MODSTER MD10011 Desert Rookie Buggy User Manual

MODSTER MD10011 Desert Rookie Buggy

Introduction

Dear Customer,
Thank you for chosing a product from MODSTER Racing.
All models are functionally tested and carefully packed prior to delivery. Due to continuous development and improvement of our products, we reserve the right to make technical changes as well as changes in equipment and design without notice. Minor deviations of data and illustrations in this manual of the product you are presented with, can not be claimed. The responsible handling of the product is for your own safety and the safety of the uninvolved .Indispensably read the safety instructions in this manual carefully!

Warranty is subject to manufacturing and material defects and errors during normal use. We will not accept any liability for consequential damages:

• Damage caused by failure to observe the safety instructions or the operating instructions
• Force majeure, battles, incorrect handling
• Extraordinary use or foreign influence
• Unauthorized alterations or repairs carried out by unauthorized persons
• Damage caused by loss of control over the model
• Wear parts and normal wear
• Optical impairments
• Water damage if the „Water Resistant“ notices are ignored (see next pages)
• Damage caused by loss of control when batteries are not fully charged.
• Transport, shipping or insurance costs
• Costs for the proper disposal of the product as well as setup and restoration work done by the service.

Safety Notes

RC car models are no toys!

Always use the product responsibly.
As a distributor of the product, we have no direct influence on the correct handling and the correct operation of the product. The following safety instructions are designed to protect you and your environment from damage that may result from improper use. But also the product itself should be protected by this safety instructions. Please read this chapter carefully before using the product!

Use this product on surfaces or tracks specifically designated for model cars only.
Take care not to endanger anyone, take particular care with children!

Before Starting

We do not assume liability for non-observance of the safety instructions.
In such cases, the warranty / guarantee will be void.
We will not accept any liability for consequential damages!

The product is suitable for children under 14 years under the supervision of an adult.

Dispose of the packaging material, as this could become a hazard for children. Check with your insurance company whether the operation of a radio controlled model falls under the insurance cover.
If you do not have any experience in controlling RC models, first get familiar with the responses to the control commands on the standing model. If necessary, contact an experienced model pilot or RC club.
Before commissioning, check the remote control system and the model for proper operation and visible damage, such as: defective plug connections or damaged cables. All moving parts must work easily, but without bearing.
Check that all screw and plug connections, wheel nuts and electrical contacts are secure, as these can get loose during transport, during driving or during minor accidents.
Fasten long cables so that they can not get into moving / rotating parts. Cables must not be kinked.
Please observe the separate operating instructions for possible accessories.

Battery and Charger

Please use only special battery chargers and batteries. Get advise in a model building store. Never store your batteries when they are fully charged.

• Keep batteries / rechargeable batteries out of the reach of children and pets, as they can inadvertently swallow the batteries / accumulators. In this case, immediately consult a doctor!
• Expired or damaged batteries can cause burns in contact. If skin or eyes get in contact with the electrolyte, rinse immediately with clean water and seek medical attention. Use suitable protective gloves when disposing of defective battery.
• If you notice any signs of smell, discoloration, excessive heating or deformation of the battery, disconnect the battery immediately from the charger or the consumer. Dispose of the battery!
• Conventional alkaline batteries (1.5V) are intended for single use only and must then be properly disposed of.
• Dispose of empty batteries or defective batteries enivronmetally correctly at the authorized collection points. Disposal over household waste is prohibited!
• Batteries must not become moist or wet. Also avoid the formation of condensation water.
• Never expose the batteries, the charger or the model to adverse environmental conditions (eg wetness, high or low ambient tempera- ture, sources of ignition or open fire, dust, vapors, solvents)!
• Also avoid strong contamination as well as excessive mechanical stress on the battery, never tug on the connection cables!
• Never mix batteries and rechargeable batteries in one unit at the same time! Use only batteries or only rechargable batteries.
• If no brand-new batteries are used for the power supply of the transmitter, pay attention to a sufficient remaining capacity (battery tes- ter).
• When using rechargeable batteries instead of batteries, the lower voltage (batteries = 1.5V, rechargeable batteries = 1.2V) and the lower capacity of rechargeable batteries will affect the operating time and the range.
• Always replace the complete set of batteries, not just individual cells. Always use batteries of the same type and manufacturer.
• Do not mix batteries with different charge levels. The weaker batteries / rechargeable batteries with lower capacity could be deep-dischar- ged and leak.
• When inserting batteries or rechargeable batteries into the battery holder, ensure correct polarity.
• Incorrect polarity will damage not only your model, but also the battery. Batteries / accumulators must never be short-circuited, dama- ged, disassembled or thrown into open fire.

