MODSTER MD10190 Fold 4K Foldable Drone RTF Combo User Manual

June 4, 2024
MODSTER

MODSTER logo

MODSTER logo 2

User Manual

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo

CAUTION:
The drone can be controlled both via the controller and via the mobile phone app. If the transmission contact to the controller is interrupted, the app takes over control as long as the drone is still within range of the mobile phone.
Reconnecting the controller during the flight is not possible. To do this, the drone must be landed and reinitialized. If the drone falls outside the transmission range, it lands automatically.

Introduction

We are very happy that you have decided for a MONSTER Product and we are sure that you will have a lot of fun with the MONSTER FOLD 4K! You have made the right decision when it comes to product quality and spare parts supply. All of our products get carefully checked for completeness and function. Our products comply with the guidelines and norms required in the EU and Germany. We hope you will have great fun with our products. To ensure your safety, please read the entire introduction before first using the product. This product introduction explains the most important indications, which should be followed. This introduction provides you with tips on maintenance of your MONSTER FOLD and describes the correct operation of the copter for secure and long-term use. All the information is based on the technical state of the time when this introduction was composed. Changes and additions carried out in the meantime are not included and described in this manual. You will find the latest version of the manual on www.modster.at. We are at your disposal for further questions or if there are any problems. Please contact us via phone or under info@modster.at.

Caution
Ignoring the instructions of this manual may cause damage or injuries!
Caution -> Ignoring these instructions can trigger dangerous situations!
Read this instruction completely before starting the copter! It helps you to get familiar with secure flying. Nobody should ever fly this copter without reading and understanding the instructions.

Disclaimer of warranties:

  • This model must not be used by children younger than 14 years
  • It contains small parts that could be swallowed
  • Keep hands, face, hair, and loose clothing away from the rotors
  • Do not reach into rotating parts
  • Always disconnect the battery connector after the flight and remove the battery from the model!
  • Only fly where it is safe and where you do not endanger third parties
  • Keep the operating instructions in a safe place and read them carefully and completely before using the model.
  • We recommend people with no knowledge of model flying to the commission under the guidance of an experienced pilot
  • Before each flight, test the range of the remote control and the charge status of the rechargeable battery and check the batteries or rechargeable batteries in the remote control.
  • Do not fly near crowds of people, towards people or animals, in poor visibility, near high-voltage lines, radio masts or during thunderstorms rain, snow or in a damp environment.
  1. Always keep the aircraft in sight and under control.
  2. Always use fully charged batteries/rechargeable batteries.
  3. Always switch on the model first, then the transmitter, and always switch off the model first, followed by the transmitter.
  4. Do not use the model if it is visually or mechanically damaged.
  5. Always check all screw connections and structures for tightness and damage
  6. Never reach into the rotating rotor – risk of injury!
  7. Always disconnect and remove the flight battery from the model after the flight.
  8. Always charge the battery outside of the model, charge on a non-flammable surface, never store the battery in the model.
    Never charge batteries unobserved!

Check about the legal provisions applicable in your country

Safety Instructions: Batteries

  • Always store the batteries out of reach for children!
  • Non-rechargeable batteries shall not be used!
  • Rechargeable batteries need to be taken out of the model or the controller before charging
  • Unequal batteries, as well as new or used batteries, shall not be used together
  • Only recommended or some of the same types are allowed to be used
  • Empty batteries need to be taken out of the controller
  • Connecting terminals shall not be short-circuited
  • Batteries need to be taken out of the controller if it is not going to be used for a longer time
  • The model is equipped with a rechargeable Lipo battery
  • Only recharge the battery with the delivered or another suitable charger
  • Always use a fireproof desk pad during the charging process
  • Do not leave the battery unattended during the charging process
  • The battery always has to be fully charged
  • Never disconnect or short-circuit the contact points of the battery
  • Never damage or change the contact points of the battery
  • Never damage the battery mechanically (Explosion Danger!)
  • The battery shall not get near children unattended
  • The model shall not be changed structurally!
  • Switch off the model and sender after usage (remove the battery from the model!)
  • Children shall only use this model under the suspension of adults
  • Leaking or damaged batteries can cause chemical burn when getting in contact with them
  • If skin or eyes get in contact with them, immediately contact a doctor and first aid

CAUTION:

  1. Keep the aircraft in sight and under control.
  2. Always use fully charged batteries.
  3. Always first turn on the model, then the transmitter, and always first turn off the model, then the transmitter.
  4. Do not use the model if it has optical or mechanical damage.
  5. Never reach into the rotating rotor, risk of injury!
  6. After the flight, always disconnect and remove the flight battery from the model.

