MiBOXER E3-RF 3 In 1 RGBWW Wireless LED Controller Instruction Manual

MiBOXER E3-RF 3 In 1 RGBWW Wireless LED Controller Instruction Manual

Product features

Made by new 2.4GHz wireless trashing technology with low power consumption, strong ability to build network atomically and an-interference. with MI Boxer 2.4GHz gateway to get wireless dimming color, remote control, Ming control, group control, music rhythm fanon. Support 2.4G RF remote control.

Set up output mode

Set up correct output mode based on the feature of lights Seng method: Press “SET” button canorously to switch output mode (anon: it will log out without operon within 3 seconds)

Output mode sheet ( confirm output mode based on color of indicator)

Compatible with these 2.4G RF remote controls (Purchased separately)

2.4G RF Remote control instruction

1). Linking Code Instructions

⚠ Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)

2). Unlinking Code Instructions

⚠ Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)

3). Auto transmitting & Synchronization (only for remote control)

Remote signal auto transman One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.
Dynamic modes auto synchronizing Mul lights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m)

4). Dynamic mode table silicon (only for remote control)

Select dynamic mode table 1: While the light is in stack mode, short press ” S+ ” boon 5 mess quickly unl blue light flashes 3 mes slowly, stac mode is caveated successfully. Select dynamic mode table 2: While the light is in stac mode, short press ” S- ” button 5 mes quickly unl yellow light flashes 3 mes slowly, stac mode is caveated successfully.

Dynamic mode table 1 (default)

Dynamic mode table 2 (need to switch manually)

5). PWM high frequency / low frequency switching (only for remote

control)

Switch to high frequency (16KHz): Press “OFF” button 1 me within three seconds and press “ON” button 5 times, Activated successfully once led light flashes 2 times quickly.

Switch to low frequency (250Hz): Press “ON” button 1 me within three seconds and press “OFF” button 5 times, Activated successfully once led light flashes 2 times slowly.

6). “Do Not Disturb” mode is activated and shut down (default activated)

Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy) 2.4G RF Remote turn on and turn off instruction
Turn on “Do Not Disturb” mode: Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light flashes four times quickly. Attention: Do not disturb mode is activated

1. When the light is OFF status (For example: Use app or remote to turn off light)
   The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice times to activate light or use APP / remote to cavate light)

2. When the light is ON status The light is ON status once you turn off and turn on power one me.

Turn off “Do Not Disturb” mode: Press “ON” button three times within three seconds and press “OFF” button three times, closed successfully once led light flashes four times slowly.
Attention: The light will be always “ON” status if you turn on and turn off power once user closed “Do Not Disturb” mode.

DMX512 LED Transmitter Control (Purchased separately)

Only for RGB+CCT output mode

DMX512 LED Transmitter Link/Unlink

(1) Follow instruction of DMX512 transmitter (FUTD01), Choose the zone for the light by pressing ” + ” or ” – ” (e.g. “CH12” means zone 12)

Link
The controller is powered off for 10 seconds and then powered on, or press ” SET ” button 1 me.

Short press ” SET ” 3 times within 3 seconds while the indicator of controller is ON

Link is done once indicator of controller flashes 3 times slowly

Unlink
The controller is powered off for 10 seconds and then powered on, or press ” SET ” button 1 me.

Short press ” SET ” 5 times within 3 seconds while the indicator of controller is ON

Unlink is done once indicator of controller flashes 10 times quickly

⚠ If the link or unlink failed, please follow the above steps again.

Attention

1. Please turn off power supply before installation.
2. Please ensure input voltage to be same as requirements from device.
3. Don’t disassemble device if you are not expert, otherwise it will damage it.
4. Please do not use the light in the place with widely range metal area or strong electromagnet wave nearby, otherwise, the remote distance will be seriously affected.

https://miboxer.com/light/video/1pc_remote.html

Scan QR code to watch 2.4GHz series video instrucon Or enter into following link directly https://miboxer.com/light/video/1pc_remote.html

Made in China

References

• Remote Series Video - MiBoxer
• Remote Series Video - MiBoxer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>