MODSTER M280326 64mm Marlin Elektromotor Jetmodell User Manual

MODSTER M280326 64mm Marlin Elektromotor Jetmodell

Warning: This manual contains important information that will help you maintain and operate your model aircraft in a reliable and safe manner. Please read the instructions and warnings carefully prior to assembly, setup or use. As this model aircraft is a sophisticated hobby product, it must be flown with safety and common sense in mind, failure in doing so may result in injury or property damage. This product is not intended for use by children without direct adult supervision.

Safety precautions and warnings

• As the user, you are solely responsible for the safe operation and maintenance of this product. Follow the directions and warnings listed in this manual, as well as that of supporting equipment (chargers, batteries etc.) and always use common sense.
• This is not a toy. Not for children under 14 years of age.Always operate your model in an open area away from buildings, cars, traffic or people. Never operate near people-especially children who can wander unpredictably. Never operate in populated areas for any reason, where injury or damage can occur.
• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
• Never catch the aircraft while it is in flight, the structure of the fuselage was not designed and protected for this purpose. Never operate your model in bad weather, including in excessively windy or precipitating conditions.
• Never operate your model with low transmitter batteries.
• Keep your throttle quadrant in its lowest position prior and after every flight. Use the throttle cut function if able. Always use fully charged batteries and move batteries before disassembly.
• Avoid water exposure to all equipment not specifically designed and protected for this purpose.
• Avoid cleaning this product with chemicals.
• Never lick or place any part of your model in your mouth as it could cause serious injury or even death.
• Keep all chemicals, small parts and anything electrical out of the reach of children.

Introduction
Arrows Hobby 64mm Marlin- The perfect entry-level jet!
As a successor to the Arrows Hobby lineup of WWII warbirds and trainers, the Arrows Hobby engineers have decided to tackle the impossible- a jet that flies as easily as the best high winged trainers on the market. After a lengthy development process, Arrows Hobby is proud to announce the super easy-to-fly Marlin!
Engineered to have inherintly stable, predictable and high-lift flight characteristics, the Marlin is a fantastic way to enter the world of jets. The 2840 motor, 40A ESC and a 11 bladed 64mm EDF unit ensures ample power whenever necessary and a fantastic engine note at all times. Structurally, no glue is required to assemble the Marlin.

The screw-together assembly significantly increases relate rigidity while reducing build time. A full flying horizontal stabilizer ensures precision pitch movements and full ball links ensure smooth surface movements all around. The newly designed landing gear absorbs even the hardest landings. A latch-type canopy makes in flight canopy loss a thing of the past.
For those who love jets but have never tried to fly one, the Marlin is your ticket into the world of electric jets!

Features

• Sleek aerodynamic airframe
• Screw together assembly
• Full flying horizontal stabilizer
• Ball linkages
• Latch type canopy
• Full digital servos
• Ultra durable EPO foam
• The perfect beginner jet

Specifications

Kit contents

Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit with labels. If any parts are missing or defective, please identify the name or part number (refer to the spare parts list near the end of the manual) then contact your local shop.

• A: Fuselage
• B: Main wing set
• C: Horizontal stabilizer
• D: Canopy
• E : Landing gear set
• F: Screws

Model assembly

Wing installation

1. Attach the wing onto the fuselage, ensuring not to pinch any of the servo wires.
2. Secure the wing to the fuselage with included screws as shown. Do not over tighten the screws.

Landing gear installation

1. Insert the landing gear assembly into the wing landing gear slot and pivot 90 degrees to lock the landing gear in place.

Horizontal stabilizer installation

1. Connect the elevator servo connectors to the servo extensions in the fuselage.
2. Attach the horizontal stabilizer in the rear of the fuselage and secure it in place using the included screws. Ensure the control horn faces down as shown.

Battery installation

1. Remove the battery hatch.
2. Remove the hook and loop tape from the fuselage. Apply the looped surface to the battery.
3. Install the battery into the fuselage- securing it with the preinstalled battery straps.
   Note: The weight of each battery may vary due to different manufacturing techniques. Move the battery fore or aft to achieve the optimal center of gravity.

Receiver diagram

The cables from the servo connector board should be connected to your receiver in the order shown. Note that the LEDs can be powered by any spare channel on the receiver. Tuck the wire leads into the recessed cavity towards the rear of the battery hatch.

