ELKAY NFC3 Drinking Water Cooler and Bottle Filler User Manual

: June 15, 2024
: ELKAY

Table of Contents

ELKAY NFC3 Drinking Water Cooler and Bottle Filler
Product Information
Product Usage Instructions
Sub Menu 2
Service Instructions
Cleaning
Temperature Control
Stream Height Adjustment
Register in plumb SMART
FCC COMPLIANCE STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ELKAY NFC3 Drinking Water Cooler and Bottle Filler

Product Information

Specifications

Model: LZSTL8WSSP-W1
Basin: 11
Water Inlet: 3/8
Filter Assy: 51300C – 3000 Gal.
Filter Head Fittings Kit: 1000005214 – includes John Guest Fittings & 3/8 Elbow, Filter Bracket/Screws
NFC Board/Cover Kit: 1000004409

Product Usage Instructions

Lower and Upper Shroud
To access the refrigeration system and plumbing connections, follow these steps:

Remove two (2) screws from the front of the cooler to remove the lower shroud.
To remove the upper shroud for access to the pushbars, regulator, solenoid valve, or other components located in the top of the unit, do the following:
Remove the lower shroud.
Disconnect the drain.
Remove four screws from tabs along the lower edge of the upper shroud.
Unplug two wires and water tube.

Bubbler
To remove the bubbler, follow these steps:

Disconnect the power supply.
Reach the underside of the bubbler through the access panel on the underside of the upper shroud.
Remove the access panel by removing the retaining screw.
To remove the bubbler, loosen the locknut from the underside of the bubbler and remove the tubing from the quick connect fitting per the Operation Of Quick Connect Fittings section in the General Instructions.
After servicing, replace the access panel and retaining screw.

Switches Behind the Push Bar

The regulator in an EZ cooler is always held fully open by the use of a single regulator nut. Water is not dispensed until the pushbar is depressed to activate a switch which then opens a solenoid valve.
To remove sidebars, from the inside compress the flared tabs and pull out carefully. To reinstall side pushbars, insert the front of the pushbar first. While keeping the switch depressed, snap the rear of the pushbar into position.

Cleaning

Clean stainless steel components with a uniform finish pattern.
Clean plastic components according to their properties.

Programming Instruction

To activate the main menu, depress the button for 3 seconds and then release. The menu will cycle through main menu items for 2 seconds each for 2 cycles and then exit unless selected. It will also cycle through sub menu items for 2 seconds each for 2 cycles and then return to the main menu unless selected. Selections are saved when the menu is exited.

Main Menu

Momentary: Scrolls through all the settings on unit
Momentary: Flashes error code
Momentary: Sets time
Momentary: Sets filter status and errors

Sub Menu 1

Momentary: Sets day (Sunday-Saturday)
Momentary: Sets AM/PM
Momentary: Sets hour (12 hour)
Momentary: Sets filter
Momentary: Sets minute (0-69 in 5 minute increments)

Momentary: Turns off filter status and errors
Momentary: Default setting – Turns on filter status and errors

Refrig Range

FAQ

Q: How do I remove the lower and upper shrouds?
A: To remove the lower shroud, remove the two screws from the front of the cooler. To remove the upper shroud, first remove the lower shroud, then disconnect the drain, remove four screws from tabs along the lower edge of the upper shroud, unplug two wires and water tube.
Q: How do I remove the bubbler?
A: To remove the bubbler, first disconnect the power supply. Then reach the underside of the bubbler through the access panel on the underside of the upper shroud. Remove the access panel by removing the retaining screw. Loosen the locknut from the underside of the bubbler and remove the tubing from the quick connect fitting per the Operation Of Quick Connect Fittings section in the General Instructions. After servicing, replace the access panel and retaining screw.
Q: How do I clean the product?
A: Clean stainless steel components with a uniform finish pattern. Clean plastic components according to their properties.

NOTE:
When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten

WATERSENTRY ® **** FILTER PARTS LIST

Kit – Filter Head Fittings includes
John Guest Fittings & 3/8” Elbow

3| 1000004409| Filter Bracket/Screws Kit – NFC Board/Cover

Service Instructions

Lower and Upper Shroud
To access the refrigeration system and plumbing connections, remove two (2) screws from front of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
Bubbler
To remove the bubbler, first disconnect the power supply. The underside of the bubbler can be reached through the access panel on the underside of the upper shroud. Remove the access panel by removing the retaining screw. To remove the bubbler, loosen locknut from the underside of the bubbler and remove the tubing from the quick connect fitting per the Operation Of Quick Connect Fittings section in the General Instructions. After servicing, replace the access panel and retaining screw.
Switches Behind the Push Bar

The regulator in an EZ cooler is always held fully open by the use of a single regulator nut. Water is not dispensed until the pushbar is depressed to activate a switch which then opens a solenoid valve.
To remove sidebars, from the inside compress the flared tabs and pull out carefully. To reinstall side pushbars, the front of the pushbar is inserted first. While keeping the switch depressed, snap the rear of the pushbar into position.

Cleaning

Stainless Steel
- General cleaning: use an ordinary mild detergent and soft cloth, rinse and towel dry.
- Steel soap pads should never be used; particles can adhere to a stainless steel basin surface and will eventually rust.
- Light scratches are normal for stainless steel basins; over time they will blend into the uniform finish pattern.
Plastic Components
- General cleanin g: use an ordinary mild detergent and soft cloth, rinse and towel dry. Wiping the surface clean to remove debris or build up will not hurt the antimicrobial properties.

