UNITEK S1222A USB-C to PCIe NVMe M.2 SSD Enclosure and SATA III Adapter User Manual
- June 15, 2024
- UNITEK
Table of Contents
USB-C to PCIe/NVMe M.2 SSD Enclosure and SATA III Adapter With Offline
Clone
User Manual
Thank you for choosing Unitek USB-C to PCIe/NVMe M.2 SSD and SATA III Enclosure Please read the user manual carefully before use and save them. If you need any help, please contact our professional customer service team at: support_us@unitek-products.com
Product Diagram
- USB-C 10Gbps
- DC 12V2A
- OFF/ON
- Offline Clone
- Switch
Specification
LED Indicator:
Green:
- Light on when the power is connected.
Yellow:
- Light on to indicate the connection of the Disk accordingly;
- Light flashes during read/ write;
Blue:
- Light on when the Clone is processing. Four lights refer to: 25%, 50%, 75%, 100%. When all of them are lighted on, the Clone is completed;
- When the Clone is started but Disk B (Target) Capacity is smaller than Disk A (Source), the Clone cannot be processed. In this case, the yellow indicators will be reciprocally flashing in two groups: 25% & 50% and 75% & 100%.
How to Use
- Aluminum Heat Exchanger
- Silicone Thermal Pad
- SSD
I. How to install the M.2 SSD:
- Remove the surface layer of both Aluminium Heat Exchanger and Silicone Thermal Pad.
- Stick the Silicone Thermal Pad in between the M.2 SSD and the Aluminium Heat Exchanger.
- Slide to open the enclosure.
- Insert the M.2 SSD diagonally down into the PCIe/ NVMe slot and lock up with the pluggable rubber mount.
- Close up the cover.
Notice: For your safety, please disconnect from the power before remove the M.2 SSD from the enclosure.
II. How to install the Hard Drive(HDD) or Solid-State Drive (SSD):
- Put off the cover.
- Insert the HDD or SSD to the SARA interface.
III. How to clone:
- Press the Clone Button (shown as B above) and hold for 3 seconds until the four blue lights are on, then free the button and press it again. Afterward, the Clone from Disk A to Disk B will start to process. Please make sure the storage capacity of Disk B (Target) is equal or larger than Disk A (Source).
- Four blue lights will on according to the progress from 25%, 50%, 75% to 100%. When all of them are lighted on, the Clone is completed.
- Switch off the docking station and unplug the power, then you can safely process the ejection of the disk A or B.
Notice: Your disk might have bad sectors if the blue indicator keeps flashing. In that case, the bad sectors will be ignored in order to help you complete the clone unless the bad sectors lead the malfunction of your disk and the clone cannot be processed. We suggest you seek experts’ advice for the repair of your disk.
Package Contents
- M.2 and SATA Enclosure
- Rubber Mount
- Aluminum Heat Exchanger
- Silicone Thermal Pad x2
- User Manual
- USB-C 10Gbps Cable with USB-A Adapter
- 12V/2A Power Adapter
Safety Notes
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
- Do not open the device or continue to operate it if it becomes damaged.
- Do not modify the product in any way. Doing so avoids the warranty.
- Do not drop the product and do not expose it to any major shocks.
- Keep this product, like all electrical products, out of the reach of children!
Note:
-
With the M Key interface which belongs to the PCIe/NVMe protocol channel.
When installing the SSD for this product, kindly be reminded to check the compatibility. -
The hard drive may not be moved after connecting the power supply unit to the socket. This could result in damage to the hard drive and data loss.
-
The hard drive adapter may not be unplugged from the PC during data transfer under any circumstance. Data may be lost.
Warranty
The Unitek USB-C to PCIe/NVMe M.2 SSD and SATA III Enclosure is covered by Unitek warranty for 24 months. If the product fails due to manufacturer defects, please contact us by email at: support_us@unitek- products.com
Documents / Resources
|
UNITEK S1222A USB-C to PCIe NVMe M.2 SSD Enclosure and SATA III
Adapter
[pdf] User Manual
S1222A USB-C to PCIe NVMe M.2 SSD Enclosure and SATA III Adapter, S1222A,
USB-C to PCIe NVMe M.2 SSD Enclosure and SATA III Adapter, Enclosure and SATA
III Adapter, SATA III Adapter
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>