Preflight check

Important ESC and model information

1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps. Several beeps with the same tune means the ESC has detected the cells of the battery. The count of the beeps equals the cells of the battery. The motor is now armed and will start when the throttle is moved.
2. The motor and ESC come pre-connected and the motor rotation should be correct. If for any reason the motor is rotating in the wrong direction, simply reverse two of the three motor wires to change the direction of rotation.
3. The motor has an optional brake setting. The ESC comes with brake switched off and we recommend that the model be flown with the brake off. However, the brake could be accidentally switched on if the motor battery is connected to the ESC while the throttle stick is set at full throttle. To switch the brake off, move the throttle stick to full throttle and plug in the motor battery. The motor will beep one time. Move the throttle stick to low throttle or the off position. The motor is ready to run and the brake will be switched off.
4. Battery Selection and Installation. We recommend the 4S 2200-2600mAh 35C Li-Po battery. If using another battery, the battery must be at least a 4S 2200-2600mAh 35C battery. Your battery should be approximately the same capacity, dimension and weight as the 4S 2200-2600mAh 35C Li-Po battery to fit the fuselage without changing the center of gravity significantly.

transmitter and model setup

After assembly and prior to your first flight, make sure all control surfaces respond correctly to your transmitter by referring to the diagram below.

Control throws
The suggested control throw setting for the Marlin are as follows (dual rate setting):

Tip: The maiden flight should always be flown using low rates, fly the aircraft until you are familiar with its characteristics prior to trying high rates. Make sure the aircraft is flying at altitude and adequate velocity prior to using high rates, as the aircraft will be sensitive to control inputs with the larger control surface movements.

 |  |
---|---|---
Elevator| 12mm up / down| 10mm up / down
Aileron| 14mm up / down| 12mm up / down
Rudder| 10mm left / right| 8mm left / right

Clevis installation

1. Pull the tube from the clevis to the linkage.
2. Carefully spread the clevis, then insert the clevis pin into the desired hole in the control horn.
3. Move the tube to hold the clevis on the control horn.

Control horn and servo arm settings

1. The table shows the factory settings for the control horns and servo arms. Fly the aircraft at the factory settings before making changes.
2. After flying, you may choose to adjust the linkage positions for the desired control response.

Finding the center of gravity

Before flying the model

Find a suitable flying site
Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields – a flying field specifically for R/C planes is best. Never fly near people – especially children, who can wander unpredictably.

Performing a range check
A radio range check should be performed prior to the first flight of the day. This test may assist you in detecting electronic problems that may lead to a loss of control- problems such as low transmitter batteries, defective or damaged radio com-ponents or radio interference. This usually requires an assistant and should be done at the flying site.

Always turn your transmitter on first. Install a fully charged battery in the battery bay, then connect it to the ESC. In this process, make sure that the throttle cut functionality is on, and that the throttle stick is secured in its lowest position- other-wise, the propeller/fan will engage and possibly cause bodily harm.
Note: Please refer to your transmitter manual that came with your radio control system to perform a ground range check. If the controls are not working correctly or if anything seems wrong, do not fly the model until you correct the problem. Make certain all the servo wires are securely connected to the receiver and the transmitter batteries have a good connection.

Monitor your flight time
Monitor and limit your flight time using a timer (such as a stopwatch or on the transmitter, if available). As modern Lithium Polymer batteries are not designed to discharge completely, when the battery runs low, the ESC will lower then completely cut the power to the motors to protect the battery.Often (but not always) power can be briefly restored after the motor cuts off by holding the throttle stick all the way down for a few seconds.To avoid an unexpected dead-stick landing on your first flight,set your timer to a conservative 4 minutes. When your alarm sounds you should land right away.

Flight tips

• Take off
  Point the aircraft into the wind while slowly applying power until the aircraft starts to track straight, use the rudder when necessary. When the aircraft reaches takeoff speed, ease back on the elevator stick until the aircraft is climbing at a constant rate without decelerating. Climbing at too steep of an angle at the relatively low speeds of a takeoff-climb may result in an aerodynamic stall.

• Flying
  Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards, or soccer fields. Consult laws and ordinances before choosing a location to fly your aircraft. After takeoff, gain some altitude. Climb to a safe height before trying technical manoeuvres.

