ROADWORX TM-X Tablet Holder Instruction Manual
- June 12, 2024
- ROADWORX
Table of Contents
ROADWORX TM-X Tablet Holder Instruction Manual
TM-X
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de
1. Safety instructions
Intended use
This product is intended for stable fixing and adjustable installation of
monitors, tablets, speakers or similar. Use the product only as described in
this user manual. Any other use or use under other operating conditions is
considered to be improper and may result in personal injury or property
damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are properly disposed of and are not
in the reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like)
from the product. They could swallow the pieces and choke! Never let children
play unattended with the product.
**** CAUTION!
Danger of tipping when transported under load
If the stand is moved without having removed the installed device, the stand
may tip over and cause injuries and property damage. Remove the installed
device before transporting the stand.
**** CAUTION!
Danger of tipping due to overload
In case of overload, the stand may tip over and cause injuries and property
damage. Never exceed the maximum load capacity specified for the stand.
2. Overview
For the TM-X stand system the following items are available:
3. Installation
- Place all components on a suitable mounting surface for mounting. Use a soft padding to prevent damages to the surfaces.
- The illustrations are for illustrative purposes and may differ from the actual product.
TM-X Pole Clamp (item no. 540259, 540264, 540262)
Loosen the locking screw of the clamp and place the clamp on the desk edge.
Tighten the locking screw of the clamp.
For adjusting the desktop stand height, loosen the Allen screws using an Allen key. Adjust the desired height and tighten the Allen screws using an Allen key.
TM-X Pole Fixed (item no. 540261, 540265, 540263)
Loosen the locking screw and place the stand in the recess of the desktop.
Tighten the locking screw.
TM-X Arm (item no. 540250, 540252, 540254), TM-X Stand Mount (item no.
540271)
Open the cover of the desktop stand TM-X Pole Clamp (item no. 540259, 540264,
540262) or TM-X Pole Fixed (item no. 540261, 540265, 540263).
Slide the arm or the holder from the top in the recess of the desktop stand.
Adjust the desired arm height and tighten the Allen screws using an Allen key.
Replace the cover on the desktop stand. Pay attention to the correct location
of the positioning pins of the cover.
TM-X Tablet Holder (item no. 540268)
Loosen the locking screw and place the tablet holder in the recess of the TM-X
Arm (item no. 540250, 540252, 540254). Tighten the locking screw.
Loosen the locking screw of the mounting hole and adjust the tilt of the
tablet holder up to 90°. Tighten the locking screw.
Loosen the locking screws of the supporting arms, pull out the supporting arms
completely and place the tablet in the corner supports of the lower supporting
arms.
Adjust the corner supports to the thickness of the tablet. Make sure that the
tablet sits firmly in the corner supports. Tighten the locking screws of the
corner supports.
Reinsert the supporting arms and fix the tablet. Tighten the locking screws of
the supporting arms.
TM-X VESA Mount (item no. 540267)
Loosen the locking screw and place the monitor holder in the recess of the
TM-X Arm (item no. 540250, 540252, 540254). Tighten the locking screw.
For adjusting the monitor holder tilt, loosen the Allen screws using an Allen
key. Adjust the desired tilt and tighten the Allen screws using an Allen key.
Mount the monitor with four screws and washers to the monitor holder.
TM-X Laptop Holder (item no. 540269)
Loosen the locking screw and place the laptop holder in the recess of the TM-X
Arm (item no. 540250, 540252, 540254). Tighten the locking screw.
For adjusting the laptop holder tilt, loosen the Allen screws using an Allen
key. Adjust the desired tilt and tighten the Allen screws using an Allen key.
For adjusting the clamping range of the laptop holder, pull out the lateral
clamping jaws at the sides of the the laptop holder. Make sure that the laptop
sits firmly between the clamping jaws.
TM-X Studio Monitor Holder (item no. 540270)
Loosen the locking screw of the speaker holder and slide him on the arm.
Tighten the locking screw.
Slide the arm with the speaker holder from above in the recess of the desktop
stand TM-X Pole Clamp (item no. 540259, 540264, 540262) or TM-X Pole Fixed
(item no. 540261, 540265, 540263). Adjust the desired height of the arm and
tighten the Allen screws using an Allen key.
For adjusting the speaker holder tilt, loosen the Allen screws using an Allen key. Adjust the desired tilt and tighten the Allen screws using an Allen key.
TM-X VESA Mount for Bar (item no. 542189, 542190)
Remove the rubber plugs and slide the arm in the holder. Place the rubber
plugs in the recesses of the arm.
Loosen the locking screw of the monitor holder and place the monitor holder in
the recess of the arm. Tighten the locking screw.
For adjusting the monitor holder tilt, loosen the Allen screws using an Allen
key. Adjust the desired tilt and tighten the Allen screws using an Allen key.
Mount the monitor with four screws and washers to the monitor holder.
TM-X Bar (item no. 542186, 542188)
Loosen the Allen screw using an Allen key. Remove the Allen screw, the washer
and the hex nut, and remove the bar from the holder. Place the holder in the
recess of the desktop stand TM-X Pole Clamp (item no. 540259, 540264, 540262)
or TM-X Pole Fixed (item no. 540261, 540265, 540263)
Slide the TM-X VESA Mount for Bar (item no. 542189, 542190) on the bar and
tighten the locking screw.
Place the ready-equipped bar in the holder, insert the Allen screw, the washer
and the hex nut, and tighten the Allen screws of the bar using an Allen key.
4. Technical specifications
Roadworx TM-X Pole Clamp
Roadworx TM-X Pole Fixed
Roadworx TM-X Arm
Roadworx TM-X Stand Mount
Roadworx TM-X Tablet Holder
Roadworx TM-X VESA Mount
Roadworx TM-X Laptop Holder
Roadworx TM-X Studio Monitor Holder
Roadworx TM-X Bar
Roadworx TM-X VESA Mount for Bar
Roadworx TM-X Thread Option
5. Protecting the environment
Disposal of the packaging material
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>