Losi LOS01026T1 MINI LMT Scale 4 WD Monster Truck Instruction Manual

: June 15, 2024
: Losi

Losi LOS01026T1 MINI LMT Scale 4 WD Monster Truck

Product Information

Specifications

Scale: 1/18th
Drive Type: 4WD
Model Number: LOS01026T1/T2

Product Usage Instructions

Register Your Losi Product Online
Register your vehicle now and be the first to find out about the latest option parts, product updates, and more. Click on the Support tab at www.LOSI.com and follow the product registration link to stay connected.

Components
The Mini LMT 1/18th Scale 4WD Monster Truck includes the following components:

A water-resistant vehicle with waterproof electronics
Recommended accessories
Tools included

Water-Resistant Vehicle with Waterproof Electronics

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many wet conditions, including puddles, creeks, wet grass, snow, and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and should not be submerged. The Electronic Speed Control (ESC), servo(s), and receiver are waterproof, but most of the mechanical components are water-resistant and should not be submerged.

CAUTION:
Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

Wet Conditions Maintenance
After operating the vehicle in wet conditions, it is important to perform the following maintenance steps:

Remove the battery from the vehicle.
Clean off any dirt, mud, or moisture from the vehicle using a soft cloth or brush.
Dry the vehicle thoroughly using a towel or air drying.
Apply a light coat of silicone spray or similar water displacement product to the mechanical components to help prevent corrosion.

CAUTION:
Always keep hands, fingers, tools, and any loose or hanging objects away from rotating parts when performing the above drying technique.

General Precautions
It is important to follow these general precautions while using the Mini LMT:

Never use a pressure washer to clean your vehicle.
Avoid exposing the vehicle to extreme temperatures.
Avoid operating the vehicle near flammable materials.
Always operate the vehicle in a safe and open area.

Quick Start
Follow these steps to quickly get started with your Mini LMT:

Read the safety precautions found in this manual.
Charge the battery. Refer to the included charging warnings and instructions for battery charging information.
Install AA batteries in the transmitter. Only use alkaline or rechargeable batteries.
Install a fully charged battery in the vehicle.
Power ON the transmitter and then the vehicle. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.
Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.

FAQ

Q: Can I use the Mini LMT in water?
A: The Mini LMT is highly water-resistant but not completely waterproof. While you can operate it in wet conditions, it should not be submerged.
Q: How should I clean the Mini LMT after using it in wet conditions?
A: After operating the vehicle in wet conditions, remove the battery, clean off any dirt or moisture, dry the vehicle thoroughly, and apply a light coat of silicone spray to prevent corrosion.
Q: Can I use a pressure washer to clean the Mini LMT?
A: No, you should never use a pressure washer to clean your vehicle.

NOTICE
All instructions, warranties, and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

WARNING:
Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

SAFETY PRECAUTIONS AND WARNINGS

Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
Always operate your model in open spaces away from full-size vehicles, traffic and people.
Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
Always keep all chemicals, small parts and anything electrical out of the reach of children.
Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics.
Never place any portion of the model in your mouth as it could cause serious injury or even death.
Never operate your model with low transmitter batteries.

REGISTER YOUR LOSI PRODUCT ONLINE

Register your vehicle now and be the first to find out about the latest option parts, product updates and more. Click on the Support tab at www.LOSI.com and follow the product registration link to stay connected.

COMPONENTS

Losi® Mini LMT RTR 4WD Monster Truck (Gravedigger / Son-uva digger)
Spektrum® 2-CH 2.4GHz Transmitter (SPMRSLT320)
Spektrum ESC/Receiver 2.4GHz: 1/18 (SPMXSE3025RX)
Losi 25T Brushed 380 Size Motor (LOS11002)
Spektrum SX108 Micro Metal Gear Servo (SPMSSX108)
Spektrum 7.4V 810mAh 2S LiPo Hardcase: IC2 (SPMX812SH2)
Smart G2 2s LiPo (IC2) USB-C Charger (SPMXC0040)
4 AA batteries (for transmitter)

RECOMMENDED ACCESSORIES

Soft bristle brush for cleaning
Startup Tool Set: Metric (DYN2834)
Thread Lock

TOOLS INCLUDED

4-Way Wrench
Misc. tools

Use only Dynamite® tools or other high-quality tools. Other tools can cause damage to the small screws and parts used on this model.

