NEXXT SOLUTIONS NHE-S300 Smart Switch User Guide

June 4, 2024
Nexxt Solutions

NHE-S300 Smart Switch

SOLUTIONS NHE-S300 Smart Switch
User Guide

Notes Before Installation

  1. Wi-Fi Only supports a 2.4GHz network (802.11 b/g/n)

  2. The neutral wire is Required.

  3. basic electrical wiring knowledge or experience required, or please consult
    a professional electrician

  4. Never connect the neutral wire to any switch wires

  5. ON/OFF Button also can be used as a reset button, a long press to reset your smart switch to factory defaults. Only do this if you are sure you want to erase all your settings

Specifications

Type Smart Wi-Fi 3-Way Switch
Model NHES300
Power supply mode Neutral+Live Wire
Input AC1 10-125V-50/60Hz
Output 400W Max. for INC Bulb

150W Max. for CFL&LED Bulb
Wireless Frequency| 2.4GHZ
Wireless Standard| IEEE802.11 b/g/n

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 1

Indicator light meaning

Indicator Status Description
Green Flash Rapidly Ready for connection (Default Mode Only)
Green Flash Slowly (1 time every 3 S) Ready for connection (AP Mode Only)

Green light is
always on| Off| Turn the light off
Red light is
always on| On| Turn the light on
Green|  Flash Slowly| No Internet

Safety Notice:

  • Cut off the power before installation
  • Please use it only when it’s installed with RCD or current leakage protector at home
  • A neutral wire is needed to power the switch.

Installation Guide

STEP.1
Turn off the circuit breaker
Find your light’s control in your circuit breaker and turn it off, Then make sure the power is off by flipping your switch a few times.

STEP.2
Find the neutral wire
In the wall cassette. look for one or more white wires secured with a wire nut. Do you have a neutral wire?NEXXT SOLUTIONS NHE-S300 Smart Switch -
Figure 3

If you can’t find the neutral wire
Please change to another wall cassette. to find a neutral wire, if you really can’t find out a neutral wire in your wall cassette. please contact a professional electrician to help you.

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 4

Usually:
White represents the neutral wire
Black represents the hot wire
Green or yellow or a single bare copper wire representing the ground wire
The above is for reference only and cannot be used as a standard.
Install the 3-Way switch C in the cassette near the light

STEP.4
Turn on the circuit breaker
Turn on your switch’s power from the circuit breaker.
Press the switch a few times to make sure it works.

STEP.5
Check the Wi-Fi light
Tap NEXT when the Wi-Fi indicator light blinks

Install the “Smart Life” APP

Step A . Find out “Smart Life” app in the Apple app store, Google Play, or scan the QR code below and install it

The free app” Smart Life” is compatible with mobile devices that support IOS8.0 above, Android 4.4 above
Step B . Enter the register interface, and input the email address/phone number for getting the verification code to register an account. Please just log in if you already have a Smart Life account.

Step C: Add the switch to Smart Life APP
Note: This smart switch can only support a 2.4G network and cannot work with a 5.0G network. please check if your home network is 2.4G and make sure that your phone has  been connected to your WI-FI home network

  1. Tap the”+” button on the top right corner to add a device, the tap” Wall switch” to enter the next page.
    NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 7

Default Mode(Recommend)

Step 1. Make sure the indicator blinks rapidly, if not, hold the ON/OFF button for 7 seconds for reset.

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 10

Note: When finishing the default mode please go directly to Step. 9

AP Mode(Alternative)

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 9

Step 1. When the indicator blinks rapidly, press and hold the ON/OFF button for another 7 seconds. the indicator will blink slowly.

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 11NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure
12NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure
13NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure
14

Step D: Give a name to the switch and tap” Done”. you will find the device you’ve named is shown on the app homepage. Tap the device to enter the setting page.
Note: The name you give to the device will be the name for voice control on Amazon Alexa or Google Home later. For example, the device is named” Switch” in this user guide.NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure
15

After completing Part Two. you can now control the switch with Smart Life APP on this setting page.

Try the timer function to easily set up a schedule to turn on/off the smart switch.

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 17

If you want to connect to Amazon Alexa, Google Home, IFTTT control, please follow the instructions to find the guide in the app

NEXXT SOLUTIONS NHE-S300 Smart Switch - Figure 18

FAQ

Please note when adding a device:

  1. Confirm the device is powered on.
  2. Confirm the device is waiting for network configuration.
  3. Confirm that the device, smartphone, and router are as close to each other.
  4. Make sure the network function of the router and smartphone is unblocked.
  5. Confirm the entered router password is correct.
  6. Confirm adding device is under 2.4G Wi-Fi channel. Enable the broad case and not allow to hide Wi-Fi.
  7. Confirm that router’s encryption method is WPA2-PSK and the authentication type is AES, or both are set up as automatic.
  8. Confirm that the Wi-Fi name contains letters only.
  9. If the router’s connected device reaches the amount limit. Please try to turn off some device’s Wi-Fi function and configure it again.
  10. If the router enables the MAC address filter, please try removing the device form the MAC filter list and make sure the router is allowing the device to be connected.

Does control devise under 2G/3G/4G network?

The device and smartphone must be in the same Wi-Fi environment when adding the device. After successful addition, the device cam is controlled via the mobile network.

How to share my device with family?

Open App, enter into “shared device”, and tap “add sharing” to share the device with the family.

How to add a device?

Two methods to add a device:” Default Mode” and “AP Mode”.” Default Mode” is set up as default and can switch to “AP Mode”

Why can’t I control the load after installing the product?

  1. Please check if the wiring is correct.
  2. Please check if there is a neutral line in the cassette(a neutral line is required)
  3. Please check if the connected load exceeds the maximum value of the device

Which cartridge should the switch be installed in?

  1. Choose the electric box which is relatively far away from the fuse box. Live-out wire does not have voltage please use an electrical tester to verify it.
  2. If you are still not sure, simply choose either electric box to get started.

FCC NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference,
  2. this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Smart Home

Documents / Resources

| NEXXT SOLUTIONS NHE-S300 Smart Switch [pdf] User Guide
HAES300, X4YHAES300, NHE-S300 Smart Switch, NHE-S300, Smart Switch, Switch
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals