WASSERSTEIN Aqua pal Water Sensor and Smart Leak Detector User Manual

WASSERSTEIN Aqua pal Water Sensor and Smart Leak Detector

About Aqua Pal

The Aqua Pal continuously monitors the water pressure, temperature, and flow rate, as well as detects minor leaks in a water system.

In the Box

• 1 x Aqua Pal

• 2 x water pipe adapters (N20 to 3/4 in)

• 2 x waterproof tape (10 ft)

• 1 x power cable (16.4 ft)

• 2 x waterproof pads

• 2 x threaded protection covers (pre-installed)

• 1 x power adapter (5V / 2A)

Important Information

1. The Aqua Pal cannot be used if the water temperature is below freezing (32 °F / 0 °C).
2. Wrap the waterproof tape around the water pipe adapter and the copper pipe to prevent water leakage.
3. It is recommended to install the Aqua Pal indoors. And install Aqua Pal in the main pipe or sub-pipe.
4. Make sure you shut off your water source before installation

Introduction to Parts

Indicator Lights

flashes every 2 seconds in paring mode. The BLUE indicator light stays on when successfully connected.
Valve On / Off| Indicator light flashes (green: on, red: off)
Reset| Press the connection button for 5 seconds, the reset button indicator will flash slowly (meaning the Aqua Pal is waiting for configuration).

How to Install

Note: Before you install the Aqua Pal, test that the device can power on and connect to the network. Shut off your water source until after installation is completed.

Water pipe installation:

1. Wrap the waterproof tape around the threads of the water pipe adapter.

2. Screw the water pipe adapter into the main pipe.

3. Tighten the water pipe adapter using a hex key (not provided).
   

4. Wrap the waterproof tape around the threads of the Aqua Pal pipe.

5. Put the waterproof pad into the water pipe adapter. Then, dock the Aqua Pal copper pipe.
   

6. Tighten the adapter nut with a crescent wrench (not included).

7. Repeat steps 1 – 6 to install the other side of the Aqua Pal.

Connecting to Power

Power cable installation:
Press the power cable firmly into the power slot and turn the nut clockwise to lock it in place.

App Setup

Minimum requirements:

• Smartphone or tablet running iOS 10.0 or later / Android 5.0 or later
• Wireless communication standard: IEEE 802.11 b/g/n
• Frequency band: 2.4 GHz & 5 GHz
• Security Protocols: WPA, WPA2
• Encryption Protocols: TKIP, AES
• Connection speed: Minimum: 2 Mbps (download) / 2 Mbps (upload)

How to Download the Wasserstein App and Add Your Device

1. Download the Wasserstein App by scanning the QR code or by searching “ Wasserstein” in Google Play Store or the App Store.
   |
   ---|---
   
2. Sign up for a new account or log in to an existing account.
3. There are 3 ways to add your device: Bluetooth, Wi-Fi EZ mode, and Wi-Fi AP mode.

Bluetooth (Default pairing mode):

Note: Enable Bluetooth on your mobile device and follow onscreen instructions to add your device.

1. Press “Connection” for 5 seconds on your Aqua Pal until the blue light is on.

2. Click “Add Device” or “+” in the top right corner on your mobile device.

3. Click “Go to add” in the pop up dialog box.

4. Follow in-app instructions to connect the Aqual Pal to your Wi-Fi network.

5. Wait until the process is completed (about 30 seconds). Then click “Next”.

6. Choose a room, then click “Done” in the top right corner to complete.

Wi-Fi EZ mode (Only need to use when other pairing mode fails):

Note : You need to disable your Bluetooth in this mode, only use a Wi-Fi connection.

1. Click “Add Device” or “+” in the top right corner

2. Click the Aqua Pal (Wi-Fi) icon in the bottom right corner.

3. Follow the in-app instructions to connect the Aqual Pal to your Wi-Fi network.

4. Press “Connection” for 5 seconds on the Aqua Pal until the blue light is on.

5. Select “Confirm the indicator is blinking rapidly” and click “Next”.

6. Wait for “Adding device” to complete.

7. Choose a room and click “Done” to complete.

Wi-Fi AP mode (Only need to use when other pairing mode fails):

Note: Disable Bluetooth in this mode and ONLY use Wi-Fi connection.

1. Click “Add Device” or “+” in the top right corner.

2. Click Aqua Pal (Wi-Fi) icon in the bottom right corner.

3. Follow in-app instructions to connect the Aqual Pal to your Wi-Fi network.

4. Click “EZ Mode” in the top right corner to switch, select “AP Mode” in the drop down list.

5. Switched to “AP Mode”.

6. Press “Connection” for 5 seconds on the Aqua Pal until the blue light is on.

7. Check “Confirm the indicator is blinking rapidly” and click “Next” on your phone.

8. Click “Go to Connect”.

9. Click “SmartLife- XXXX” hotspot.

10. Once the connection is established, return to the Wasserstein App by clicking “Wasserstein” in the top left corner.

11. Wait for “Adding device” to complete.

12. Choose a room and click “Done” in the top right corner to complete.

After any of the pairing modes is complete, you can then use the App to monitor and control the settings of your Aqua Pal.

Checking Leakage with Aqua Pal

1. Go to Check Leakage & Click “Test” to start.

2. Make sure to turn off your water source and click “Confirm”.

3. Wait for the self-test to be completed
   

Reviewing Water Usage History

Click “My Water” to review water usage history.

Resetting Water Usage History with Aqua Pal

Click “My Water” to review water usage history.

1. Go to settings and select “Reset Water Usage”.

2. Click “Confirm” to reset.

Setting Temperature, Pressure & Flowrate Threshold

1. Select “Aqua Pal” in device list from Home page

2. On the main screen, click “Settings” in the bottom right corner

3. On the “Settings” page, click “Temperature Alarm”.

4. Set the temperature alarm threshold by sliding the slider.

5. Do the same for the Pressure Alarm and Flow Rate Alarm.
   

Warning messages by Wasserstein App

1. High / Low Temperature Alarm

2. High / Low Pressure Alarm

3. High / Low Flow Rate Alarm

Connecting Smart Water Sensor with Aqua Pal

1. Make sure you have installed the Aqua Pal and Smart Water Sensor in device list from the Home page.

2. Click Smart icon at bottom, and then click “+” in the top right corner.

3. Select “When device status changes” from Create Smart screen.

4. On the All Devices list, select “Smart Water Sensor”.

5. Select “Flooding State” from “Select Function” page.

6. On the “Create Smart” page, select “Run the device”.

7. On the All Devices list, select “Aqua Pal”.

8. Select “Switch” from Select Function page, then set the Switch to “Off” and click “Save”, click “Next” in the top right corner.

9. Click “Save” to complete.

10. Click “Yes” to start using the Automation.

11. Automation saved.

Specifications

Power supply: DC 5V / 2A
Max working current: 800 mA
Standby power consumption: 0.3 W
Valve on/off time: 24 sec
Valve diameter: DN20 3/4 in
Water pressure: 0 – 100 PSI
Wireless frequency: 2.4 / 5 GHz
Bluetooth version: Bluetooth 5.0
Wi-Fi distance: 148 ft
Waterproof rating: IPX7
Size: 7.7(L) x 3(D) x 4(H) in
Operating temp: 32 – 122 °F
Storage temp: 14 – 149 °F
Storage humidity: 10 – 80%

Get More Support

Scan the QR code below or email us at contact@wasserstein- home.com.

www.wasserstein-home.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>