namron 1402769 Zigbee LED Dimmer 250W Instruction Manual

namron 1402769 Zigbee LED Dimmer 250W

Product Information

Specifications

• Product Name: Namron Zigbee LED Dimmer 250W
• Input Voltage: 220-240V~50/60Hz
• IP Rating : IP20
• Dimmer Type: Push/Rotary
• Wiring System: Two-way switch with push switch
• Dimmer Type: Trailing edge
• Minimum Load:
  • LED Lamp: 5-250W
  • Electronic Transformer/Halogen: 5-250W
  • Halogen Lamp 240V: 5-250W
• Installation: Must be installed by a registered electrical company
• Mounting: Mounts in the standard electrical box or surface mounting
• Protection Features:
  • Short-circuit protection
  • Overload protection
  • Over-temperature protection
  • Lamp breakdown protection
• Radio Frequency: 2.4GHz

Product Usage Instructions

Minimum Set Switch
Use the Minimum Set Switch to set a minimum dimming level.

Reset Key
Use the Reset Key for network pairing, touchlink, and factory reset of the dimmer.

Indicator Light
The Indicator Light illustrates different settings with each having its own color.

Dimmer Wheel
The Dimmer Wheel is used to adjust the dimming level.

Operating Instructions

1. Short press the dimmer wheel four times and long press on the fifth time. The connected load will flash twice to indicate that the dimmer has entered setting mode.
2. Adjust your desired starting level using the dimmer wheel.
3. To save the desired setting, press and hold the dimmer wheel. The load will flash once to indicate that the setting has been saved.

Factory Reset of Start Level

1. Short press the dimmer wheel five times and long press on the sixth time.
2. The connected load will flash once to indicate that it has been set to the factory setting.

Zigbee Network Pairing

1. Remove the device from the previous Zigbee network if it has already been added. Otherwise, pairing will fail. Please refer to the Factory Reset Manually section for instructions.
2. From your Zigbee controller or hub interface, choose to add a lighting device and enter pairing mode as instructed by the controller.
3. Double press the reset button to activate the network pairing mode (The blue indicator light will be flashing). The network pairing mode will last for 15 minutes. If it times out, repeat this step.
4. The blue indicator light will stop flashing and remain solid for 10 seconds. Then, the device will appear in your controller’s menu and can be controlled through the controller or hub interface.

TouchLink to a Zigbee Controller
Put the device you want to TouchLink with the dimmer into Touchlink pairing mode. Please refer to the device’s user manual for information on how to do this.

FAQ (Frequently Asked Questions)

• Q: What is the minimum load for the Namron Zigbee LED Dimmer 250W?
  A: The minimum load depends on the type of light source or electronic converter. It may be necessary to increase the load to 10W.

• Q: Can I install the dimmer myself?
  A: No, the dimmer must be installed by a registered electrical company.

• Q: What are the protection features of the dimmer?
  A: The dimmer has short-circuit protection, overload protection, over- temperature protection, and lamp breakdown protection.

INSTRUCTION

This is a push/rotary dimmer. The dimmer may be used in the two way switch wiring system with push switch. The dimmer is trailing edge. Min. load depends on the type of light source or electronic converter. It may be necessary to increase the load to 10W. Must be installed by registered electrical company.

• Operating voltage: 220-240V~ 50/60Hz
• LED lamp: 5-250W
• Electronic transformer /halogen: 5-250W
• Halogen Lamp 240V: 5-250W

Mounts in the standard electrical box or surface mounting

• Short-circuit protection
• Over load protection
• Over temperature protection
• Lamp breakdown protection

OVERVIEW

• Min. set switch
  Use it for set a minimum dimming level.

• Reset key
  Use it for network pairing, touchlink, factory reset of the dimmer

• Indicator light
  Indicate different color depending on setting.

• Radio frequency
  2,4GhHz

OPERATION

Set desired start level

1. Short press the dimmer wheel 4 times and long press on the 5th time. The connected load will flash twice to indicate that the dimmer has entered setting mode.
2. Adjust yout desired start level.
3. To save wanted setting, press and hold the dimmer wheel. The load will flash once to indicate that the setting is saved.

To factory reset the start level

1. Short press dimmer wheel 5 times and long press on 6th time.
2. Connected load will flash one time to indicate that it has been set to factory setting.

Note: All configuration parameters will be reset after the device is reset or removed from the network.

ZIGBEE NETWORK SETTING

Zigbee network Pairing

1. Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually.”
2. From your Zigbee controller or hub interface, choose to add lighting device and enter pairing mode as instructed by the controller.
3. Double press the reset button to activate the network paring mode(The blue indicator light will be flashing), network pairing mode will last for 15-minutes once timeout repeat this step.
4. The blue indicator light will stop flashing and solid on for 10s then the device will appear in your controller’s menu and can be controlled through controller or hub interface.

TouchLink to a Zigbee remote

1. Short press “Reset” button 4 times.
2. The green indicator light will start flashing to show that the device is in touchlink commissioning. 180s timeout repeat this step.
3. Bring the remote or touch panel within 10cm of the lighting device.
4. Set the remote or touch panel into TouchLink commissioning, please refer to corresponding remote or touch panel manual to learn now.
5. The connecting lights will start flashing to indicate the pairing processing. Once paired both the connecting lights and the green indicator light will stop flashing and you can control the lights by the remote.

Note

1. Directly Touchlink (both not added to a Zigbee network),each device can link with 1 remote.
2. Touchlink after both added to a Zigbee network, each device can link with max. 30remotes.
3. For Hue Bridge & Amazon Echo Plus, add remote and device to network first then Touchlink.
4. After Touchlink, the device can be controlled by the linked remotes.

Find and Bind Mode

1. Press the reset button 5times.
2. The yellow indicator light will start flashing. 180s timeout repeat this step.
3. Set the remote or touch panel(target node)into find and bind mode, and enable it to find and bind indicator, please refer to corresponding remote or touch panel manual.
4. There shall be indication on the remote or touch panel that it bind the device successfully and can control it then to learn how.

Note Make sure the device and remote already added to the same Zigbee network.

Setup a Zigbee network & Add other devices to the network (No coordinator required)

1. Press the reset button for 6times to enable the device to setup a zigbee network.
2. The white indicator light will start flashing and stay solid for 10s to show the dimmer has created the zigbee network successfully.
3. Press the reset button for 7times to allow other devices to be added into the network. The red indicator light will be flashing continuously.
4. Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals. 180s timeout limit.
5. Pair more devices and remotes to the network as you would like, refer to their manuals.
6. Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.

Note

1. Each added device can link and be controlled by max. 30 added remotes.
2. Please refer to remote instructions of how many devices can be linked.

Zigbee Clusters the device supports are as follows:

• Input clusters
  • 0x0000: Basic
  • 0x0003: Identify
  • 0x0004: Group
  • 0x0005: Scenes
  • 0x0006: On/off
  • 0x0008: Level Control

Wiring diagram

1. Two wire connection without neutral.
2. Three wire connection with neutral.
3. Optional control method: Push Button Switch.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>