PACKAGE CONTENTS

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain. While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, how-ever, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.

CAUTION:
Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

GENERAL PRECAUTIONS

Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.
Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation.
Never operate your transmitter or vehicle where lightning may be present.
Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water
is very conductive and highly corrosive, so use caution.
Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.
Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE
Drain any water that has been collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed.

CAUTION:
Always keep hands, fingers, tools, and any loose or hanging objects away from rotating parts when performing the above drying technique.

Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.
Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.
Spray the bearings, drive train, fasteners, and other metal parts with a water-displacing light oil. Do not spray the motor.
Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
Increase the frequency of disassembly, inspection, and lubrication of the following:
- Front and rear axle hub assembly bearings.
- All transmission cases, gears, and differentials.
- Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

QUICK START
Please read the entire manual to gain a full understanding of the Mini-LMT vehicle, fine-tuning the setup and performing maintenance.

Read the safety precautions found in this manual.
Charge the battery. Refer to the included charging warnings and instructions for battery charging information.
Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries.
Install a fully charged battery in the vehicle.
Power ON the transmitter and then the vehicle. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.
Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.
Drive your vehicle.
Perform any necessary maintenance.

CHARGING

CHARGING WARNINGS

CAUTION:
All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fire, personal injury and/or property damage.

NEVER LEAVE CHARGING BATTERIES UNATTENDED.
NEVER CHARGE BATTERIES OVERNIGHT.
By handling, charging or using the included Li-Po battery, you assume all risks associated with lithium batteries.
If at any time the battery begins to balloon or swell, discontinue use immediately. If charging or discharging, discontinue and disconnect. Continuing to use, charge or discharge a battery that is ballooning or swelling can result in fire.
Always store the battery at room temperature in a dry area for best results.
Always transport or temporarily store the battery in a temperature range of 40–120º F (5–49° C).
Do not store battery or model in a car or direct sunlight. If stored in a hot car, the battery can be damaged or even catch fire.
Always charge batteries away from flammable materials.
Always inspect the battery before charging.
Always disconnect the battery after charging, and let the charger cool between charges.
Always constantly monitor the temperature of the battery pack while charging.
ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO BATTERIES. Failure to charge the battery with a compatible charger may cause a fire resulting in personal injury and/or property damage.
Never discharge Li-Po cells to below 3V under load.
Never cover warning labels with hook and loop strips.
Never charge batteries outside recommended levels.
Never charge damaged batteries.
Never attempt to dismantle or alter the charger.
Never allow minors to charge battery packs.
Never charge batteries in extremely hot or cold places (recommended between 40–120°F or [5–49° C]) or place in direct sunlight.

CHARGING THE BATTERY

NOTICE: Charge only batteries that are cool to the touch and are not damaged. Inspect the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured.
CAUTION: Only use chargers specifically designed to charge the included Li-Po battery. Failure to do so could result in fire, causing injury or property damage.
CAUTION: Never exceed the recommended charge rate.

Use only the included USB charger to charge the battery.

Connect the included USB-C power cable to the charger. The charger will work with most 5V mobile power sources or smartphone chargers with at least 1 amp of power output.
NOTICE: Charging the battery with a USB power port with less than 1 amp of power output can produce heat.
Connect the IC2 connector on the battery to the charger, noting correct polarity. Charging a fully discharged battery takes approximately 45–60 minutes. Charge times may vary depending on the power source.
Disconnect the battery from the charger when the charging cycle is complete.
Disconnect the power supply from the charger.

CAUTION:
Once charging is complete, immediately remove the battery. Never leave a battery connected to the charger.