There is a risk of fire and explosion!
Disconnect the battery immediately from the charger when the battery is hot!
If the model is not used for a long time, remove the inserted batteries or rechargeable batteries from the remote control unit and from the model in order to avoid damage from discharged / deep discharged batteries.

Notes on charging

Charge the battery/ies immediately before use. Never charge them:

• in the model
• in your motor vehicle
• unattended
• with chargers that are not suitable
• Charge batteries only on fireproof surfaces

General Safety Notes

• Check regularly that all screws are firmly seated, as they can get loose by impacts and vibrations.
• Tires should not show cracks or damage.
• Check the connections for correct contact and damage.

Water Resistant

The MODSTER Desert Rookie can be operated under humid conditions as his motor, regulator and servo are splash-proof. Splash-proofed means only that a device can withstand water sprays, but it must not be immersed in water, or exposed to excessive humidity or strong rain for a long time.
The vehicle must never be immersed completely in the water.
Driving in wet conditions also requires additional maintenance. The transmitter is not splashproof. Please protect it from rain and water. After driving, remove all water and dirt from the vehicle and completely dry the vehicle. Ball bearings, metal parts and swing pins must be lubricated after driving in a humid environment.

Information

The model is an all-wheel-drive RC car chassis with a built-in Brushed Electric Motor and a 2.4 GHz receiver, a programmable electronic driving controller and a steering servo.
The RC model is pre-mounted ready for use and comes with a remote control transmitter.
The model is intended for both indoor and outdoor use.
The chassis is light and torsion-resistant. The encapsulation protects the transmission from dirt and stones.

The electronic trolley is optimally tuned to the engine and impresses with its excellent starting behavior, acceleration and constant running characteristics. The powerful steering servo has a high positioning torque and high positioning speed with maximum stability. A servo saver also protects the servo against violent impacts against the wheels. With the 2.4 GHz remote control system, you have a radio remote control system that is ideally suited for model cars and model ships. Two control functions can be operated remotely via the proportional function channels. The 2.4 GHz transmitter and the receiver tuned to it do not operate on a frequency fixed by transmitter and receiver quartz. Transmitters and receivers scan the frequency band after an available, free frequency, after which the radio connection is established.

Intended Use

The product is designed exclusively for private use in the model building sector and with the associated operating times. This product is not approved for commercial or industrial use or for continuous operation. Improper use can lead to the risk of injury to persons as well as to damage to the product and the associated hazards, e.g. loss of control over the model, short circuit, fire, electric shock, etc. Observe the safety instructions in this manual. These contain important information on handling the product. The product is suitable for children under 14 years of age only under adult supervision.

Dispose of the model, battery and charger at the end of their life according to the legal regulations.
Please avoid longer full throttle rides and allow the motor, ESC and battery to cool down between rides!

USB-Charger:
Please connect the USB charging cable to a USB port with at least 1.5 A, e.g. Computer, USB power supply, power bank, etc.
Now connect the standard rechargeable battery to the USB charging cable.
A red LED in the USB connector starts lightning – this indicates the charging process.
As soon as the battery is fully charged, the red LED turns off.
The charging process is finished now, please disconnect the battery charger cable and the charging cable from the USB power source.

Binding procedure of transmitter and receiver

The binding between transmitter and receiver was done in factory. However if you want to re-bind please follow this instruction:

1. Transmitter and receiver must be off.
2. Switch on the receiver by connecting the battery next do the ESC-cable
3. Switch on transmitter within 5 seconds.
4. The receiver`s LED will blink for 3-8 seconds.
5. When the LED stops blinking, the binding is done successfully.

Contents

• Built up and ready to run model
• 2,4 GHz transmitter
• Steering servo
• Electric motor
• ESC – waterproof
• USB-charger
• Battery
• Manual

Technical details

How-to-start Guide

1. Put 4 pcs mignon AA batteries in the transmitter & take care of the polarity!
   not included

2. Move the ESC power switch to the “ON” position, the LED will be on.
   

3. To slowly drive forward, pull the throttle trigger slightly. Adjust the speed by pulling the trigger. Push the trigger to brake/reverse. Release the trigger to keep your vehicle still
   

4. Plug the ESC cable to the battery cable to switch ESC on
   

5. Use the steering trim dial to adjust the neutral position of the servo. Push the dial counter-clockwise to trim left, clockwise to trim right, until your vehicle tracks straight when steering at neutral position.
   

