s labeled in accordance with European Directives 2012/19/EU concerning Waste Electrcal and Electronic Equipment (WEEE) and 2013/56/EU concerning Bateries and Accumulators. Those provisions are requiring producers and manufacturers become labie for take-back, treatment and recycling upon end of Ife of equipment and batieries.

THE PRODUCT

“The crossed-out waste bin stuck on the product, o ts accessories means.
that the product belongs to the family of electrical and electronic equipment, and waste batteries must not be thrown away but collected separately and recycles. Please contact your retallers for more detailed information about the compliance solution in place for disposing of your old product and used batteries. Packaging waste must also be collected separately to assure a proper disposal and recyciing. In this way you can participate In the re-use and uUpgrading of Electrical and Electronic Equipment Waste, which can have an effect on the environment and human heaith INGENICO is a trademark of BANKS AND ACQUIRERS INTERNATIONAL HOLDING . This Document is Copyright © 2023 BANKS AND ACQUIRERS INTERNATIONAL HOLDING . BANKS.
AND ACQURERS INTERNATIONAL HOLDING retains ful copyright ownersti, rights and protection nal mterial ontained in his document. The recipient can receive his document on the conltion thathe wit keep the document confidential and wil ot use ts contents i any form or by any means, except as agreed beforehand, without the prir wilten permission of BANKS AND ACQURERS INTERNATIONAL HOLDING. Moreover, nobody is authorzed to piace this ‘Gocument at the disposalof any thid party without he pror written permisson of BANKS AND ACQURERS INTERNATIONAL HOLDING, If such perision i granted, 1t il be subject to the condition that the recpient ensures that any ther recipient of this document, of nformation ‘contained therein, is held responsibi 1o BANKS AND ACQURERS INTERNATIONAL HOLDING for the confidentaty of that information. Care has been taken to ensure that the content of this
document s as accurate as possible. BANKS AND ACQUIRERS INTERNATIONAL HOLDING however declines any responsibilty for inaccurate, Incomplete or outdated nfomaton. The contents of tis document may change from time to tme wihout prior notice, and do not create, specity, oy of replace any new or prior contractual obigations agreed upon i witing betieen BANKS AND ACQUIRERS INTERNATIONAL HOLDING and the user. BANKS AND.
ACQUIRERS INTERNATIONAL HOLDING is not respansite for ny use of this device, which voud o non-consistent with the pesent document. Al trademarks used inthis document remain the.
property of therrightfl owners”

AXIUM EX-MBASE-W1 07/25
Copyright© 2023 Ingenico —Banks and Acquirers International Holding SAS All rights reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>