Charger LED Indications

RED / GREEN, flashing = Charger ready
GREEN, flashing = Charging
GREEN, solid = Charging complete
RED, Solid = Charging error

SLT2 TRANSMITTER

Steering Wheel Controls the direction (left/right) of the model
The throttle Trigger Controls the speed and direction (forward/brake/reverse) of the model
Power Button Turns the power ON/OFF
Steering (ST-R) Servo Reversing Reverses the steering channel
Throttle Limit Limits throttle output to 50/75/100% Select 50% or 75% for less experienced drivers or when you are driving the vehicle in a small area
Indicator Lights
- Solid red light—Indicates radio connectivity and adequate battery power
- Flashing red light—Indicates the battery voltage is critically low. Replace the batteries
Steering Rate Adjusts the steering endpoints
Steering Trim Adjusts the steering center point

INSTALLING THE TRANSMITTER BATTERIES

This transmitter requires 4 AA batteries.

Remove the battery cover from the transmitter.
Install the batteries as shown.
Install the battery cover.

CAUTION: Never remove the transmitter batteries while the model is powered ON. Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

UNLOCKING THE BODY LATCHES

There are three twist lock body latches you can access from the front bottom.
Rotate the twist lock connectors to align with the slot.

INSTALLING THE BATTERY AND POWERING ON THE VEHICLE

Raise the body to access the battery tray.
Install the fully charged battery in vehicle.
Secure the battery with the elastomer straps.
Power on the transmitter.
Connect the battery to the ESC/receiver.
Power on the ESC/receiver.
Lower the body and secure it with the twist locks.

CONTROL TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the vehicle is powered ON, adjust the Throttle Trim until they stop. To make the wheels move forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.

When moving forward, the wheels should maintain a straight line without any steering wheel input. If not, adjust the Steering Trim, so the wheels maintain a straight line without having to turn the steering wheel.

DRIVING PRECAUTIONS

ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off.
Maintain sight of the vehicle at all times.
Inspect the vehicle for loose wheel hardware.
Inspect the steering assembly for any loose hardware. Driving the vehicle off-road can cause fasteners to loosen over time.
ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result.
Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.
Stop driving the vehicle when you notice a lack of power. Driving the vehicle when the battery is discharged can cause the receiver to power off. You may lose control of the vehicle.
Do not apply the throttle in forward or reverse if the vehicle is stuck. Applying throttle in this instance can damage the motor or ESC.
After driving the vehicle, allow the electronics to cool to ambient temperature before using the next battery pack.

RUN TIME
Average run times is approximately 10-12 minutes with the included 810 mAh Spektrum 2s LiPo battery. The condition of a battery pack is also an important factor in both run time and speed. The battery connectors may become hot during driving. Batteries will lose performance and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Properly seating the motor brushes will increase the life and performance of the motor.
Keep your vehicle clean and well-maintained.
Allow more airflow to the ESC and motor.
Change the gearing to a lower ratio. A lower ratio lowers the operating temperature of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

TUNING, ADJUSTING, AND MAINTAINING THE VEHICLE

Examine your vehicle regularly.
Use a brush to remove dirt and dust.
Look for damage to the axle housings and other molded parts.
Re-glue the tires to the wheels, if necessary.
Use suitable tools to tighten fasteners.
Make sure the 4-link bars, rod ends, and steering linkages are not bent. Replace any bent linkages.
Remove the shocks and inspect them for damage. Rebuild the shocks if oil is leaking.
Inspect electronics and batteries for exposed wires. Repair exposed wires with shrink-wrap or replace the wire.
Make sure the ESC and receiver are secure on the chassis. Replace the double-sided tape, if necessary.
Power on your transmitter. If the red light is flashing, replace the AA batteries in the transmitter.

SERVICE/REPAIR

RADIO/SPEED CONTROL AND MOTOR
If any problems other than those covered in the troubleshooting section arise, please call the appropriate electronics service department. They will be able to give the problem additional specific attention and provide instructions for the solution.

MAINTENANCE
If any questions other than those covered in the troubleshooting or maintenance sections arise, please call the appropriate Horizon product support department.

CLEANING
Performance can be hindered if dirt gets in any of the moving suspension parts. Use compressed air, a soft paintbrush, or a toothbrush to remove dust or dirt. Avoid using solvents or chemicals as they can actually wash dirt into the bearings or moving parts, as well as cause damage to the electronics.