6. If the direction of travel on the rudder is opposite, slide the steering reverse switch to the other position.
   WARNING: Do NOT slide the throttle reverse switch unless you completely understand this function and it is necessary to switch. Otherwise serious damage may occur.
   

7. Adjust the servo angle by turning the switch up or down.
   Turn the switch to upper position for larger servo angle.
   Turn the switch to lower position for smaller servo angle.
   

8. After you finished, turn off ESC power, then unplug battery and put in a dry safe place to cool down before you use it again.

Running Tips:

1. Run your vehicle on a flat surface, and keep your vehicle in sight.
2. Always release the throttle trigger right away following a crash to prevent further damages.
3. Do not run your vehicle in an area with people or property nearby.
4. When you finish, always turn off your transmitter AFTER your vehicle power.
5. Always keep the battery unplug when you are not attempt to run the vehicle.

Disposal

Dispose of the product at the end of its service life in accordance with the applicable legal regulations.

Batteries

| You as an end user are obliged by law (battery ordinance) to return all used batteries and accumulators; Disposal over household waste is prohibited! The symbol at the end indicates the prohibition of disposal via household waste. Batteries are also marked with the designation for heavy metal: Cd = cadmium, Hg = mercury, Pb = lead. You can dispose of used batteries / accumulators free of charge at the collection points of your municipality or anywhere where batteries are sold. They fulfill the statutory obligations and make your contribution to environmental protection.
---|---

Error solution

RC system does not work| Check whether the system is switched on. Check the charge status of the batteries / accumulators of the transmitter and the receiver. Check the polarity of the batteries / rechargeable batteries. Check the contacts and plug – in connections of the receiver batteries / accumulators
---|---
Transmitter switches off immediately or after short time| Check the charging state of the transmitter‘s batteries
After switching on a warning signal of the ESC sounds, motor does not run| Input voltage faulty, check the vehicle‘s battery
After switching on, the red LED lights constantly, motor does not run| Throttle/Break signal faulty. Check the connection between receiver and ESC
RC System has only a small range| Check the charging state of the batteries of transmitter and receiver, charge, if necessary or replace.
RC system works faulty| Interference pulse
A plug is loose
Receiver is defect (eg after a crash)
One or more electrical / electronic components have come into contact with moisture
Check cummonication of transmitter/receiver
Servo / ESC does not react| Check whether the RC system is on. Check the charging state of the batteries of transmitter and recei-
ver. Check the polarity of the servo plugs.
The servos are trembling| Check the charging state of the batteries of transmitter and receiver. Check whether moisture has come in contact with the receiver and, if necessary, carefully dry with a hot air fan.
Servo is humming| Check the charging state of the batteries of receiver. Check the smooth operation of the articulated linkages. Remove the servo and test for function.
Servos do not respond properly| Batteries of transmitter or receiver are weak
Gear wheels in the servo gear do not work or are defective Adjusting rings on the link levers are loose
Reverse switch on the transmitter was inadvertently switched to „REV“ Check the charge status of Fahrakku and Senderakkus
The model does not respond Motor does not start even though the servo is responding| Motor does not start even though the servo is responding; Motor is defective Motor cable loose, motor becomes too hot

Declaration of Conformity

Declaration of Conformity in accordance with the Radio Equipment Directive (RED) 2014/53/EU

hereby declare that the product
MODSTER Rookie
MODSTER Desert Rookie

Product number:  218005
249207

Complies with the essential requirements and the other relevant provisions of the Directive (RED) 2014/53/EU, when used for its intended purpose.

ETSI EN 300 440 V2.1.1
ETSI EN 301 489-1 V2.1.1
ETSI EN 301 489-3 V2.1.1
EN 62479: 2010

Manufacturer I responsible Person : MSG Online Gmbli, Walter Bittdorfer
Wirtschaftspark 9
8530 Deutschlandsberg, Austria

managing director

place of issue/ date: Deutschlandsberg (Arustria), 16.08.2019

Frequency Range: 2405 MHz to 2475 MHz
Sending Level< 20 mW (13dBm)

The EIRP of the EUT is -11 .25d8m {0.08mW), which is below the max. permitted sending level of 20 mW. Therefore the EUT is not required to conduct SAR measurement.

References

• MODSTER

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>