ANRAN P3 5MP Security Cameras Wireless Outdoor User Guide

: June 9, 2024
: ANRAN

Table of Contents

ANRAN P3 5MP Security Cameras Wireless Outdoor
What’s Included
Product overview
CloudEdge App installation and Setup
Mounting the camera
Register an account
Set up WiFi for the camera
FAQ
FCC Statement
Warranty Tips
Contact us
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ANRAN P3 5MP Security Cameras Wireless Outdoor

ANRAN-P3-5MP-Security-Cameras-Wireless-Outdoor-PRODUCT

What’s Included

ANRAN-P3-5MP-Security-Cameras-Wireless-Outdoor-FIG-2

Product overview

ANRAN-P3-5MP-Security-Cameras-Wireless-Outdoor-FIG-3

CAUTION : Please insert the Micro SD Card according to the direction shown in the diagram. Micro SD Card might JAM if inserted incorrectly and device could be damaged.

SD Card Port : Support micro SD card for local storage (Max 128GB).
Reset button : Used to restore the camera to factory settings (Press and hold on 5-8s).
Card capacity requirements : 8-128GB.
Read and write speed requirements : class10 level.
File format : FAT32.

CloudEdge App installation and Setup

Search “ANRAN” on apple store or google play to download the app.

from Google Play
from Apple Store

Download on the App Store

Get it on Google Play

Mounting the camera

Select Height and location
Hang the camera 7-10ft (78-118 inch) above the ground. This height maximizes the detection range of the motion sensor of the camera. Avoid placing the camera under direct sunlight.

Installation

Drilling according to position sticker, drill bit: 15/64″(6 mm)
Insert the plugs
Tighten the screw.

What is required:

ANRAN-P3-5MP-Security-Cameras-Wireless-Outdoor-FIG-7

Test the Wifi signal at installation position
Use cell phone to test Wifi signal quality at the installation position before installing camera, make sure the Wifi router can provide good Wifi signal.

Register an account

The ANRAN app that is necessary to operate the camera. Signing up for storage in the cloud is totally optional and is really not necessary when using an onboard Micro SD card.

Open the APP to sign up an account. Go to the login interface, and click “Sign Up”.
Sign up with your email address, and click “Next”.
Set up an “Nickname” and “Password” for your APP, click “Done” to complete.

Set up WiFi for the camera

Bring both your mobile phone and your camera close to your router (max distance of 5 meters/16 feet).
Note : The camera can only connect to a 2.4 GHz Wifi signal. It does not support using a 5 GHz signal. Therefore, please ensure you connect to a 2.4 GHz signal on your network as shown in the below illustration.
Log in to “ANRAN”, then tap the “” icon in the center. Tap “Camera” to add device
Reset the device and wait for a flashing RED indicator light, then tap “Next”.
Selecting the Wi-Fi the device needs to connected with (your home Wi-FI), input the password and click “Next”.
Use the camera to scan the QR code on your mobile phone as noted below. When the scan is complete you will hear a prompt tone then push Next.
When connecting, as stated earlier, you should make sure that the router, mobile phone and the camera and are as close together as possible (max 5 meters/16 feet). When a successful connection occurs a “click” will be heard anda checkmark will be noted as shown below. The camera will show witha numerical name that can be changed to your likings such as Driveway Camera, Street View Camera or whatever.

FAQ

Q: The device cannot be previewed properly?
A: Check whether the network is normal, you can place the camera close to the router, and if not, it is recommended to reset the device and add it again.
Q: Why is it still in the list of devices after reseting?
A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App.
Q: How to “connect” the camera to another router ?
A: First remove and reset the device on the App and then configure the device again by the App.
Q: Why doesn’t the device identify the Micro SD card?
A: It is recommended that the Micro SD card be inserted when the power to the camera is off and that it is fully inserted correctly. Make sure the Micro SD card has been formatted with FAT 32. If not, this can be done via the app.
Q: Why can’t I receive notifications via the mobile phone’s app?
A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm.

Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Warranty Tips

Please fill in the following information or scan QR code to activate the free 12-month warranty from the order date on. After finish filling or scanning, please take a picture and send it to the email(support@anran- cctv.com). Then your free warranty will take effect! During the warranty period, if any parts of product are damaged, please contact us immediately and we will provide satisfactory resolution.