Before Flying

The transmitter:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo -
transmitter

Setting up the controller/drone:
Installing the controller batteries.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo -
controller

  1. Unscrew the battery cover and insert 3 AA batteries, making sure you insert them following the correct polarity as shown.
  2. Re-attach the battery cover

Notice:
Always have an adult install the batteries.
Always use alkaline batteries and never mix old and new batteries.
Folding the arms:
Fold the arms according to the order of numbers, which is shown in the picture below:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - Folding the
arms

Install the Protector:
Pull the accessory (Pic 1) and press the locking plate on the protector, as the same time push in the protector (Pic 2).

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo -
Protector

Charging the Drone Battery:

Battery Warning:
Lithium Polymer batteries can expand, burst or catch fire if used incorrectly, causing both property damage and/or personal injury. It is essential to follow all the included instructions and safety warnings in full. The manufacturer, distributors, and retailers will assume no liability for the failure, which might comply with these safety instructions and warnings.

Instruction when Charging:

  1. The battery must be removed from the product before charging.

  2. If the battery has just been used, please let it cool down to room temperature before charging.

  3. Charging must only be undertaken by an adult and only using the charger included with this product.

  4. Always charge the battery on a non-flammable, heat-resistant surface with non-flammable surroundings.

  5. Connect the battery to the USB charging cable.

  6. Connect the USB charging cable to your USB charging devices the red LED on the battery will light up while charging and will turn off once the battery is fully charged. It takes around 60-70 minutes to fully charge the battery. Never continue to charge the battery after the red LED has turned off. Charging the battery completely you will need at least 10 minutes.
    MODSTER MD10190 Fold 4K Foldable Drone RTF Combo -
Charging

  7. Lithium Polymer batteries do not last forever. If your battery becomes damaged in a crash or no longer charges properly, immediately replace it with a new battery. To prolong the life of your battery it is always best to retain a bit of charge in your battery prior to charging it.

Sale Flight Environment:

  1. Make sure that the surrounding area is free of people, pets, or other obstacles before you start to fly.
  2. The drone is designed for outdoor or indoor flying depending on how much space is available.
  3. Always leave 1,5 meters between you and the drone

 Setup

Setting up the signal connection.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo -
signal

Step 1: Insert the battery to the battery housing (first picture). Turn on the power switch of the drone – the LEDs on the Drone will start to flash. Place the drone down on a flat surface, making sure the drone is facing away from you.

Step 2: Press down the controller power switch to turn on the power. The controller will make one short beep sound and the red LED will flash. To pair the si-gnals of the vision drone and the controller, you must RAISE the UP/DOWN lever on the controller all the way to the top. And then LOWER it to the bottom. It will make one short beep
sound. The next time you RAISE the UP/ DOWN lever the drone will lift into the air.

Step 3: Always turn off the power switch of the drone after flight
Step 4: Always turn the controller off after flight and remove all the batteries if you leave it unused for a long period of time.

Step 5: Please remove the battery by pressing down the tap on the battery and extracting the battery. The first attempts could be more sluggish than the next ones.

When flying outdoors, press the,, Speed button“ three times to set the third speed.

  1. Adjust the frequency.
  2. Calibration
  3. Start your flight.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
4

Match the Frequency

Turn on the drone and remote control after the drone LED light blinks quickly. Push the left stick of the remote control to the highest point and then pull to the lowest point. After the remote control send a „beep“ sound the frequency matching is finished and the drone LED light becomes steady.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
5

Auto Trim Function

Push both control sticks to the position as shown in the picture and hold them for a few seconds. The lights on the drone will start to flash. Now the drone is recovered to its original factory settings and ready to fly again.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
6

Auto-Hover

Start your first flight:
Push both control levers to the positions shown in the picture and hold them for a few seconds. The lights on the drone will start to flash. The motor starts working.

Auto-Hover:
After pushing the „take-off/landing“ button, the drone will automatically go up in the air and stay at a height of around 1.5 meters. After this step, push the left stick to keep the drone at any height you want. Press the „take- off/land“ button again. Then the drone will slowly land and finally, the motor stops spinning.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
7

Emergency Button:
In case the drone crashes against the wall or hits a tree, you can press the „stop“ button (2) . At the same time, the motor will stop spinning. Make sure there are no people below the flying drone.

