UNITEK D1026B uHUB N9 Plus Multiport Adapter User Manual
- June 11, 2024
- UNITEK
Table of Contents
- UNITEK D1026B uHUB N9 Plus Multiport Adapter
- Product Information: 9-in-1 USB Hub
- Technical Data
- Safety Notes
- System Requirements
- Service and Support:
- Product Usage Instructions:
- Product Overview
- Package Contents
- Safety Notes
- Warranty Disclaimer
- Technical Data
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
UNITEK D1026B uHUB N9 Plus Multiport Adapter
Product Information: 9-in-1 USB Hub
The uHUB N9+ is a dual display hub that comes with HDMI, VGA, 3-Port USB-A,
Gigabit Ethernet, 100W PD and Dual Card Reader D1026B. It is compatible with
systems such as Windows XP or later versions, Mac OS X or later versions,
Android 7.0 or later versions, and Linux. The USB hub has a USB-C full-
featured
connector and USB 5Gbps specification. It also has safety notes and warranty
disclaimer.
Technical Data
- VGA (1080P) HDMI (4K@30Hz) USB-C Full-Featured Connector
- USB-C for PD 100W charging
- Gigabit Ethernet RJ45 (1000Mbps)
- USB-A Data (5Gbps) Card Reader (12mm or 24mm)
Safety Notes
UNITEK assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
System Requirements
- Windows XP or later versions
- Mac OS X or later versions
- Android 7.0 or later versions
- Linux
Service and Support:
Further support information can be found on the website www.unitek- products.com or by email at support@unitek-products.com.
Product Usage Instructions:
To use the UHUB N9+ USB hub, follow the steps below:
- Connect the USB-C connector of the hub to the USB-C port of your PC, laptop, or tablet.
- Connect the HDMI or VGA connector to your display device.
- Connect the Ethernet cable to the RJ45 port of the hub and to your network device.
- Connect USB devices to the USB-A ports of the hub.
- Insert a memory card into the card reader slot of the hub.
- The hub supports PD 100W charging, so you can connect the USB-C power adapter to the hub to charge your device.
Note: Make sure that your system meets the system requirements mentioned above before using the UHUB N9+ USB hub. Also, refer to the safety notes and warranty disclaimer mentioned in the user manual to avoid any damage to your device.
9-in-1 USB Hub UHUB N9+
Dual Display Hub with HDMI, VGA, 3-Port USB-A, Gigabit Ethernet, 100W PD and
Dual Card Reader D1026B
Product Overview
Package Contents
- uHUB N9+
- User Manual
Safety Notes
-
Do not attempt to service or repair the product yourself. Leave any and all
service work to qualified experts. -
Do not open the device or continue to operate it if it becomes damaged.
-
Do not modify the product in any way. Doing so voids the warranty.
-
Keep this product, like all electrical products, out of the reach of children.
Warranty Disclaimer
UNITEK assumes no liability and provides no warranty for damage resulting from
improper installation/mounting, improper use of the product or from
failure to observe the operating instructions and/or safety notes.
Technical Data
- Compatibility USB-C port
- USB Specification USB 5Gbps
- Windows XP or later ver.
- Mac OS X or later ver.
- Android 7.0 or later ver. Linux System requirements
- (PC, Laptop & Tablet)
Note
- To use the charging function for the upstream device, it must support USB Power Delivery (PD) or Thunderbolt 3 technology.
- To use the HDMI or VGA function, the device must support Dsiplay Port Alternate Mode or Thunderbolt3 technology.
Service and Support
Further support information can be found here: www.unitek-
products.com
Email: support@unitek-products.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>