• Landing
  Land the aircraft when you start to feel sluggish motor response. If using a transmitter with a timer, set the timer so you have enough flight time to make several landing approaches.The model’s three point landing gear allows the model to land on hard surfaces. Align model directly into the wind and fly down to the ground. Fly the airplane down to the ground using 1/4-1/3 throttle to keep enough energy for proper flare. Before the model touches down, always fully decrease the throttle to avoid damaging the propeller or other components. The key to a great landing is to manage the power and elevator all the way to the ground and set down lightly on the main landing gear. With some practice, you will be able to set the aircraft gently on its main gear and hold it that way until the speed reduces enough where the nose wheel (tricycle landing gear aircraft) or tail wheel (tail draggers) settles onto the ground.

• Maintenance
  Repairs to the foam should be made with foam safe adhesives such as hot glue, foam safe CA, and 5min epoxy. When parts are not repairable, see the spare parts list for ordering by item number.
  Always check to make sure all screws on the aircraft are tightened. Pay special attention to make sure the spinner is firmly in place before every flight.

Troubleshooting

ESC is not armed.

Throttle channel is reversed.

| Lower throttle stick and throttle trim to lowest settings.

Reverse throttle channel on transmitter.

Excessive vibration or propeller noise.

| Damaged spinner, propeller, motor or motor mount.

Loose propeller and spinner parts. Propellor installed backward.

| Replace damaged parts.

Tighten parts for propeller adapter, propeller and spinner.

Remove and install propeller correctly.

Reduced flight time or aircraft underpowered.

| Flight battery charge is low. Propeller installed backward. Flight battery damaged.| Completely recharge flight battery.

Replace flight battery and follow flight battery instructions.

Control surfaces are unresponsive or sluggish.

|

The control surface, control horn, linkage or servo damage.

Wire damaged or connections loose.

|

Replace or repair damaged parts and adjust controls.

Do a check of connections for loose wiring.

Controls reversed.

|

Channels are reversed in the transmitter.

|

Do the control direction test and adjust controls for aircraft and transmitter.

Motor loses power

Motor power pulses then motor loses power.

| Damage to motor, or battery. Loss of power to aircraft.

ESC uses default soft Low Voltage Cutoff(LVC).

|

Do a check of batteries, transmitter, receiver, ESC, motor and wiring for damage(replace as needed).

Land aircraft immediately and recharge flight battery.

LED on receiver flashes slowly.

|

Power loss to receiver.

| Check connection from ESC to receiver. Check servos for damage.

Check linkages for binding.

Spare parts list

Disclaimer of Warranties:

• This model must not be used by children younger than 14 years

• It contains small parts that could be swallowed

• Keep hands, face, hair and loose clothing away from the propeller

• Do not reach into rotating parts

• Always disconnect the battery connector after the flight and remove the battery

• Only fly where it is safe and where you do not endanger third parties

• Keep the operating instructions in a save place and read them carefully and completely before using the model.

• We recommend people with no knowledge of model flying to commission the model under the guidance of an experienced pilot

• Before each flight, test the range of the remote control and the charge status of the rechargeable battery and check the batteries or rechargeable batteries in the remote control.
  Do not fly…

• near crowds of people,

• towards people or animals,

• in poor visibility,

• near high-voltage lines or radio masts

• during thunderstorms, rain, snow or in a damp environment.

1.  Always keep the aircraft in sight and under control.
2. Always use fully charged batteries/rechargeable batteries.
3. Always switch on model first, then the transmitter, and always switch off model first, followed by the transmitter.
4. Do not use the model if it is visually or mechanically damaged.
5. Always check all screw connections and structures for tightness and damage
6. Never reach into the rotating propeller – risk of injury!
7. Always disconnect and remove the flight battery from the model after the flight.
8. Always charge and store the battery outside of the model, charge on a non-flammable surface, never store the battery in the model. Never charge batteries unobserved!
   Check about the legal provisions applicable in your country

FIRMENBUCH GRAZ FN315230Z • UID-NR. ATU 64361513 EVA-PARTNERNUMMER: 152216
ARA LIZENZNUMMER: 177 49 • GRS NUMMER: 110072576 INTERSER0H HERSTELLER ID [EARJ: 152204
WEE REG.-NR. DE 44576630

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>