tp-link POE10E PoE Extender Fast Ethernet Installation Guide
- June 1, 2024
- tp-link
Table of Contents
tp-link POE10E PoE Extender Fast Ethernet
Product Information
General Specifications
- Standards: IEEE 802.3i, IEEE802.3u
- LED: PWR
- Cable Type: UTP/STP of Cat. 5E or above (based on the standards that the connected devices comply with)
Frequently Asked Questions
- Q1. Which devices can work normally with the extender?
- A: Only PSE and PD devices compliant with IEEE 802.3 af/at can function well with the extender. Do not use the extender with other devices to extend the data transmission distance only.
- Q2. Why is the Power LED not lit?
- A1: Ensure your network cable is in good condition.
- A2: Ensure both PSE and PD devices are connected to the correct ports.
- Q3. When should I enable the 10Mbps mode?
- A: If you want to extend the transmission distance between the extender and…
Connection
Note:
- Make sure the Power Sourcing Equipment (PSE) and PD devices are connected to the corresponding ports properly.
- The extender supports both Auto-Negotiation mode and 10Mbps mode. In 10Mbps mode, the maximum speed will downgrade to 10 Mbps.
- The total cable length (a+b) is not recommended to exceed 350m, and the actual transmission distance may vary due to the type and quality of cables, power consumption of PD devices, voltage at PSE, etc. If a or b ＞ 100m, enable 10Mbps mode first.
- If 100m ＜ a ≤ 250m, make sure the PSE supports extend mode.
Power LED Explanation
Specifications
General Specifications
- Standards: IEEE 802.3i, IEEE802.3u
- LED: PWR
- Cable Type: UTP/STP of Cat. 5E or above (based on the standards that the connected devices comply with)
- Ports: 1*10/100 Mbps Auto-Negotiation RJ45 PoE IN Port
- 1*10/100 Mbps Auto-Negotiation RJ45 PoE OUT Port
- PoE Input: Compliance with 802.3af/at devices
- Maximum PoE Output: 20W
Environmental and Physical Specifications
- Operating Temperature: 0˚C to 45˚C (32˚F to 113˚F)
- Storage Temperature: -40˚C to 70˚C (-40˚F to 158˚F)
- Operating Humidity: 10% to 90%RH non-condensing
- Storage Humidity: 5% to 90%RH non-condensing
FAQ
- Q1. Which devices can work normally with the extender?
- A: Only PSE and PD devices compliant with IEEE 802.3 af/at can function well with the extender. Do not use the extender with other devices to extend the data transmission distance only.
- Q2. Why is the Power LED not lit?
- A1: Ensure your network cable is in good condition.
- A2: Ensure both PSE and PD devices are connected to the correct ports.
- Q3. When should I enable the 10Mbps mode?
- A: If you want to extend the transmission distance between the extender and the PD device to more than 100m, enable the 10Mbps mode first.
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- This product can be powered only by power supplies that comply with Power Source Class 2 (PS2) or Limited Power Source(LPS).
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
Declaration of Conformity
EU Declaration of Conformity
- TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
- The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
UK Declaration of Conformity
- TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility
- Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
- The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca
FCC STATEMENT
FCC compliance information statement
- Product Name: Fast Ethernet PoE+ Extender
- Model Number: POE10E
Responsible party:
- TP-Link USA Corporation
- Address: 10 Mauchly, Irvine, CA 92618
- Website: https://www.tp-link.com/us/
- Tel: +1 626 333 0234
- Fax: +1 909 527 6804
- E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Industry Canada Statement
- CAN ICES-3 (B)/NMB-3(B)
CE Mark Warning
- This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Explanation Of The Symbols
Explanation of the symbols on the product label
Symbols may vary from products. The label is at the bottom of the product.
Information
- To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.
- For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
© 2023 TP-Link
References
- Link: Simple, secure one-click payments
- TP-Link Community
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link
- WiFi Networking Equipment for Home & Business | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>