GOAL ZERO 1250 Hpp Solar Wall Plate Kit Installation Guide

GOAL ZERO 1250 Hpp Solar Wall Plate Kit

Product Usage Instructions

• 2x HPP+ Solar Wall Plugs
• 1x Interior Outlet Cover
• 2x Mounting screws for the interior outlet cover
• 2x RJ45 couplers

Additional Items Needed for Installation (Not Included):

1. Outdoor Outlet Cover
2. 2x Gang Outlet Box
3. Internal Wall Cable for solar (10 AWG, 90C rated)
4. CAT5e or CAT6 cable
5. RJ45 male connectors
6. Wing-Nut Wire Connectors
7. Goal Zero Solar Solution (e.g., Nomad 400)
8. Goal Zero Male to Male 12 HPP + Extension Cable, SKU 98710
9. Goal Zero Yeti PRO 4000
10. Goal Zero Tank PRO 4000 expansion tank(s) (optional)
11. Goal Zero Haven 10 manual transfer switch (optional)

FAQ

• Q: Where can I find the latest product information and user guide updates?
• A: For the most recent information, visit www.goalzero.com or contact Goal Zero support at the provided numbers.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Please read all warnings, instructions and cautions carefully before use to avoid personal injury, property damage or damage to your Yeti PRO 4000, or any connected products. Goal Zero reserves the right to update this document without prior notice. Please visit www.goalzero.com to find the latest product information and the most recent version of the User Guide.

INSTRUCTIONS ON RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

• WARNING – High Voltage. The system may include voltages up to 150 V.
• WARNING – This connector should only be used with Goal Zero Products.
• WARNING – This product must be installed by a qualified and licensed electrician.

Specifications

• Connector: Female Locking HPP+
• Power Wires: 10 AWG
• Data Wires: 18 AWG
• Current Rating: 40 A
• Plate Dims: 3.92 x 1.97 x 0.05in (9.96 x 5.00 x 0.15cm)
• Warranty: 2 years
• Certifications: RoHS, REACH, Prop 65, UL1977

Getting Started

In the Box

1. 2x HPP+ Solar Wall Plugs
2. 1x Interior Outlet Cover
3. 2x Mounting screws for the interior outlet cover
4. 2x RJ45 couplers

Additional Items Needed for Installation (Not Included)

1. Outdoor Outlet Cover

2. 2x Gang Outlet Box

3. Internal Wall Cable for solar (10 AWG, 90C rated)
   *Note: We recommend using different colored cables for positive and negative.

4. CAT5e or CAT6 cable

5. RJ45 male connectors

6. Wing-Nut Wire Connectors

7. Goal Zero Solar Solution (eg. Nomad 400)

8. Goal ZeroMale to Male 12′ HPP + Extension Cable, SKU 98710

9. Goal Zero Yeti PRO 4000

10. Goal Zero Tank PRO 4000 expansion tank(s) (optional)

11. Goal Zero Haven 10 manual transfer switch (optional)

Install Overview

Installation Instructions

How to Install the Wall Plate

1. Choose a location to install your wall plate indoors. It should be within 12 feet of where you’ll be storing your
   Yeti power station. For assistance choosing the best location, consult your electrician.

2. Electrical box preparation

   • If using an existing box: Follow the industry standards for running wires.
   • If using a new box: Choose a location for your outdoor wall plate. Be sure it is within reach of your desired solar location. Install the box according to industry standards.

3. Run the solar cables through the wall between the exterior and interior outlets. Then run the Cat5e/Cat6 cable. If installing via a conduit, please ensure the solar wiring is in a different conduit run from the Cat5e/Cat6, per NEC requirements. If running cables internally, make sure there is at least 6 inches of space between the high-voltage solar cable and the low-voltage Cat5e/Cat6 cable.

4. Install exterior and interior electrical boxes according to required NEC standards. Make sure the Cat5e/Cat6 and 10 AWG wiring enter and exit the box from different entry points to provide high voltage/low voltage isolation.

5. Use a Wing-Nut Wire Connector to connect the positive solar cables.

   • Use a Wing-Nut Wire Connector to connect the negative solar cables
   • Use the Coupler to connect the internal wall Cat5e/Cat6 cable to the interior wall plate Cat5e/Cat6 using the coupler. Repeat for the exterior wall plate.
   • Screw the wall plug into the wall plate.

6. Repeat step 4 for the outdoor box.

7. Attach the outdoor plate for the outdoor plug. Attach the indoor plate to the indoor plug.

8. Plug the Male-to-Male HPP+ Connector into the indoor plug and Yeti power station.

9. Plug all solar extension cables from the outdoor plug to the solar location before connecting the solar

10. Connect solar. For your safety, the solar panels should always be the last thing connected to reduce the risk of exposure to live voltages.

CONTACT

• GOAL ZERO HEADQUARTERS
• Draper, UT 84020
• 1-888-794-6250
• Designed in the U.S.A.
• Made in China
• Goal Zero Yeti is a trademark of Goal Zero.
• GOALZERO.COM.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>