MUNBYN ITPP068 Direct Thermal Printer User Guide

MUNBYN ITPP068 Direct Thermal Printer

Introduction

• This document describes the setup procedure for the ITPP068. Please read the instructions before using the printer.
• For detailed instructions, please refer to the ITPP068 software manual.

Link:

• Linux Software Manual: http://u.pc.cd/WuuctalK
• MacOS Software Manua1: http://u.pc.cd/zdccta1K
• Windows Software Manual: http://u.pc.cd/Aqk7

Check the Packing List

1. Printer
2. Power Cord
3. USB Cable
4. RS232 Cable
5. Power Adapter
6. Wire Arrangement Cover
7. User Manual
8. Paper Roll Guide
9. Thermal Paper
10. Roller

If there is missing or damage of the packing list,, please contact us via the contact details below

• Email:   support@munbyn.com (24-7 on line support)
• Website: www.munbyn.com (how-to videos)
• WhatsApp: +86 18144898200
• Phone: + l 650 206 2250

Paper Loading

1. Switch the cover opening button and then open the cover.
2. Insert a roll of paper in the direction shown in the illustration.
3. Pull the end of the paper out straight, and push down the printer cover to close

Initial Setup

Set Up The ITPP068 for First Use on Windows

1. Download Windows Driver
2. You can get the driver by clicking the link below to download the driver.
3. Driver download: munbyn.biz/068Wdriver
4. Setting tool download: http://u.pc.cd/eXe
5. USB Interface
6. Connect the printer to the power outlet via the power cord.
7. Connect the printer to your Windows computer via USB.
8. Take the thermal paper into the printer and power it on.

Open the downloaded driver and install it. Demo video: munbyn.biz/068Wvideo

LAN Interface

1. Need to change the printer IP to match your network by ‘Setting Tool’: http://u.pc.cd/eXe
2. For example, if your local network IP address is 772. 78. 788.245, then you need to modify the printer’s IP address to 772.78. 788. 700, the first three positions’ digits must be the same, and the last positions’ digits can be 3~253, but not the same as the local network IP address.

Specific steps are as follows:

1. You need to connect the printer with a Windows computer(We currently only have a Windows version for the setting tool) by USB.
2. Power on the printer and load up the thermal paper.
3. Then, open the “Printer TEST” to start the IP setting, following the instruction below.

Notice:
When you hear a beep from the printer, it means that the IP modification is successful.

• Connect the printer to the router with a network cable. Please see the picture below.
• Open the downloaded driver and install it, then follow the demo video to configure the LAN.
  • Demo video: munbyn.biz/068WLANvideo 

Set Up The ITPP068 for First Use on MacBook

1. Download MacBook Driver
   You can click the link below to download the driver. Driver download: munbyn.biz/068Mdriver

2. USB Interface

3. Connect the printer to the power outlet via the power cord.

4.  Connect the printer to your Windows computer via USB.

5. Place the thermal paper into the printer and power it on.

6. Open the downloaded driver and install it.

7. Demo video: http://u.pc.cd/7Eq7

LAN Interface

• Open the downloaded driver and install it, then follow the demo video to configure the LAN.
• Demo video: munbyn.bi,/068MLANvideo 

Set Up the ITPP068 for First Use on Linux

1. Download Linux Driver
   You can click the link below to download the driver. Driver download link: http://u.pc.cd/WwB7

2. USB Interface

3. Connect the printer to the power outlet via the power cord.

4. Connect the printer to your Windows computer via USB.

5. Place the thermal paper into the printer and power it on.

6. Open the downloaded driver and install it according to the video.

7. Demo video: http://u.pc.cd/sJJ

8. LAN Interface
   Connect your computer to the wireless router. Please see the picture below.

9. Set the IP address of the printer. Open your favorite web browser and navigate to [ http://localhost:637/printers ] to add the printer port according to the video.

10. Demo video: http://u.pc.cd/3xx

Set Up The ITPP068 for First Use Tablet or Phone

LAN Printer Installation

1. Need to change the printer IP to match your network by ‘Setting Tool’: http:/u.pc.cd/eXe
   For example, if your local network IP address is 772.78.788.245, then you need to modify the printer’s IP address to 772.78. 788. 700, the first three positions’ digits must be the same, and the last positions’ digits can be 3~253, but not the same as the local network IP address.
   Specific steps are as follows:

2. You need to connect the printer with a Windows computer(We currently only have a Windows version for the setting tool) by USB.

3. Power on the printer and load up the thermal paper.

4. Then, open the “Printer TEST” to start the IP setting, following the instruction below.

5. Notice: When you hear a beep from the printer, it means that the IP modification is successful.

6. Prepare a router and a network cable, and connect the printer to the router.

7. Use the IP address to connect the printer in the POS App. Take Loyverse App as an example.

8. App LAN Connection demo video: http://u.pc.cd/HpY7

Contact us
MUNBYN provides 18 monthly warranty and lifetime free service. If you encounter any issues with the product, please contact the MUN BYN team to promptly receive troubleshooting tips or a replacement.

• Email:   support@munbyn.com (24-7 on line support)
• Website: www.munbyn.com (how-to videos)
• WhatsApp: +86 18144898200
• Phone: + l 650 206 2250

FCC Statement

• Changes or modifications not expressly a pp roved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Support: +l 650 206 2250

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>