ASTERA AF80 Portable Pluto Fresnel User Manual

ASTERA AF80 Portable Pluto Fresnel

PRODUCT INFORMATION

Contact

• Astera LED Technology GmbH
• Schatzbogen 60
• 81829 Munich
• Germany
• E-mail: info@astera-led.com
• Website: www.astera-led.com

User Manual

• Order Code: AF80
• Manual Version: 1.0
• Date of Issue: 02.05.2023

INTRODUCTION / INTENDED USE

• The PlutoFresnel can be used standing or hanging. For this purpose, the device is equipped with AirlineTracks to attach the appropriate mounting accessories. The PlutoFresnel can be used indoors and outdoors and has an IP55 rating.
• Always fix the fixture with an appropriate safety wire.
• Operate the device only after having become familiarized with its functions. Please consider that unauthorized modifications on the device are not allowed due to safety reasons! If this device is operated in any way different from what is described in this manual, the device may suffer damages and the warranty may be void. The disclaimer includes all damages, liability or injury resulting from failure to follow the instructions in this manual. Furthermore, any other operation may lead to dangers like short circuit, burns, electric shock, crash etc. This device is not for household use and is not suitable for permanent installation.

SAFETY INFORMATION

Before you operate this unit read the manual carefully. Always make sure to include the manual if you pass/rent/sell the unit to another user. Please use your own caution when operating. This product is for professional use only. It is not for household use.

LI-ION Battery

A rechargeable lithium-ion battery is built into this unit.

DISPOSAL

Properly dispose of this product according to local regulations and guidelines for electronic waste disposal.

MANUFACTURER’S DECLARATION

• Hereby, Astera LED Technology GmbH declares that the type of radio equipment PlutoFresnel complies with Directive 2014/53 / EU. The full text of the EU Declaration of Conformity is available at the following Internet address: https://astera-led.com/plutofresnel.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
• FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20 cm from nearby persons.

SECONDARY SAFETY MOUNTING

The PlutoFresnel must always be secured by a safety wire when used in a hanging position. If the primary suspension fails, the device must not fall more than 20cm.

CLEANING AND MAINTAINING

Caution: Liquids entering the housing of the device can cause a short circuit and damage the electronics. Do not use any cleaning agents or solvents. Only clean using a soft damp cloth.

Specifications

• Product Name: PlutoFresnel
• Order Code: AF80
• Fresnel Lens: AF80-FL
• Barndoor: AF80-BD
• Yoke: AF80-YK
• YokeBase: AF80-YKB (x2)
• TVMP Adapter: AX-TVMP
• TrackHandle: AX-THD
• Waterproof Protection Cover : PB15-PLG
• IP Rating: IP55

Product Usage Instructions

Installation

1. Ensure the PlutoFresnel is placed on a stable surface or securely mounted using the provided Yoke and YokeBase.
2. If using the PlutoFresnel in a hanging position, always secure it with a safety wire to prevent falls. The safety wire should be attached to a stable structure.
3. Attach the Fresnel Lens and Barndoor to the front of the PlutoFresnel using the provided accessories.
4. Connect the PlutoFresnel to a power source using the appropriate power cable.

Operating the PlutoFresnel

1. Familiarize yourself with the functions and controls of the PlutoFresnel by referring to the user manual.
2. Ensure that the device is powered off before making any adjustments or changes.
3. Use the provided TrackHandle to adjust the position and angle of the PlutoFresnel as needed.
4. To turn on the PlutoFresnel, locate the power switch or button and press it. The device will illuminate and begin emitting light.
5. Adjust the brightness and focus of the light beam using the controls on the PlutoFresnel.
6. When finished using the PlutoFresnel, turn it off and disconnect it from the power source.

FAQ

• Can the PlutoFresnel be used outdoors?
  Yes, the PlutoFresnel is designed to be used both indoors and outdoors. It has an IP55 rating, which means it is protected against dust and water splashes.

• Is the PlutoFresnel suitable for permanent installation?
  No, the PlutoFresnel is not suitable for permanent installation. It is designed for temporary use and should be securely mounted or placed on a stable surface.

• How should I clean the PlutoFresnel?
  Only clean the PlutoFresnel using a soft damp cloth. Do not use any cleaning agents or solvents, as they can damage the electronics.

• What should I do if I experience interference with the PlutoFresnel?
  If you experience interference with the PlutoFresnel, ensure that it is placed at least 20 cm away from nearby persons. This will help maintain compliance with RF exposure guidelines.

SCOPE OF DELIVERY

• 1 x PlutoFresnel (AF80)
• 1 x Fresnel Lens for PlutoFresnel (AF80-FL)
• 1 x Barndoor for PlutoFresnel (AF80-BD)
• 1 x Yoke for PlutoFresnel (AF80-YK)
• 2 x YokeBase for PlutoFresnel (AF80-YKB)
• 1 x TVMP Adapter (AX-TVMP)
• 1 x TrackHandle (AX-THD)
• 1 x Waterproof Protection Cover (PB15-PLG)
• 1 x User Manual

