ROADWORX BS-2400 Monitor Speaker Stand User Manual

BS-2400 Monitor Speaker Stand
User Manual

BS-2400 Monitor Speaker Stand

BS-2400 Stand

General information

This document contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the document for future reference. Make sure that it is available to all those  using the product. If you sell the product to another user, be sure that they also receive this document.
Our products and documentation are subject to a process of continuous development. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de.
1.1 Symbols and signal words
In this section you will find an overview of the meaning of symbols and signal words that are used in this document.

dangerous situation that will result in death or serious injury if it is not avoided.
CAUTION!| This combination of symbol and signal word indicates a possible dangerous situation that can result in minor injury if it is not avoided.
NOTICE!| This combination of symbol and signal word indicates a possible dangerous situation that can result in material and environmental damage if it is not avoided.
Warning signs| Type of danger
| Warning – danger zone.

Safety instructions

Intended use

This speaker stand is used for stable fixing and height-adjustable installation of loudspeaker cabinets. Use the product only as described in this user manual. Any other use or use under other operating conditions is considered to be  improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This product may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this product only if they are supervised or instructed by a  person who is responsible for their safety.

Safety

DANGER!
Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can injure themselves when handling the product. Never allow children to play with the packaging material and the product. Always store packaging material out of the reach of babies and small children. Always dispose of packaging material properly when it is not in use. Never allow children to use the product without supervision. Keep small parts away from children and make sure that the product  does not shed any small parts that children could play with.
CAUTION!
Risk of injury due to tipping of the stand during loaded transport!
If the stand is moved without having removed the installed devices, the stand may tip over and cause injuries and property damage.
Remove the installed devices before transporting the stand.
CAUTION!
Risk of injury due to tipping of stand on an unsuitable ground!
When the stand is installed on soft or uneven ground, the stand may tip over and cause injuries and property damage. Install the stand only on even and solid ground.
CAUTION!
Risk of injury due to tipping of the stand from excessive loading!
In case of excessive loading, the stand might tip over, causing injury and property damage. Never exceed the specified maximum load for the stand.

Features

Special features of the speaker stand:

• Extendible up to a height of 2.15 m
• Centric load capacity up to 50 kg
• Extension tube made of hardened steel
• Legs and cross braces made of aluminum
• M10 female thread at the 35 mm flange
• Transport length when folded: 1.18 m

Operating

Unpack and check carefully there is no transportation damage before using the product. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
CAUTION!
Risk of injury due to tipping of the stand during loaded transport!
If the stand is moved without having removed the installed devices, the stand may tip over and cause injuries and property damage.
Remove the installed devices before transporting the stand.
CAUTION!
Risk of injury due to tipping of stand on an unsuitable ground!
When the stand is installed on soft or uneven ground, the stand may tip over and cause injuries and property damage.
Install the stand only on even and solid ground.
CAUTION!
Risk of injury due to tipping of the stand from excessive loading!
In case of excessive loading, the stand might tip over, causing injury and property damage.
Never exceed the specified maximum load for the stand.
NOTICE!
Possible staining due to plasticizer in rubber feet!
The plasticizer contained in the rubber feet of this product may react with the coating of the floor and cause permanent dark stains after some time.
If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and the floor.
Comply with regulations
When installing and operating, make sure to follow the standards and regulations that apply in your country.

Setting up

1. Unfold the feet of the stand until the cross-braces are in a horizontal position.
2. Fix this position with the safety screw on the slider to which the three feet are attached.
3. Lift the speaker box onto the extension tube. The weight of the speaker box to be installed must not exceed the maximum centric load of 50 kg.
4. Fold out the hand crank.
5. To adjust the height, untighten the locking screw at the crank case.
6. Press and hold the yellow security button at the crank case while adjusting the desired height with the hand crank.
7. Release the yellow security button at the crank case, fix the position of the extension tube with the locking screw at the crank case and fold the hand crank back in.

Dismounting

1. Fold out the hand crank.
2. Untighten the locking screw at the crank case.
3. Press and hold the yellow security button at the crank case while fully lowering the extension tube.
4. Release the yellow security button at the crank case, fix the position of the extension tube with the locking screw at the crank case and fold the hand crank back in.
5. Lift off the speaker box from the extension tube.
6. Loosen the safety screw on the slider to which the three feet are attached.
7. Fold up the feet of the stand.

Technical specifications

Tube diameter

| Main tube| 0 41 mm
Extension tube| 0 35 mm
Feet| 0 35 mm
Holder type| M10 female thread at the flange / 35 mm flange
Load capacity, max. (not extended, with centric load)| 50 kg
Transport dimensions (W x H x D)| 170 mmx 1180 mmx 130 mm
Weight| 7.5 kg
Colour| Black

Further information

EU Declaration of Conformity

Name and address of
manufacturer / EU-AR| Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
---|---
THIS DECLARATION OF CONFORMITY IS ISSUED UNDER THE SOLE RESPONSIBILITY OF:
Name and address of manufacturer| Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Product identification| 568328 Roadworks BS-2400 Speaker Stand
THE PRODUCTS MENTIONED IN THIS DECLARATION ARE IN CONFORMITY WITH:
EU Community Legislation| Machinery Directive 2006/42/EC
Harmonised standards| Safety of machinery
ANNEX I OF 2006/42/EC
SIGNED FOR AND ON BEHALF OF:
Place and date of issue| Burgebrach, 26 May 2023

Protecting the environment

Disposal of the packaging material

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de
15.09.2023, ID: 568328 (V4)

References

• Buy musical instruments online from the market leader – Thomann United States

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>