YISSVIC WP2011 Electric Mosquito Racket User Manual
- June 15, 2024
- YISSVIC
Table of Contents
Electric Mosquito Swatter
User Manual
Model: WP2011
Dear Customer
Thank you for using YISSVIC Mosquito Swatter. To ensure safety and prolong the
service life of the product, please read this manual carefully before use, and
keep it in a safe place for future reference.
Cautions!
- When the electric mosquito swatter is working, there is high voltage on the metal mesh surface. Keep away from children. Beware of electric shock. Do not touch the metal mesh surface with your hands or holding metal objects.
- Do not use in flammable or explosive gases or liquids in the area, do not use metal and other conductive objects to touch the metal mesh surface.
- If not in use, ensure the power is off by pushing the switch to the bottom position.
- Do not clean with water or wipe with a wet towel, please keep the mosquito swatter dry to avoid damage to the internal electronic components.
- Do not let the product get wet or damp. When the climate is humid, the mosquito swatter may absorb moisture, which will reduce the mosquito killing effect. You should use a hair dryer to dry it in time or dry it in the sun.
- In order to ensure the service life of the battery, if there is no obvious effect of killing the mosquitoes during use, the battery voltage is already low at this time, please stop using it and charge it in time. Do not push the switch or touch the metal mesh surface when charging. The maximum charging time cannot exceed 12 hours. If you do not use it for a long time, recharge it every 3 months and place it in a dry place to prevent moisture.
- After killing the mosquitoes, use a small brush to clean up the residue on the metal mesh surface in time. Do not rinse with water to prevent short circuit.
- Only for indoor use, not applicable or stored in barns, livestock sheds, gas stations, explosive dust places.
- Please do not slap other hard objects or pinch the metal mesh surface to avoid damage to the metal mesh surface.
- It is forbidden to disassemble, impact, squeeze, or throw the battery into a fire. If there is severe expansion, do not continue to use it.
- The built-in rechargeable battery of the product contains substances that may pollute the environment. The battery should be disposed of at the official waste collection point.
- The battery of this mosquito swatter is a lithium battery. It can only be replaced by the factory or a qualified supplier. If you do not follow the instructions in this instruction, we will not be responsible for all losses or impacts caused by private replacement.
- This electric mosquito swatter must be charged with a DC power supply that strictly conforms to the rated voltage value. It is strictly forbidden to charge with other power supplies. We will not be responsible for problems caused by charging by replacing the power supply without permission.
Structure Description
- Double-layer Protective Nets
- Purple Attractant Light
- Working Indicator
- Charging Indicator
- Detachable Charging Base
- Auto ZAP Mode
- Manual ZAP Mode
- Power Off Button
- ZAP Button
Operation Instruction
Note:
- Do not touch the metal mesh within 3 to 5 seconds after “ZAP” to prevent electric shock.
- The swatter is in a discharge state when in “Auto ZAP Mode”, please do not touch the metal mesh to prevent electric shock.
- It is recommended to charge in “OFF” mode for fast charging.
- Do not touch the safety mesh with sharp and hard objects to avoid damage to the mosquito swatter.
Auto ZAP Mode:
Push the power switch to the “( **)” position, purple attractant lights is
on to attract mosquitoes, the swatter is ALWAYS in a discharge state and will
automatically kill mosquitoes in contact.
It is recommended to keep it charging when use this mode.**
Manual ZAP Mode:
Push the power switch to the “( ****)” position, press and hold the ZAP button
(the purple attractant light will be on), manually wave the swatter to kill
mosquitoes in contact.
Power Off:
Push the power switch to the “( ****)” position to turn off the swatter.
Working Indicator Instructions:
-
Indicator in Red:
The swatter is in a working status to kill mosquitoes by electric discharge.
(1) In Auto ZAP Mode, working indicators is always in Red.
(2) In Manual ZAP Mode, press ZAP button then working indicator will be in Red. -
Indicator is not lit:
The swatter is not in working status.
NOTE: Please do not touch the metal mesh when indicator is in Red to prevent electric shock.
Charging Instruction:
Connect the swatter to the charging base, and then connect the charging base to the plug and insert it into the socket. At this time, the swatter is in a charging status.
-
Charging Indicator in Red
Swatter is charging and it is not fully charged. -
Charging Indicator in Green
Swatter is charging and it is fully charged. -
Charging Indicator is not lit
Swatter is not charging.
Specifications
| Model | WP2011 |
|---|---|
| Rated Power | 5W |
| Rated Voltage | 5V ⎓ 1A |
| Output Voltage | DC4000V |
| Battery Capacity | 1200mAh |
| Charging Time | 4h |
Troubleshooting
If below solutions cannot solve your problems, please contact seller.
| Problems | Solutions |
|---|---|
| 1. No Charging Base | It is packed separately in the box, please check |
carefully.
2. Keep zapping even nothing is on it| There is a touch between the inner 2
metal mesh, which triggering zapping. Please check the whole metal mesh and
separate them.
3. Auto Mode did not work| Please charge the swatter on Manual or OFF mode
for at least 2 hours before using the Auto Mode. Because the auto mode needs
much more battery to start working.
4. Purple light did not turn on| The light might be damaged during
transportation, or it is in low battery. Please charge in OFF mode.
5. Did not charge| The mosquito swatter you received may be out of battery or
in low battery for safety transportation. Please charge for 12 hours before
first use to activate the battery. Remember to charge it in OFF or Manual
mode.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Do not dispose of the appliance as unsorted municipal waste, use a separate recycling facility. Contact your local government to find out about the current recycling system. If the appliance is sent to a landfill or dump, hazardous materials may seep into the groundwater and then into the food chain, harming your health!