Flight Control

Please us the controller to practice simulated flights before the drone takes off the first time.
Place the drone on a flat surface, making sure that the yellow LED lights are facing away from you.

| When you move the UP/DOWN lever up and the drone goes up, do this slowly. You should acquire a specific
kind of sensitivity in regard to the use of the drone. When you move the lever down, the drown will also go
down.
---|---
| When you move the TURN LEFT/TURN RIGHT lever in the left direction, the drone will move left. When
you move the lever right, the drone will also move right.
| When you move the FORWARD/BACKWARD lever up, the drone will start to fly forward. Please do this
slowly to acquire a kind of sensitivity in regard to the drone. When you move the lever down, the drone will
move backward.
| When you move the BANK LEFT/BANK RIGHT lever into the left direction, the drone will start to bank left.
Please to this slowly to acquire a kind of sensitivity in regard to the drone. When you push the lever in
the right direction, the drone will also bank right.
| Situation| Cause| Way to deal
---|---|---|---
1| The drone does not respond| 1. Drone enters low-pressure mode.
2. The remote control is low and the power indicator flashes| 1. Charge the drone.
2. Replace the remote control battery.
2| Drone reaction is not sensitive| 1. The remote controller is low on battery power.
2. The remote control with the same frequency is emitting interference.| 1. Replace the battery.
2. Go to a place without the same frequency emission interference.
3| Fly to one side when altitude hold/ Altitude hold unstable/Move up and down| 1.No horizontal correction.| 1. Recalibrate horizontally. See (Auto trim function)
4| Headless mode biased forward| 1. Multiple collisions cause bias.|  1. Redefine the front direction, see (Headless mode)

Flight Adjustment Section

When you lift your drone in the air without using any other buttons or levers, your drone should simply hover in one spot without moving in any other direction. However, if it does not do so, you can follow the instructions below to return to perfect hovering (TRIM). TRIMMING is always needed before your first flight.

| If your drone banks to the left, keep pushing the Bank Left/ Bank Right lever. Trim the button to the right until the drone stops banking.|
---|---|---
| If your drone banks to the right, keep pressing the Bank Left/ Bank Right lever. Trim the button to the left until the drone stops banking.|
| If your drone flies backward, keep pressing the forwards/backward lever. Trim the button up until the drone stops flying backward.|
| If your drone flies forwards, keep pressing the Forwards/ Backwards lever. Trim the button down until the drone stops flying forward.|

Flip Function

  1. Make sure the drone is flying at least 3 meters above the floor and 3 meters below the ceiling.
  2. Press the flip button on the controller. The controller will make a „Beep“ sound. Then flick the right-hand lever in a specific direction and the drone will flip in that direction.
  3. You may need to move the Up/Down lever up after the flip if your battery is low in order to keep your drone in the air.
    MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
19

Headless & One Key Return Funktion
Headless function: Press the Trim slider button on the left. you will enter the compass mode. Around exit compass mode press the same slider button.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
20

FLY PLUS quick start manual

Scan the QR-Code to get the download address: (Support IOS 10.0, Android 6.0 above systems)

http://www.lwcxtech.com/QRCode/AppQRCode/FlyPlus.asp

Lower visual optical flow positioning:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
21

Using instruction:

  1. Enter the ,, setting“ menu of your mobile device and turn on WIFI:
  2. Find the drone’s network and connect it.
  3. Open the Fly Plus“ software and in the control interface, you will see the real-time video.

Basic Interface:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
22

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
23

Click (Video effect) Menu as below picture show:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
24

Click,,More Settings“ Menu as the below picture show:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
26

Rocker:

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
27

Visual target following:

Dim light, strong light, black light, lens Angle, and distance will affect the following effect.
It is necessary to ensure that the target is in the real-time image and clearly visible.

MODSTER MD10190 Fold 4K Foldable Drone RTF Combo - fig
28

Gesture photo/video

Tips:

  1. Please aim the camera front on.
  2. Please use it in a well-lit environment
  3. Dim light, strong light, blacklight, environment, weak WiFi or interference will affect the effect when the best light is about 2m away from the lens.

Else:

  1. Aircraft calibration. Please place the aircraft on a horizontal plane and perform the calibration.
  2. It is forbidden to use one button to fly away or soar into the sky indoors.

Replacing Blades and Fixing Issues

Blade Replacement
Your drone blades are very strong, but sometimes they can get damaged by a bad crash. You have spare blades in the box and you are able to replace them. It is as easy as placing a new one back over the motor bar. You must always replace an A blade with an A blade and a B blade with a B blade.

