WINCO TDM76-1 PTO Trailer Kit Instruction Manual
- June 25, 2024
- WINCO
Table of Contents
WINCO TDM76-1 PTO Trailer Kit
Product Specifications
- Model: TDM76 PTO Trailer
- Parts Included:
- Wheel
- Tongue Support
- Hitch Tongue Base
- Axle Shaft Support
- Decal
- Parts Bag
- Axle Protector
Installation Instructions
Required Tools
- Not Illustrated (NI)
- 43657-000
- 300081-1
- 300082
- 300083-1
- 300084-4
- 300085-1
- 300161-2
Parts Bag Contents:
- Part # : 636-000 –
- Description : 1/2 Split Lock Washer –
- Quantity : 13
- Part # : 1178-000 –
- Description : Flat Washer –
- Quantity : 4
Installation Steps
- Step 1: Assemble Wheel and Axle components.
- Step 2: Attach Hitch Tongue Base and Tongue Support.
- Step 3: Install Axle Shaft Support and Axle Protector.
FAQ
Q: What should I do after completing the assembly?
A: Cut out the Certificate of Completion provided in the manual and proudly
display it as a token of your
accomplishment.www.wincogen.com INSTALLATION
INSTRUCTIONS TDM76 PTO TRAILER
REQUIRED TOOLS:
WRENCH SIZES
- 1/2 INCH
- 1/4 INCH
| REF. # | PART # | DESCRIPTION | QTY. |
|---|---|---|---|
| 6 | 43657-000 | Wheel | 2 |
| 11 | 300081-1 | Tongue Support | 2 |
| 12 | 300082 | Hitch | 2 |
| 13 | 300083-1 | Tongue | 1 |
| 14 | 300084-4 | Base | 1 |
| 15 | 300085-1 | Axle | 1 |
| 16 | 300161-2 | Shaft Support | 1 |
| NI | 64006-000 | Decal | 1 |
| NI | TDM76-1 | Parts Bag | 1 |
| NI | 16343-000 | Axle Protector | 2 |
NI = Not Illustrated
PARTS BAG
REF. #
|
PART #
|
DESCRIPTION
| QTY IN PARTS BAG
---|---|---|---
1| 636-000| 1/2” Split Lock Washer| 13
2| 1178-000| Flat Washer| 4
3| 1744-000| 1/2” Hex Nut| 13
4| 16248-000| 1/4” Flange Nut| 4
5| 20979-000| Cotter Pin| 2
7| 48178-000| 1/2” x 1” Bolt| 8
8| 57580-002| 1/2” x 3 1/2” Bolt| 1
9| 57580-007| 1/2” x 3” Bolt| 4
17| 300163| U-Bolt| 2
STEP 1
Attach tongue supports (11) to the base (14) using the hardware provided (1,
3, 7). Place tongue (13) into the tongue supports (11) and attach using the
hardware provided. (1, 3, 7). Place hitch pieces (12) and tongue support (ref.
16) on the tongue (13) and attach using the hardware provided (9, 3, 1).
STEP 2
Slide the axle (15) through the holes in the base (14). Slide one washer (2)
onto each end of the axle. Lift the base and tongue assembly and slide the
wheels (6) on the axle. Place the cotter pins (5) through the axle and bend to
secure. Install the u-bolts (17) from the bottom around the axle. Secure from
the top with flange nuts (4). 
STEP 3
Place the generator on the base (14) and mount using the hardware provided (1,
3, 4). 
