Optimant Lighting B09CV635TP Gold Pendant Lighting Instruction Manual

Optimant Lighting B09CV635TP Gold Pendant Lighting

Product Information

Specifications

• Parts Included: Single bar, Green ground screw, Canopy, Collar ring, Collar loop, Quick link, Chain, Loop, Tube, Fixture body, Socket
• Accessories Included : Wire connector, Mounting screw

Product Usage Instructions

Assembly & Installation:

1. Carefully remove all parts and accessories from the packaging.
2. Step A1: Measure and determine the correct number of links needed for proper hanging weight.
3. Step A2: Screw the tube onto the joint at the top of the fixture body.
4. Step A3: Attach the quick link to the chain and loop on the top of the tube.
5. Step A4: Weave fixture wires through the chain in and out of every other link.

Installation:

3. Turn off power: Shut off the electricity before starting any installation work.
4. Make installation:
5. Step B1: Attach the single bar to the outlet box with mounting screws.
6. Step B3: Pass the chain through the collar ring and then through the canopy.
7. Step B4: Pass the fixture wires through the collar loop to the top of the threaded nipple.
8. Step B6: Connect wires as shown in the provided wire connection chart. Ensure proper grounding.
9. Step B7: Secure the canopy to the ceiling by tightening the collar rings onto collar loop.
10. Step B8: Install a bulb with wattage within recommended limits.

(FAQ)

• Q : Can I install the product without a licensed electrician?
• A: While we recommend installation by a licensed electrician for safety reasons, following the provided instructions carefully can help you install the product correctly

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT：

TOOLS REQUIRED

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

• (C) Single bar (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Collar ring (1)
• (G) Collar loop (1)
• (H) Quick link (2)
• (I) Chain (1)
• (J) Loop (1)
• (K) Tube (1)
• (L) Fixture body (1)
• (M) Socket (1)

ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)
• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre-installation

• Step A1: By measuring, determine the correct numer o in s nee e or proper aging eig t. Using t e c ain p is,   disconnect and discard the unwanted part.
• Step A2 : Screw tube (K) onto the joint at the top of the fixture body (L).
• Step A3 : Attach a quick link (H) to the chain (I) and loop (J) on the top of the tube (K).
• Step A4 : Carefully weave fixture wires through the chain (I) in and out of every other link and stop just when you reach the top of the chain (I). Gently pull the wires to ensure the wires are not stressed.

Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

• A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
• B) Place the wall switch in the “OFF” position.

Make installation

• Step B1 : Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B). Note: be sure that the side of the single bar marked “GND” faces out.

• Step B2 : Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position.Unscrew collar ring (F) from collar loop (G) and remove canopy (E).
  Note: canopy (E) should be snug against the ceiling and collar loop (G) should be screwed with enough threads (no less than 6 threads) on the pre- assembled threaded nipple for more secure hanging. If not, adjust collar loop (G) on single bar assembly (C) by screwing collar loop (G) in or out of a single bar (C) until the secure length is achieved.

• Step B3: Pass chain (I) through collar ring (F) and then through canopy (E).

• Step B4: Open quick link (H), and attach quick link (H) to collar loop (G). Close quick link (H). Pass the fixture wires through the collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.

• Step B5 : If needed, shorten the length of the fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6″.

• Step B6 : Make wire connections Connect wires as below wires connection shown below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. Step B7: Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G). Step B8: Install the bulb (not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is already installed properly, and then you can turn on the light. Enjoy!

CLEANING.

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>