The drone cannot be lifted or does not fly in your chosen direction

  1. The most common reasons for a drone that cannot be lifted or does not fly in your chosen direction are hair and debris wrapped around one or more of the blades. It is simple to remove these obstacles. Take the blade off and remove the debris and place the blade back on.
  2. The batteries in the drone may need charging and the batteries in the controller may need replacing.
  3. You may have knocked your trim button settings out of sync. Follow the instructions earlier in the booklet to reset them to the factory settings and then retrim as desired.

Warnings

  1. The Drone is designed for 14+
  2. Adult supervision is always advisable with any form of flying toys
  3.  Always ensure your flight area is free of all obstacles before taking off and ensure the Drone is always flown in excess of 1,5 meters from yourself
  4. Remove all batteries from the drone and controller when not in use
  5. Never overcharge
  6. Never leave the charger unattended
  7. Never touch the drone motors during or after flying as they can get hot
  8. Never touch the blades, when they are in motion
  9. If the drone is damaged, stop using it immediately
  10. Do not dispose of any parts of the drone or Controller in the normal rubbish. All Parts should be taken to your local recycling center
  11. The battery in the drone should never be exposed to any form of high temperature or disposed of in a fire

Disposing of exhausted batteries

The following instructions are addressed to those who use batteries or products with built-in batteries and do not resell them in the delivered condition.

  1. Exhausted batteries must never be thrown into household waste! You are legally required to return the exhausted batteries so that correct disposal can be guaranteed.
    You can hand them over at local collecting points or directly in the shop. As a retailer of batteries, we are required to take them back. Our take-back obligation for exhausted batteries is limited to batteries that were/are new batteries in our range. Old batteries of the type named above can therefore be returned to us either sufficiently postage paid or they can be delivered free of charge directly at our dispatch warehouse at the following address: MSG Online GmbH, Wirtschaftspark 9, AT-8530 Deutschlandsberg.

  2. Meaning of battery symbols
    Batteries are characterized by the symbol of a crossed waste bin (see below). This symbol indicates that batteries must not be disposed of in the household waste. For batteries that contain more than 0,0005 percent of Quicksilver, more than 0,002 percent Cadmium, or more than 0,004 percent lead, the chemical name of the used harmful substance can be found under the waste bin symbol – „Cd“ stands for Cadmium, „Pb“ for Lead, and Hg“ for Quicksilver.

  3. Starter Batteries
    The following special features apply when it comes to buying starter batteries: The seller is acc. § 10 BattG obliges a final deposit of € 7.50 including VAT if the end-user does not return the used starter battery to the seller at the time of the purchase of the new starter battery. The customer receives a pawn coupon when purchasing a starter battery. If the old starter battery is returned to a return point set up by the public waste disposal authority, the customer has to confirm the disposal by means of a stamp and a signature. Subsequently, the customer has the possibility to return this confirmation to the seller, with the identification of his customer number for the refund of the deposit. Alternatively, the customer can also hand over his old starter battery together with the Pfandschein to the reimbursement of the deposit directly at the seller. (Due to the Dangerous Goods Ordinance the dispatch of the old battery to the seller is not permitted.)

a) General
Dispose of the product at the end of its service life in accordance with applicable legal requirements.
b) (Rechargeable) Batteries
As an end user, you are obligated by law (battery ordinance) to return all used batteries and accumulators, disposal of household waste is prohibited! Batteries/accumulators containing harmful substances are marked with the symbol below, which indicates the prohibition of disposal via household waste. The designations for the heavy metal are Cd = cadmium, Hg = mercury, and Pb = lead (designation stands on battery, for example, under the rubbish symbols on the left). You can dispose of your used batteries free of charge at the collection points of your municipality, our branches, or wherever batteries are sold. They thus fulfill the statutory obligations and contribute to environmental protection.
WEEE ordinance
Electrical products do not belong as household waste. You can dispose of your old, used electrical products free of charge at the public collecting points of your municipality.

Safety Notes

Do not use your lithium polymer cells until you have read and fully understood all safety instructions. This lithium-polymer instruction booklet contains important safety instructions to avoid potential hazards that could lead to injury to persons or equipment. For damages caused by improper use, storage, and/or charge of the batteries, which are not in compliance with the safety regulations, we can not assume any liability or guarantee and do not pay any damages. The guarantee claim of an accumulator automatically ends with the manipulation by the acquirer. These include e.g. the removal of components (cables, heat shrink tubing, PCB), the self-assembly of individual cells into one pack, and the re-sol-dering of cables and boards. It is generally recommended to have special packs made exclusively by the manufacturer, as they can be used in a rational, high-quality manner and according to the safety conditions.