SHOCK CLEANING

Oil-filled shocks will require regular maintenance due to the oil breaking down or getting dirty. This maintenance should be performed after about every 3–5 hours of use, depending on the driving conditions.

Remove the shock from the vehicle.
Remove the bottom cartridge from the shock body and dispose of fluid.
Disassemble the shock. Clean thoroughly with a plastic- and electronic-safe degreaser (DYN5500). Dry parts before assembly.
Re-assemble the shock and refill the shock body with silicone fluid (17.5 weight recommended, TLR74001).
Slowly move the shaft and piston up and down to remove air bubbles.
Move the piston to the midway point of the body and install the bottom cartridge.
Wipe off any overflowing fluid.
Re-install the shock on the vehicle.

ADJUSTING RIDE HEIGHT
Chassis Ride height is an adjustment that affects the way the vehicle jumps, turns and goes over bumps. Drop the vehicle from approximately 6 inches (152mm) in height on to a flat surface. When dropping the vehicle, watch how the chassis settles. Make sure that the lower 4-link bars are almost level to the flat surface.

Lowering the chassis ride height where the 4-link bars are below level will increase steering, but increase weight transfer and can cause the truck to become edgy. Raising the chassis ride height where the 4-link bars are above level will increase the ability of the suspension to absorb bigger jumps and obstacles, but raises the overall center of gravity and can make the truck more prone to flip under power.

BINDING
Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below:

Disconnect the steering servo from the 2n1 unit.
Insert the BIND plug into the steering channel.
Connect a fully charged battery to the ESC.
Power on the ESC
Power ON the transmitter. The receiver’s red LED will turn solid when the bind is successful.
Power OFF the ESC to save the settings.
Power of the transmitter.
Remove the BIND plug and re-connect the steering servo.

You must rebind when binding the receiver to a different transmitter.

NOTICE:
Do not attempt to bind the transmitter and receiver if there are other compatible transmitters in bind mode within 400 feet. Doing so may result in unexpected binding.

TROUBLESHOOTING GUIDE

PROBLEM	POSSIBLE CAUSE	SOLUTION

The vehicle does not operate

| The battery not charged or plugged in| Charge battery/plugin
ESC switch not “On”| Turn on the ESC switch
Transmitter not “On” or low battery| Turn on/replace batteries

The motor runs but the rear wheels do not rotate

| The pinion not meshing with the spur gear| Adjust pinion/spur mesh
Pinion spinning on motor shaft| Tighten pinion gear setscrew on motor shaft flat spot
Transmission gears stripped| Replace transmission gears
Drive pin broken| Check and replace the drive pin

Steering does not work

| The servo plug not in the receiver properly| Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity
Servo gears or motor damaged| Replace or repair servo
Will not turn in one direction| Servo gears damaged| Replace or repair servo

The motor does not run

| The motor wire solder joint is damaged| Resolder the motor wire with the proper equipment
Motor wire broken| Repair or replace as needed
ESC damaged| Contact Horizon Hobby Product Support

ESC gets hot

| Motor over-geared| Use a smaller pinion or larger spur gear
Driveline bound up| Check wheels and transmission for binding

Poor run time and/or sluggish acceleration

| The battery pack not fully charged| Recharge battery
The charger not allowing full charge| Try another charger
Driveline bound up| Check wheels, and transmission for binding

Poor range and/or glitching

| Transmitter batteries low| Check and replace
Vehicle battery low| Recharge battery
Loose plugs or wires| Check all wire connections and plugs