Temperature Control

Factory set at 50°F (+/- 5°F) under normal conditions. For temperature adjustments, refer to sticker on left side of top bar.

Stream Height Adjustment

VIEW OF UNDERSIDE OF BASIN SHROUD

ELKAY-NFC3-Drinking-Water-Cooler-and-Bottle-Filler-8

LZSTL8WSSP-W1

Programming Instruction

Pictured is unit only without bottle filler.
Note: Danger! Electrical shock hazard. Disconnect power before servicing unit.

Uses HFC-134A refrigerant

ELKAY-NFC3-Drinking-Water-Cooler-and-Bottle-Filler-5

ATTENTION:
If the product serial number is before 190424189, please refer to archived documents section of Elkay.com for the most accurate parts list. (www.elkay.com/archived-documents)

115V PARTS LIST
ITEM NO.| PART NO.| DESCRIPTION|
1| 28401C| Hanger Bracket|
2A| 55001109| Basin – Stainless Steel|
2B| 0000001337| Basin – Bottle Filler Stainless Steel|
3| 36216C| Wiring – Front/Side Push Bar|
*4| 36322C| Compr – Service Pak 115V EMIS70HHR|
5| 56092C| Tube – Poly (Cut To Length)|
6| 56229C| Assy – Shroud – Upper (Front Side Push)|
7| 66703C| Drier|
8| 56213C| Access Panel|
9| 1000004572| Kit – Solenoid Valve/Regulator Assembly|
10| 1000004564| Kit – Regulator W/Holder & Nut|
11| 56073C| Replacement Bubbler Assy|
12| 98734C| Kit – Pushbar (Front/Side) TL|
13| 1000001600| Kit – Pushbar (Front Only)|
14| 35980C| Power Cord Non-Refrigerated|
15| 1000004568| Power Cord – EZTL8|
16| 98775C| Kit – Fan Motor/Blade/Screws/Nut|
17| 98776C| Kit – Condenser/Drier/WireTies|
18| 98777C| Kit – Compr Mtg Hdwe/Grommets/|
| | Clips/Studs|
19| 98778C| Kit – Heatx/Drier|
20| 98898C| Kit – Hardware|
21| 0000000238| Kit – 115V Electricals (Relay, Ovrld, Cover)|
22| 98724C| Kit – Evap. Replacement|
23| 1000001602| Kit – 75583C Elbow 5/16″ x 1/4″ (3 Pack)|
24| 1000004547| Harness – Cooler|
25| 1000004550| Wire – 6” Jumper|
26| 1000004559| Wire Assy – Jumper|
27| 1000004447| Wasteline Drain Assy|
28A| 98900C| Kit – Drain Replace TL|
28B| 97969C| Kit – Drain Replace (TL) LR|
29| 1000001812| Kit – Bottle Filler Drain|
30| 98773C| Kit – Cold Control|
NS| 2000001220| Kit – Panel (Wrapper) Stainless TL|
| 2000001210| Kit – Panel (Wrapper) Stainless LZTLD|
NS| 28024C| Filler – Wrapper Light Grey LZTLD|
| 28025C| Filler – Wrapper Stainless LZTLD|
NS| 1000001892| Bracket – Trim Strip Light Grey LZTLD|
| 1000001891| Bracket – Trim Strip Stainless LZTLD|
NS| 1000001894| Panel – Universal Trim Light Grey LZTLD|
| 1000001893| Panel – Universal Trim Stainless LZTLD|
NS = Not Shown NS = No semuestra|

INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or orders for repair parts MUST include Model No. and Serial No. of cooler, name and part number of replacement part.

|
ITEM NO.| PART NO.| DESCRIPTION|
NS| 98546C| Kit – Aerator Replacement|
31| 98549C| Kit – Hardware & Waterway (BF)|
32| 1000004573| Kit – Solenoid Valve 120V (BF)|
NS| 1000005077| Nameplate – Elkay Filtered|
33| 1000002433| Kit – Top Cover Assy (BF)|
34| 1000005219| Kit – IR Sensor K+|
35| 2000000832| Kit – Connected Ready Control Board|
NS| 1000004436| Kit – Tower/Basin Gasket|
36| 1000004546| Harness – Bottle Filler|
37| 1000004549| Harness – LED/IR Board|
38| 2000001084| End-point Board|
39

40

|

2000001085
2000001086

| Harness – End-point Board Bracket, End-point Board Mounting|

Register in plumb SMART

Install Zorn Gateway per the Gateway Instructions Manual (Required & Sold Separately)
Request plumbSMART Administrator Account at 844-987-6737
Zorn creates your Enterprise Account for you! (You will be required to identify your building location, number of floors, and number of rooms.)
Log in to plumbsmart.zurn.com
Register each Connected Product in plumbSMART (Watch How-To Videos to Get Started. Located in the support section inside the portal.)
Note: Refer PlumbSMART Registration ID Label provided with Connected Product 6. Now, Relax. You’re Connected.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device shall be used in such a manner that the potential for human contact normal operation is minimized. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

This device may not cause interference, and
This device must accept any interference, including interference that may cause undesired operation of the device.

The device shall be used in such a manner that the potential for human contact normal operation is minimized. This equipment complies with RSS-102 radiation exposure limits.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

ELKAY MANUFACTURING Co.