Storing: Never throw lithium polymer into water or expose it to moisture. Also, they must not be stored near fire, hot and/or hot places, in the sun or near combustible materials. Cells that heat to more than 60 degrees Celsius can destroy themselves or begin to burn. Therefore, always keep lithium- polymer batteries in a fire-proof place. Keep out of the reach of children! LiPo batteries should generally not be stored longer than one month. For longer storage, a battery should only be charged up to approx. 50-70%. Avoid short circuits: The poles of the lithium polymer battery / rechargeable battery must not come into contact with metal objects accidentally or deliberately, as this usually causes a short circuit! In the case of a short circuit, an extremely high current is generated in milliseconds, which can lead to overheating of the cell, leakage of electrolyte and consequently explosion and flame formation. Avoid swallowing electrolyte fluid or contact with eyes, skin or mucous membranes.

Damage to the aluminum laminate sheathing: lithium polymer cells must never be opened, separated, deformed, bent or brought into contact with other packs or soldered. Soldering tags must not be bent, torn or thrown to the ground. This can cause an internal short circuit and an explosion with flame formation. Also, be aware that the electrolyte fluid contained in a LiPo battery is harmful to health.

Usage: Never use a LiPo battery with other batteries. An unwanted discharge can destroy the LiPo cells or the battery used.
!WARNING! Due to the enormous energy density, lithium-polymer cells can ignite or even explode when damaged. This can be caused by extreme overcharging, accidents or mechanical damage, etc.
It is therefore extremely important to monitor the charging process. After an accident, the pack should be checked at the very least. For example, the pack may have been damaged by an accident but will only heat up after half an hour. In case of damage, keep the pack under the most careful observation. The use of a defective battery in an electronic device can cause damage to it.

Case of Fire: If lithium polymer cells catch fire, do not use water as an extinguisher, as this will only foster and aggravate the fire! Please ask your local fire brigade for suitable extinguishing material which should always be within reach (eg dry sand). Also avoid inhalation of the lithium gases, as this can lead to irritation of the mucous membranes, cough, breathing problems, and laryngeal inflammation. These complaints can also occur with a time lag.

Disposal: Batteries contain toxic substances. Therefore, do not throw used lithium polymer cells into the household waste, but dispose of them according to the relevant laws. To avoid accidental short-circuiting, always tape the battery pack with insulating tape.
Lithium cells may only be discharged into the battery collecting receptacles when they are unloaded in the case of trade and public waste disposal vehicles. If the cells are not fully discharged, these must be protected against short circuits as a precaution on the poles with adhesive tape.
Safety when handling lithium-polymer batteries is only guaranteed if the safety instructions described above are followed and the LiPOs are not subjected to any extraordinary stress.
Improper use can destroy the cells or result in personal injury.
We can not be held responsible for any damage to persons, models or cells.

About the technology: Lithium-ion polymer batteries (in short: LiPo) are completely based on Li-Ion technology.
The difference to the Li-Ion battery is in the electrolyte.
It was thickened and combined with a polymer film. Thus, it is no longer liquid or semi-liquid. These characteristics result in an extremely flat battery with a very high energy density of 3.7 V instead of 3.6 V with Li-Ion.

Current rating : This varies depending on the manufacturer between 2C and 90C. Please pay attention to the manufacturer‘s instructions. Please be sure to comply with the legal
requirements for operating drones in your country and make sure that you do not violate any of these requirements.

Charging: The rechargeable battery can be recharged at any time, it does not have a „lazy effect“ and must never be unloaded manually. If the battery is discharged below 3V, it must be charged with 0.1C up to approx. 3 – 3.6V. This ensures a gentle summons. The battery is then charged up to the charging voltage of 4.2 V (exactly: 4.235 V) with 0.5 – 1 C. A charging current of 2C is also possible but can shorten the life of a battery (please note the manufacturer‘s instructions). A must for battery care is LIPOBALANCER. The use of such a device leads to a significantly longer running time of the LiPo batteries. A balancer ensures that no overcharging takes place. For a transfer it may, inter alia, also come when the cells of a pack drift over time, there are various causes for this. Deviations occur, for example, after prolonged storage due to different self-discharges or different charging effects after several charging cycles.

