LINIZ zDental Model X Stone Fastest Dental Printing Instruction Manual
- June 15, 2024
- LINIZ
Table of Contents
LINIZ zDental Model X Stone Fastest Dental Printing
Product Information
Specifications
- Product Name: zDental Model X Stone
- Colour: Stone or light grey
- Package Size: 500ml/bottle or 5L/drum
Washing
- Wash the printed parts in an IPA (Isopropyl Alcohol) bath with at least 98% purity for best results.
- Pre and post-washing can be performed to ensure thorough cleaning of the models.
FAQ
- Q: Can dental Model X Stone be used for creating implant models?
- A: Yes, dental Model X Stone is suitable for creating implant models.
- Q: What precautions should I take when using this resin?
- A: When using this resin, it is important to wear nitrile rubber gloves and a face mask. Ensure that the room is well-ventilated. Avoid direct contact between the resin and the skin. In case of contact, wash the affected area with cold water and seek medical attention if discomfort persists. If the resin splashes into the eyes, flush with water and seek immediate medical attention.
- Q: How should I store the remaining resin after printing?
- A: It is recommended to transfer the remaining resin back into the bottle and avoid leaving it in the resin tank for a long time.
- Q: What layer thickness can be used for printing with zDental Model X Stone?
- A: zDental Model X Stone can be printed with a layer thickness of 50m or 100m.
Instruction for Use
Product Discription
zDental Model X Stone is a light-curing resin for the production of dental
models using 3D LCD printers utilizing wavelengths between 385nm–405nm.
zDental Model X Stone is an effective and fast-printing resin. This low-
viscosity model material is ideal for diagnostic models and orthodontic
appliance models requiring excellent precision, long-term dimensional
stability, high reliability, superior fit and easy cleaning. zDental Model X
Stone has excellent anti-sedimentation activity which makes handling easy.
Intended Use
Diagnostic models die models, implant models, orthodontic models
Colour and Package
Stone or light gray, 500ml/bottle, or 5L/drum
Contra-indications
zDental Model X Stone contains (meth)acrylate and phosphine oxide which can
cause allergic reactions at skin contact. In case of an allergic reaction,
please contact a medical physician.
Use and Safety Information
- Wear nitrile rubber gloves and a face mask when using this resin.
- Keep the room ventilated.
- Swallowing such as eating and drinking is forbidden in the printing place.
- Avoid liquid or incompletely cured resin directly in contact with the skin. If contact with skin occurs, wipe resin away and wash thoroughly with cold water, use hand sanitiser or soap to assist in washing. If the users still feel uncomfortable, please see a doctor immediately.
- If the user accidentally splashes the resin in the eyes, flush with plenty of water and seek medical attention immediately.
- For more safety details please refer MSDS of this resin.
- The good use temperature for this resin is 21 – 25 ℃. Keep the resin away from direct sunlight or any kind of UV light.
Processing printed parts
Mixing resin before using
- In Bottle: Shake the bottle vigorously before pouring it into resin tank.
- In resin tank: Stir resin with a soft spatula. Take care not to damage the film of the resin tank.
- This step is necessary to avoid getting a bad printing job caused by the (possible) pigment sediment from the bottom of the vessel.
- After the model is printed, it is recommended to restore the remaining resin into the bottle and avoid
- leave the resin in the resin tank for a long time.
Preparation
Prepare a print job using slicing software, such as Uniz Dental, Uniz Desktop
or Uniz Maker, depending on the UNIZ printer type. zDental Model X Stone can
be printed in a layer thickness of 50μm or 100μm. For more information, please
refer to the Uniz Dental Software Guide (www.uniz.com).
Printing
Turn on the printer and ensure it is well. Check and clean the build platform,
resin tank, and LCD printing screen. Put the resin tank filled with mixed
resin onto the LCD printing screen, and fix the tank well onto the screen.
Upload the slicing file into the printer through USB or WIFI, then start
printing.
For more information, refer to the printer instructions
(www.uniz.com).
Post-processing
Detaching printed parts
Once the printing process has ended, a dripping time of resin of approximately
10 min is recommended, using a soft spatula to remove the resin residue on the
build platform into the resin tank. Then, carefully detach the printed objects
from the build platform.
Washing
- Wash parts in an IPA bath with at least 98% purity. Best results are achieved when using a pre and post-wash. UWash ultrasonic cleaner is recommended for washing parts.
- Pre-wash bath: 1 minute. After use, if the IPA density increases by 5%, alternate clean IPA for this pre-washing step.
- Post-wash bath: 1 minute, always use clean IPA for each post-washing step.
- If necessary, a dedicated soft brush can be used to help remove residual resin.
Drying
Use compressed air to parts. If residual resin remains, repeat the “washing-
drying“ steps. Ensure parts dry thoroughly before post-curing.
Post-Curing
- Post-curing is a UV-LED light treatment to ensure that printed parts obtain optimal polymer conversion, decreasing the residual monomer of printed parts to a minimum and obtaining the required mechanical properties and surface properties.
- UCure, a post-cured device from UNIZ, is recommended to cure parts. Both the occlusal side and the other side are needed to be post-cured.
- One side: 1 minute, level 2, UCure
- The Other side: 1 minute, level 2, UCure
- If the printed part is supported, cure the non-supported side of the printed part at first, then remove supports by the same tools, and finally cure the supported side. Before use, the support stub needs to be ground and polished smoothly and be cleaned thoroughly.
Storage
Stored in a dark place where avoid direct sunlight or any kind of UV light,
the environment temperature is recommended around 15 to 28℃， and environment
humidity is less than 45%RH.
Do not use resin that exceeds the expiry date.
Disposal
Disposal of liquid resin waste under local regulations.
CONTACT
- UNIZ TECHNOLOGY LLC
- 9400 Activity Rd Ste L San Diego, CA 92126, US
- www.uniz.com.