MODSTER S2 SUV E-LONGBOARD Electric Skateboard User Manual

MODSTER S2 SUV E-LONGBOARD Electric Skateboard

Thank you for buy our electric skateboard Do note that an electric skateboard is not a toy. Please take time to learn it and read this manual carefully. Particularly the safety instruction pages. We hope you will enjoy this product and have lots of fun with it in the future

Preparation

1. Be sure that wear a helmet and safety gear when you ride it
2. Confirm the front direction of the skateboard
3. Confirm the position on the skateboard, The feet stand on the widest front and back skateboard.
4. Please start with the low speed mode to be familiar with the accelerate and brake of the skateboard.
5. Please stop riding by remote control brake operation.then get down your front foot at first and then get down your back foot.

Parts Diagram

1. 6inch silicone wheel
2. 9inch front truck
3. Battery case
4. Charge port
5. Deck
6. Controller case
7. Belt motor
8. Tire with gear
9. Belt
10. Battery indicator
11. Power button

Remote Control

Pair Instruction

• At the first step, the Board and Remote must be paired. Before starting, to ensure the Board and Remote are turn off.
• Turn on the board
• Press the power button for 5 seconds, then the power button light will flash
• Turn on the remote,then press the pair  button. the signal indicator will flash and  the power button light will flash with same frequence. Then means the paired successfully.
• Push the joystick, forward to test the accelarate and backward to test the brake. After tested all function work normal you can start your riding.

Switch Tires

1. 83 wheels
2. wheels with Pulley
3. 250mm belt
4. T-type wrench

Use T-wrench pulley to remove the wheel nut and ring
(A). Front wheel

1. Remove the tire
2. Put the 83 wheel at the
3. Put the wheel nut and ring truck back then use T-wrench to tighten the nut

(B). Back wheel

1. Pushing the belt to other side and rolling the lire at the same time to take off the belt
2. Take off the tire
3. Remove the belt from the gap between pulley and belt cover
4. Put the belt-250 (No.3 at the pie 1.0) at the motor pulley
5. Put the wheel with pulley (NO.2atthe pie 1.0) on the truck
6. Engage the belt
7. Put the wheel nut and ring back.then use T-wrench to tighten the nut

SPECIFICATION

SAFETY INSTRUCTIONS

• The electric skateboard is not a toy, should be treated With appropriate caution. Always practice safety first-as
• It is possible to lse balance and cause a collision or tall.
• Ensure that you use the board in a sate appropriate environment, and always wear appropriate safety gear
• Safety Gear: we recommend that you wear full safety gear while riding. Please wear a suitable skateboard helmet, elbow pads, knee pads, and gloves.
• Wear shoes: Flipflops or similar loose footwear are not suitable for riding wear.
• The skateboard is designed for rider over 14 years old and above.
• Only one person riding for each skateboard at a time.
• The maximum load of the board is 150kg. Exceeding this weight will compromise the structural integrity of the skateboard, as well as remote and functionality,and may cause board damage, losing control or other breakage.
• Please observe your local traffic laws and regulations.
• The board is designed to drive on flat and paved Surtaces.Avoid driving on sand, gravel,mud, rugged or open ground. Do not drive on slippery ground, such as snow, ice or wet ground.
• Keep fingers, hairs, and clothing away from motors, wheelsand moving parts.
• Do not open or tamper with electronics housing.
• Electricshock is possible and this also voids the warranty.
• Caution: do not store the board with empty battery charge the battery at least all 3 month.

MSG Online GmbH

Declaration of Conformity in accordance with the Electromagnetic compatibility (EMC) 2014/30/EU
Comply with the essential requirements and the other relevant provisions of the Directive (EMC) 2014/30/EU

1. EMC Directive 2014/30/EU
   EN-61000-3-3:2013 +A1:2019
   EN-55032
   EN 301 489-1 V2.2.0 (2017-03)
   EN 301 489-17 V3.2.0 (2017-03)

2. Machinery Directive 2006/42/EC
   EN ISO 1210:2010
   EN 60204-1:2006 + A1:2009

3. Low Voltage Directive 2014/35/EU (For Charger)
   EN-60335-1:2012 + A11:2014
   EN 62233:2008

4. Radio and Telecommunication Terminal Equipment (RTTE) Directive 2014/53/EU
   (For remote Control)
   EN 300 220-1 V2.4.1 (2012-05)
   EN 300 2020-2 V2.4.1 (2012-05)
   EN 301 489-1 V2.2.0 (2017-03)
   EN 301 489-17 V3.2.0 (2017-03)
   EN 300 328 V2.1.1 (2016-11)

5. RoHs Directive
   2011/65/EU

6. Health
   EN-62311:2008
   chureiqhafer

Range information, as well as information on maximum speeds and incline ability are heavily dependent on parameters Such as the state of charge of the battery, condition of the ground, inclines or declines during the route, weight of the person driving, physical performance by diving or, if available, use of the pedals, weather conditions, headwind and depending on other factors. Our information relates to the optimal case
To the current version ot the operating instructions visit our website: WWW.MODSTER.AT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>