Example: In the normal case, a pack with four parallel and four series- connected cells (4s4p) has a lower voltage than the outer ones, since they become warmer during operation and thus have a higher self-discharge. After a few cycles, the difference is perhaps only 0.02 or 0.05 volts, but after 30 cycles one may already observe differences of 0.2 volts, depending on the cell and discharge depth. If this pack is now charged with a voltage difference of 0.2 Volt, the charger will charge as before also up to 16.8 Volt total voltage. However, this voltage will no longer be evenly distributed among the four groups connected in series. The cells are now loaded, for example, as follows: Group 1 – 4.3 volts, Group 2 + 3 – 3.1 volts, Group 4 – 4.3 volts The cells with 4.3 volts charged cells age very fast, which is not immediately noticeable until the next flight. In the unloading cycle, the individual groups are now unloaded accordingly. While the outer cells are e.g. Still have a charge of 3.6 volts, the inner cells lie at approximately deep discharged 2.4 volts. With a LiPo balancer, this misconduct can be circumvented by balancing the cells of the pack (Lifetime is thereby extended). In addition, the user is informed of the state of each cell during each charging process, as a result of which expensive measurements are omitted.

Warranty

The statutory warranty covers manufacturing and material defects in normal use. We do not accept liability for consequential damages! The guarantee /warranty does not include.

  • Damage caused by failure to observe the safety instructions or the operating instructions
  • Force majeure, boggling, incorrect handling
  • Overuse or foreign influence
  • Unauthorized changes
  • Damage caused by loss of control
  • Influence of current, high voltage, or lightning strike
  • Normal wear and tear
  • Visual defects
  • Transport, shipping, or insurance costs

Care and Maintenance:

  • Although the model is a highly complex system, maintenance is limited to just a few points.
  • After every flight, check the model for visible damage and replace any defective parts immediately. This is especially true for rotating parts.
  • To minimize the wear of moving parts, they must be regularly cleaned and lubricated.
  • Although the bearings are relatively insensitive to soiling, they must nevertheless be regularly checked and, if necessary, cleaned or replaced.
  • Silicone-free silicone oil is recommended for gears and open-running bearings, as is also used for the lubrication of open-running chains. This will dry out after a few minutes, so no dirt or dust can stick to the freshly lubricated components.
  • Before disassembling parts, it is advisable to take one or more photos (also from other viewpoints). This allows you to focus on any problems that may occur.

MSG ONLINE GMBH
Declaration of Conformity in accordance with the Radio Equipment Directive (RED) 2014/53/EU
I hereby declare that the product:
MODSTER FOLD 4K Foldable Drone RTF Modell-Drohne mit Fernsteuerung
Product number: 269631 (EAN: 4260668080950)
Complies with the essential requirements and the other relevant provisions of the Directive (RED) 2014/53/EU, when used for its intended purpose.
Manufactured in accordance with the following harmonized standards:
EN 62479:2010 EN 301 489-1 V2.1.1 (2017-02)
EN 301 489-3 V2.2.1 (2017-03)
EN 62311 Version 2008
EN 300 440 V2.1.1 (2017-03)
EN 62368-1:2014 + A11: 2017
Rechtiche Informationen:
RoHS 2-Richtlinie 2011/65 /EU;
RoHS 3-Richtlinie – Anderung 2011/65 / EU-Anhang II 2015/863
Richtlinie 2012/19/EU Ober Elektro- and Elektronik-Altgerate

sambol 2

MODSTER logo 2

MSG ONLINE GMBH WIRTSCHAFTSPARK 9 A-8530 DEUTSCHLANDSBERG
FIRMENBUCH GRAZ FN315230Z • UID-NR. ATU 64361513
EVA-PARTNERNUMMER: 152216
ARA LIZENZNUMMER: 17749 • GRS NUMMER: 110072576
INTERSEROH HERSTELLER ID (EAR): 152204
WEE REG.-NR. DE 44576630

Documents / Resources

| MODSTER MD10190 Fold 4K Foldable Drone RTF Combo [pdf] User Manual
MD10190, Fold 4K Foldable Drone RTF Combo, MD10190 Fold 4K Foldable Drone RTF Combo
---|---
| MODSTER MD10190 Fold 4K Foldable Drone [pdf] User Manual
MD10190, Fold 4K Foldable Drone, MD10190 Fold 4K Foldable Drone

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals