PITTSBURGH 63586 6 Inch Composite Digital Caliper Owner’s Manual
- October 30, 2023
- PITTSBURGH
Table of Contents
6″ Composite Digital Caliper
63586 6 Inch Composite Digital Caliper
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions,
assembly, operating, inspection, maintenance and cleaning procedures. Write
the product’s serial number in the back of the manual near the assembly
diagram (or month and year of purchase if product has no number). Keep this
manual and the receipt in a safe and dry place for future reference.
63586
Visit our website at: http://www.harborfreight.com
Email our technical support at:
productsupport@harborfreight.com
When unpacking, make sure that the product is intact and undamaged. If any
parts are missing or broken, please call 1-888-866-5797 as soon as possible.
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
© Copyright 2023 by Harbor Freight Tools ® Diagrams within this manual may not
be drawn proportionally. Due to continuing improvements, actual product may
differ slightly from the product described herein.
Tools required for assembly and service may not be included.
WARNING
Read this material before using this product. Failure to do so can result
in serious injury. SAVE THIS MANUAL.
Specifications
Display Units | Inches & Millimeters |
---|---|
Accuracy | ±0.01″ (0.2mm) |
Display | 0.01″ (0.3mm) |
Power Supply | 1.5V LR44 (Included) |
Important Safety Information
- Wear ANSI-approved safety goggles during use.
- Keep work area clean and well lit.
- Do not operate when tired or when under the influence of alcohol, drugs or medication.
- Use as intended only.
- Inspect before every use; do not use if parts are loose or damaged.
- Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
Button/Coin Battery Warnings
WARNING
INGESTION HAZARD:
This product contains a button cell or coin battery.
This symbol means:
INGESTION HAZARD: This product contains a button cell or coin battery.
- Immediately dispose of used batteries and keep away from children. Do NOT dispose of batteries in household trash.
- Even used batteries may cause severe injury or death.
- Call a local poison control center for treatment information.
- Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
- Ensure the batteries are installed correctly according to polarity (+ and -).
- Remove and immediately discard batteries from equipment not used for an extended period of time.
- Non-rechargeable batteries are not to be recharged.
- Do not force discharge, recharge, disassemble, heat above 122°F or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
Components and Controls
Instructions
-
Remove pull tab from battery compartment before use.
-
Push the OFF ON button to turn caliper on.
-
To toggle measurement between inches and millimeters, press in/mm button.
-
With jaws closed, press ZERO to set readout to 0.
-
To measure outside of object, set the bottom prongs outside object being measured. Slide the jaws together until they gently contact the item.
Figure A: Outer Measurement -
To measure inside of object, set the top prongs inside object being measured. Spread prongs apart until they touch surface of object. Figure B: Inner Measurement
-
To measure an object’s step, place the sliding jaw on the upper step of the workpiece, then spread the prongs apart until the fixed jaw contacts the lower step. Figure C: Step Measurement
-
When finished, press OFF ON button to turn off Caliper.
-
To replace battery, remove screw(s) and open battery compartment. Install new LR44 battery in correct polarity, close compartment and replace screw(s).
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase
instead.
Note: Replacement parts are not available for this item. Refer to UPC
193175508577.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no
event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our
product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we
may elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
26677 Agoura Road · Calabasas, CA 91302 · 1-888-866-5797
Documents / Resources
|
PITTSBURGH 63586 6 Inch Composite Digital
Caliper
[pdf] Owner's Manual
63586 6 Inch Composite Digital Caliper, 63586, 6 Inch Composite Digital
Caliper, Composite Digital Caliper, Digital Caliper, Caliper
---|---
|
PITTSBURGH 63586 6 Inch Composite Digital
Caliper
[pdf] Owner's Manual
63586, 63586 6 Inch Composite Digital Caliper, 6 Inch Composite Digital
Caliper, Composite Digital Caliper, Digital Caliper, Caliper
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>