PARTS LISTINGS

PART #|
---|---
LOS11002| 25T Brushed 380 Size Motor
LOS210042| DriverInsert&SafetySeat:Mini LMT
LOS210043| BodyButton Set, Complete: Mini LMT
LOS210044| BodySet, GraveDigger, Pntd: Mini LMT
LOS210045| BodySet,GraveDigger,Clr:Mini LMT
LOS210046| BodySet,SonUvaDigger,Pnt:Mini LMT
LOS210047| BodySet,SonUvaDigger,Clr:Mini LMT
LOS210048| LED Front Headlight Set: Mini LMT
LOS210049| Grill Set, Son Uva Digger: Mini LMT
LOS211042| Battery&Radio Tray Set: Mini LMT
LOS211043| Servo Saver Set: Mini LMT
LOS211044| Suspension Mounting Set:Mini LMT
LOS211045| Wheelie Bar Set, Green: Mini LMT
LOS211046| Wheelie Bar Set, Blue: Mini LMT
LOS211047| Chassis Cross Brace Set:Mini LMT
LOS211048| 4-In-1 Header Set(L/R): Mini LMT
LOS211049| Cage Set Complete,Green:Mini LMT
LOS211050| Cage Set Complete,Blue: Mini LMT
LOS211051| SteeringTieRod&DragLink:Mini LMT
LOS211052| Chassis Plate Set,Green:Mini LMT
LOS211053| Chassis Plate Set,Blue: Mini LMT
LOS212035| Axle Housing Set: Mini LMT
LOS212036| Uppr 4-lnk Mnt&SrvoPlt: Mini LMT
LOS212037| CntrGearboxSet w/Covers:Mini LMT
LOS212038| CntrSliderDriveshaftSet:Mini LMT
LOS212039| CntrSliderDriveshaft(2):Mini LMT
LOS212040| CntrDrvshaftScrewpin(10):Mini LMT
LOS212041| Idle&CushDrive GearSet: Mini LMT
LOS212042| 37T RingGear,CntrSpool: Mini LMT
LOS212043| Spool, Center Gear Box: Mini LMT
LOS212044| Diff Complete (F/R): Mini LMT
LOS212045| 13T Pinion Gear, Center:Mini LMT
LOS212046| 13T Pinion Gear, Axle: Mini LMT
LOS212047| Rear Axle Shaft (2): Mini LMT
LOS212048| Rear Dogbone (2): Mini LMT
LOS212049| Fr Universal Set (2): Mini LMT
LOS212050| 12mm Hex & Screwpin(4): Mini LMT
---|---
LOS212051| WheelHex Screwpins(10): Mini LMT
LOS212053| Pinion 15T,0.5m,2mmShaft:Mini LMT
LOS213010| Shock Set Complete (2): Mini LMT
LOS213011| ShckCartRebuildKit(4): Mini LMT
LOS213012| Shock Shaft Rebuild (2):Mini LMT
LOS213015| Shock Springs Soft, Yellow (4): Mini LMT
LOS213016| Shock Springs Med, Blue (4): Mini LMT
LOS213017| Shock Springs Firm, Red (4):Mini LMT
LOS214041| Spindle & Carrier Set: Mini LMT
LOS214042| Sway Bar Set (F/R): Mini LMT
LOS214043| Rr Axle Mount Set,0 deg:Mini LMT
LOS214044| Upper 4-link Bar Set(4):Mini LMT
LOS214045| Lower 4-link Bar Set(4):Mini LMT
LOS214046| King Pin Set (4): Mini LMT
LOS214047| 4-Link Rod Ends and Pivot Balls (16): Mini LMT
LOS215001| Cap Head Screws, M2x8mm (10)
LOS215002| Flat Head Screws, M2x8mm (10)
LOS215003| Flat Head Screws, M2x12mm (10)
LOS215004| Button Head Screws, M2x5mm (10)
LOS215005| Button Head Screws, M2x8mm (10)
LOS215006| Button Head Screws, M2x10mm (10)
LOS215007| Button Head Screws, M2x14mm (10)
LOS215008| Button Head Screws, M2x16mm (10)
LOS215009| Button Head Screws, M2x20mm (10)
LOS215010| Cap Head Screws, M2x25mm (10)
LOS216008| Washer, 2.2mm x 4.5mm x 0.3mm (10)
LOS216009| E-Clip and Shim Set: Mini LMT
LOS217002| 5x8x2.5mm BB, Flanged(4):Mini LMT
LOS217003| 7x13x3mm BallBearing(4):Mini LMT
LOS235014| “Lock Nut, M2 x 0.4 x4mm (10)”
LOS235029| M2 x 4mm Cap Head Screws (10)
LOS257007| 4 x 8 x 3mm Ball Bearing (4)
LOS41042| Monster Truck Tire(L/R):Mini LMT
LOS41043| Foam Tire Insert (2): Mini LMT
LOS41044| Whl,Grn Beadlock,Gry(2):Mini LMT
LOS41045| MT,GrnBeadlock,Prmntd(2):Mini LMT
LOS41046| Whl,BlueBeadlock,Gry(2):Mini LMT
LOS41047| MT,BluBeadlock,Prmntd(2):Mini LMT
LOS75001| Super Tacky Diff Grease
LOSB3008| 3x6x2.5mm Ball Bearing (2)
SPMRSLT320| SLT3 3CH 2.4Ghz with SLR300 RX
SPMSSX108| SX108 Micro Gear Servo
SPMX812SH2 SPMXC0040 SPMXSE3025RX

