ANRAN F1 Pro 2K 3G/4G LTE Solar Battery Security Camera User Guide

F1 Pro Solar powered wireless security camera
Quick Start Guide

What’s Included

Solar Panel

Product Overview

CAUTION: Please insert the Micro SD Card according to the direction shown in the diagram. Micro SD Card might JAM if inserted incorrectly and device could be damaged.
SD Card Port: Support micro SD card for local storage (Max 128GB).
Reset button: Used to restore the camera to factory settings (Press and hold on 5-8s).
Card capacity requirements: 8-128GB.
Read and write speed requirements: class10 level
File format: FAT32.

APP Installation and Account Registration

3.1 Download “ANRAN”APP
Method 1: Download “ANRAN” APP from APP Store (iOS) or Play Store (Android);
Method 2: Scan “ANRAN”APP QR code to download it.

|
---|---
https://apps.apple.com/us/app/anran/id1611278380| https://play.google.com/store/apps/details?id=com.anran.arcloud&hl=zh- CN

Tips: Please turn on 2 permissions below when use this APP at the first time.

1. Allow “ANRAN” APP data and wireless LAN, or it will be failed to add IP to access mobile cellular camera.
2. Allow” ANRAN “APP to receive pushed message, or the cellphone will not receive alarm push when motion detection or audible alarm is triggered.

3.2 Register Account
New users need to register by e-mail, click “Register”, and follow the steps to complete the registration of the account, then log in.
Note:

• When registering a new account, please choose the region which you are actually in. (Different registered regions can’t share the camera.)
• lease choose to register by e-mail.

How to Add Camera to APP

Warming Tip: Please insert the Micro SD card before power on, otherwise, the SD card can not be detected.
4.1 Power on Camera

• Please long press the power button for 5s o power the camera.
• The indicator with red light blinking slowly means the camera is started successfully.

4.2 Connect the Camera
Put the camera and smart phone 1 to 3 feet (30 to 100 cm) away from the router to set Wi-Fi.

Warming Tip:

•  The camera only supports 2.4GHz Wi-Fi, and doesn’t support 5GHz WIFI.
• Please ensure that the Wi-Fi signal strength is to be over than 85%; if the camera is far away from the signal source , it won’t be connected successfully for the first time.

Wi-Fi Connection Steps:

|
---|---

Mounting the Camera

Find a Good Mounting Spot
To find a spot to mount Camera, you need to test wireless signal strength.

1. Open the ANRAN App, go to Camera Settings > Mounting Guide.
2.  To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera
3. Move the camera as close to the Wi-Fi Router as possible to get a better signal.

Select Height and location
Hang the camera 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of the camera. Avoid placing the camera under direct sunlight.

Installation instruction of solar panel

1. keep the installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
2. The installation between the solar panel and the camera is shown in the following figure(open up the silicone cover at the bottom of the camera, remove the small center part of the cover, insert the power cord through the opening and plug it into the Type- port and then close the cover taking up any slack in the power cord from the solar panel).

Tips for the installation of solar panel

1. When installing in the northern hemisphere, face the panel to the south, and when installing in the southern hemisphere, face the panel to the north.
2. Take care to install the solar panel so that the sun is not blocked by any items such as eaves, trees branches, etc.

Test the Wi-Fi signal at installation position
Use cell phone to test Wi-Fi signal quality at the installation position before installing camera, make sure the Wi-Fi router can provide good Wi-Fi signal.

Installation

1. Drilling according to position sticker, drill bit: 15/64″(6 mm).
2. Insert the plugs.
3. Tighten the screws.

What is required:

Wall Mount

Upside-down Mount

Installation instruction of solar panel
Place Solar Panel in an area with consistent sunlight throughout the year. It only needs a few hours of direct sunlight each day to keep your camera powered.
The amount of energy that the solar panel produces is affected by weather conditions, seasonal changes, geographic location, etc.