TLR245008

TLR245011 TLR245016

TLR255003

TLR5913 TLR5914 TLR5960

TLR74001

| 810mAh 2S 7.4V Smart G2 LiPo: I S10 G2 2S USB-C Charger w/ IC2 SLT 25a ESC/RX 1/16 & 1/18, IC2

Cap Head Screws, M2x10mm (10)

Button Head Screws, M2x6mm (10) M3 Flanged Lock Nuts (10)

Cap Head Screws, M2.5x6mm (10)

ButtonHeadScrews,M2.5 x 12mm(10) Button Head Screws,M2 x 12mm(10) Flathead Screws, M2 x 6mm (10)

Silicone Shock Oil, 17.5wt,150CST, 2oz

---|---

OPTIONAL PARTS

PART #|
---|---
DYN2511| Curved Body Scissors
DYN2516| Straight Body Scissors
DYNT2010| Machined Nut Driver Set (4) Metric
DYNT2030| Machined Hex Driver Set (4) Met
LOS212052| Pinion 14T,0.5m,2mmShaft:Mini LMT
LOS212054| Pinion 16T,0.5m,2mmShaft:Mini LMT
LOS31004| Body Buttons Aluminum, Green (10): Mini LMT
LOS31005| Body Buttons, Aluminum, Blue (10): Mini LMT
LOS311020| Steering Tie Rod, Aluminum, BLK: Mini LMT
LOS311014| Body Mount Cross Bar, Aluminum, BLK (2): Mini LMT
LOS311015| Crossbar, Center, Top, Aluminum, BLK: Mini LMT
LOS311016| Crossbar, Shock Mount, Aluminum, Blk (2): Mini LMT
LOS311017| Hoop Crossbar, Aluminum, Blk (2): Mini LMT
LOS311018| Servo Arm, Aluminum, Blk: Mini LMT
LOS311019| Wheelie Bump, Aluminum, BLK: Mini LMT
LOS312008| Axle Housing Set, Aluminum, Black: Mini LMT
LOS312009| Axle Mount Rear, 0deg, Aluminum, Blk: Mini LMT
LOS314006| Lower 4-link Mount Set, Aluminum, Black (4): Mini LMT
LOS314007| Steering Spindle Set, Aluminum, Black: Mini LMT
LOS314008| Spindle Carrier Set, 0deg, Aluminum, Blk: Mini LMT
LOS314010| Upper 4-link Mount, Aluminum, Black: Mini LMT
LOS314012| Spindle Carrier Set, 5deg, Aluminum, Blk: Mini LMT
LOS70000| LOSI Foam Pit Mat, 24″”x 68
LOSB1107| Course/Track Cones,Orng 2.75 (6)
DYNT2030| Machined Hex Driver Set (4pc) Metric
DYNT2010| Machined Nut Driver Set (4pc), Metric
SPMX652SH2| 650mAh 2S 7.4V Smart G2 LiPo; I
SPMXC2020| Smart S1200 G2 AC Charger; 1×200
SPMXCA320| Adapter: IC3 Batt / IC2 Dev 6
---|---
SPMXCA400| Smart Lipo Bag, 14 x 6.5 x 8 cm
TLR31003| Shock Set, Aluminum (4): Mini LMT
TLR314009| Lower Shock Mount, Aluminum, Black (4): Mini LMT
TLR314010| Upper shock Mount, Aluminum, Black (4): Mini LMT
TLR74000| SIL SHOCK OIL,15WT,104CST,2OZ
TLR74002| SIL SHOCK OIL,20WT,195CST,2OZ
TLR74003| SIL SHOCK OIL,22.5WT,223CST,2OZ
TLR74004| SIL SHOCK OIL,25WT,250CST,2OZ
SPMSSX117| SX117 Micro Servo Metal Gear/Ca
SPMXC2050| Smart S155 G2 AC 1x55W Charger
SPMX6502SH2| 650mAh 2S 7.4V 30C LiPo;
SPMX8102SH2| 810mAh 2S 7.4V 50C LiPo;
TLR336005| M3 Flanged Aluminum Lock Nuts, Black (10)
TLR76009| TLR Lok Threadlock Blue
TLR77000| High-Pressure Black Grease

EXPLODED VIEW

LIMITED WARRANTY

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 2 years from the date of purchase.

What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup, or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, the purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law
These terms are governed by Illinois law (without regard to conflict of law principles). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you if you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll-free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.

Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/service-center_render- service-center. If you do not have internet access, please contact Horizon Product Support to obtain an RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending the product to Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are written on the outside of the shipping carton.

NOTICE:
Do not ship Li-Po batteries to Horizon. If you have any issues with a Li-Po battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition, you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content /service-center_render-service-center.

ATTENTION:
Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un- serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

WARRANTY AND SERVICE CONTACT INFORMATION

COUNTRY OF PURCHASE| HORIZON HOBBY| CONTACT INFORMATION| ADDRESS
---|---|---|---
| Horizon Service Center (Repairs and Repair Requests)| servicecenter.horizonhobby.com/RequestForm/|
United States of America| Horizon Product Support (Product Technical Assistance)| [email protected] 800-338-4639| 2904 Research Rd Champaign, Illinois, 61822 USA
| Sales| [email protected] 888-338-4639|
EU| Horizon Technischer Service Sales: Horizon Hobby GmbH| [email protected]

+49 (0) 4121 2655 100

| Hanskampring 9 D 22885 Barsbüttel, Germany

FCC INFORMATION

FCC ID: BRWWACO1T

Supplier’s Declaration of Conformity

LOS Mini LMT: 1/18th Scale 4WD Monster Truck (LOS01026T1/T2) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Contact

Horizon Hobby, LLC 2904 Research Rd.,
Champaign, IL 61822
Email: [email protected]
Web: HorizonHobby.com.

IC INFORMATION

CAN ICES-3 (B)/NMB-3(B)
IC: 6157A-SPMSLT200F

This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation,

Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following 2 conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

EU Compliance Statement:
Hereby, Horizon Hobby, LLC declares that the device complies with the following: Low Voltage Directive (LVD) 2014/35/EU, 2014/30/EU EMC Directive, Radio Equipment Directive (RED) 2014/53/EU, RoHS 2 Directive 2011/65/EU, RoHS 3 Directive – Amending 2011/65/EU Annex II 2015/863 The full text of the EU declaration of conformity is available at the following internet address: https://www.horizonhobby.com/content/support-render-compliance.

Wireless Frequency Range and Wireless Output Power:

Transmitter:

2410–2480MHz
23.23 dBm

Receiver:

2404–2476MHz
5.58dBm

EU Manufacturer of Record:
Horizon Hobby, LLC 2904 Research Road Champaign, IL 61822 USA

EU Importer of Record:
Horizon Hobby, GmbH Hanskampring 9 22885 Barsbüttel Germany

WEEE NOTICE:
This appliance is labeled per European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

468669.1
Updated 7/2023 | LOS01026T1/T2
©2023 Horizon Hobby, LLC.
Losi, Dynamite, IC2, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks and logos are the property of their respective owners.

Scan the QR code and select the Manuals and Support quick links from the product page for the most up-to-date manual information.