1. Fix the base to your mounting location using the included screws. If the installation surface is soft or unstable, first use a  6.0 drill bit to drill a hole in the wall, then insert the anchor nail into the hole, and fix the base with screws.
2. First, install the locking screw cap into the universal joint and then screw the circular socket nut into the universal joint.
3. Screw the universal joint into the back of the solar panel. Tighten it firmly with the attached nut.
4. Screw the locking screw cap into the base. Make sure that the universal joint is angled upward.
5. When adjusting the solar panel left or right, loosen the locking screw cap, turn the sleeve rod, and tighten the locking screw cap when the panel is in position.
6. Solar panel’s angle can be adjusted up and down up to 90°.

Tip: After the installation is complete, please check that all locking mechanisms are tightly secured.

PIR Motion Detection Settings

Enter the application – “Parameter Setting” – “Motion Detection” interface.

Warm Tips:

• When you encounter the missed or delayed alarm frequently in using this camera, you can adjust the motion detection sensitivity to solve them.
• If you notice the poor performance of motion detection in the nigh “Night Detection”. environment, fry for turn off

Product Specification

FAQs

1. The device prompts offline?

• Check whether the equipment is in the power-on state, and observe whether the working light of the equipment is on normally. • Check whether the Wi-Fi network is in good condition and restart the router. • If the device is located far away from the router, which results in the inability to obtain a good Wi- Fi signal, it is recommended to move the router for a closer place or add a Wi-Fi amplifier to improve the Wi-Fi performance of the home. Delete the camera from your ANRAN account and add it again after resetting the device. • Check whether the device firmware and application program are the latest version.

2. Update router or Wi-Fi password?

Delete the camera from your ANRAN account. After resetting the device, use the new Wi-Fi and password to add it again.

3. Can't play historical video?

4. Why doesn't the device identify the SD card ?

• Please insert the Micro SD card before power on; • It is recommended to use San Disk, Samsung and other brand cards: • It is recommended to use a standard class 10 TF card; • Only FAT32 format is supported. • TF card can't be identified when the internet environment is not good.

5. Why the battery life of my device is poor?

• Please check whether the number of alarms is foo frequent. Because the working time of the device determines the battery life. The more frequent PIR wake-ups, the faster the battery consume due to the longer working time. It is recommended to appropriately lower the motion detection sensitivity of the device and set the alarm interval and alarm time plan. (Note: Outdoor air conditioning units, moving cars and the passing pedestrians will cause frequent alarms. Please adjust the angle of the device to avoid these objects.) • In cold weofljsr, je battery capacity will be reduced, which will affect the endurance of the device.

6. The phone cannot receive the alarm push?

7. How to judge whether the charging is successful?

The device's charging indicator light is red, which means it is charging. A blue light means that charging is complete. It will take approximately 10 hours or more to fully charge.

8. What should I do if the charge fails?

• Determine whether the power adapter is good, try another one. • Determine whether the Type-C charging cable is good, try another one. • The charging indicator may be defective, please check the charging condition in the phone APP. • Determine whether the charging port of the device is not in good contact with the Type-C charging cable. • The device has a low temperature charging protection module, please don't charge the device at low temperatures.

Warranty Tips

Please fill in the following information or scan QR code to activate the free 12-month warranty from the order date on.
After finish filling or scanning, please take a picture and send it to the email(support@anran-cctv.com). Then your free warranty will take effect!
During the warranty period, if any parts of product are damaged, please contact immediately and we will provide satisfactory resolution.
Order Date:………………………………………………….
Order Number/ID:………………………………………..
Buyer E-mail:……………………………………………….
Buyer Tel:………………………………………………….
Contact us
  www.anran-cctv.com
support@anran-cctv.com
  1-866-958-6988 (US)
44-208610 1559 (UK)

Free Warranty

Documents / Resources

| ANRAN F1 Pro 2K 3G/4G LTE Solar Battery Security Camera [pdf] User Guide
F1 Pro 2K 3G 4G LTE Solar Battery Security Camera, F1 Pro, 2K 3G 4G LTE Solar Battery Security Camera, 3G 4G LTE Solar Battery Security Camera, LTE Solar Battery Security Camera, Solar Battery Security Camera, Battery Security Camera, Security Camera, Camera
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>