INTRODUCTION / INTENDED USE

• The PlutoFresnel from ASTERA is a LED Fresnel for professional use in the event and fi lm industry. The PlutoFresnel is designed for direct or indirect illumination of objects and people. Due to its built-in battery it can be quickly set up at places where traditional lights cannot be mounted easily. It has the Titan LED Engine and off ers excellent color and light qualities. The PlutoFresnel generates white or colored light and the color temperature can be adjusted in many ways. It can be controlled with the AsteraApp or with wired DMX or wireless CRMX. The fi xture can also be controlled by the integrated display or by infrared remote control. Thanks to its built-in Bluetooth it can be used as BluetoothBridge (BTB).
• The PlutoFresnel can be used standing or hanging. For this purpose, the device is equiped with AirlineTracks to attach the appropriate mounting accessories. The PlutoFresnel can be used indoors and outdoors and has an IP55 rating.
• Do not shake the device. Avoid brute force when installing or operating the device. When choosing the installation spot, please make sure that the device is not exposed to extreme heat or dust. Avoid direct sunlight for longer periods of time. The specifi ed ambient temperature must be maintained. Keep away from direct insulation (particularly in cars) and heaters. Never use the device during thunderstorms connected to the power mains. Overvoltage could destroy the device. Always disconnect the device during thunderstorms. Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fi xture.
• Always fi x the fi xture with an appropriate safety wire.
• Operate the device only after having become familiarized with its functions. Please consider that unauthorized modifi cations on the device are not allowed due to safety reasons! If this device is operated in any way diff erent from what is described in this manual, the device may suff er damages and the warranty may be void. The disclaimer includes all damages, liability or injury resulting from failure to follow the instructions in this manual. Furthermore, any other operation may lead to dangers like short circuit, burns, electric shock, crash etc. This device is not for household use and is not suitable for permanent installation.

SAFETY INFORMATION

Before you operate this unit read the manual carefully. Always make sure to include the manual if you pass/rent/sell the unit to another user. Please use your own caution when operating. This product is for professional use only. It is not for household use.

• Do not operate the unit in areas of high temperature conditions or under direct sunlight. It can cause abnormal behavior or damage the product.
• Always use a suitable safety wire when mounting the light overhead.
• Connect the safety wire only to the intended safety mount.
• Always follow local safety requirements.

LI- ION Battery: A rechargeable lithium ion battery is built into this unit.

• Only authorized personal may service the battery.

• Do not place in fi re or heat.

• Do not use or charge the light if it is damaged.

• Avoid bumping or plunging, it may cause fi re or explosion.

• Never store the battery when fully drained. Always recharge immediately when empty. Please do not charge unattended.

• Make sure to fully charge all units before storing them.

• Partially charged batteries will lose capacity.

• Fully recharge every 6 months if not used.

• The battery may only be replaced with an original spare part from Astera.

• Follow applicable laws and regulations for transport, shipping, and disposal of batteries. For details on recycling lithium, lithium-phosphate, and lithium-ion batteries, please contact a government recycling agency or your waste-disposal service.

• Always charge with fl ight case open.

• It is recommended to charge at a temperature between 15°C and 35°C.
  Warning: In extreme cases, abuse or misuse of standard/rechargeable batteries can lead to:

• Explosion

• Fire development

• Heat generation or smoke and gas development

• Do not look directly into the light.

• lt can cause harm to your eyes.

• Do not look at the LEDs with a magnifying glass or any other optical instrument that may concentrate the light output.

• Use only Astera approved accessories to diff use or modify the light beam.

• Do not open the product housing.

• Do not apply power if the light is damaged.

• Do not submerge the light into any liquid.

• Do not replace the LED light source.

• Caution, risk of electric shock.
  The PlutoFresnel shall be installed near a socket-outlet which must be easily accessible.
  Warning: risk of electric shock – Do not open device.

• The exterior surfaces of the light can become hot, up to 70°C (158°F) during normal operation.

• Ensure that accidental physical contact with the device is impossible.

• lnstall only in ventilated locations.

• Do not cover the light.

• Allow all lights to cool before touching.

• Keep 0.3 m (12″) from objects to be illuminated.

SECONDARY SAFETY MOUNTING

The PlutoFresnel must always be secured by a safety wire when used in a hanging position. If the primary suspension fails, the device must not fall more than 20cm.

CLEANING AND MAINTAINING

Caution: Liquids entering the housing of the device can cause a short circuit and damage the electronics. Do not use any cleaning agents or solvents. Only clean using a soft damp cloth.

PRODUCT OVERVIEW

Isometric view

Back view

USAGE

Integrated control panel
Use the menu buttons to navigate through the main menu. Settings for color adjustment and brightness / runtime are directly accessible by two symbol buttons.

TouchSlider
The PlutoFresnel has a touch slider. It is only active in certain menus and can also be operated by tapping.

Switching On / Off

• A new PlutoFresnel needs a few seconds of charge to disable its shipping mode before it can be switched on.
• Press the power botton for one second and release it to turn on the PlutoFresnel. When you press the power button to turn on the light, the display will not turn on until you release the button. To turn off the light, press the power button once.

Fan control
The PlutoFresnel has a built-in fan that can be controlled as follows. Navigate to Fan Control menu. There you can choose between the following settings:

• OFF: The fan always remains switched off . If the light becomes too hot, the brightness is gradually reduced. (Ambient temperature dependent)
• AUTO: The fan starts on demand and switches between the three speeds as required. This is the default setting.
• LOW: MED: HIGH: Diff erent speeds. The light never changes them by itself, but if the speed is too low, the brightness is gradually reduced.

More control options

Connect Bluetooth Bridge (BTB)

To control your lights with the AsteraApp, fi rst connect a Bluetooth Bridge (BTB). It forwards the AsteraApp signal to paired lights. You may use an AsteraBox as BTB or choose a light with built-in BTB, like PlutoFresnel, AX9, NYX Bulb, PixelBrick, Titan Tube BTB, Helios Tube BTB.

• Connect AsteraBox as BTB
  Please power on the AsteraBox. Connect the AsteraBox directly from the AsteraApp main menu by following the instructions there.

• Connect light as BTB
  Please note: This ONLY works for Astera lights with built-in Bluetooth. Please power on the light. Hold down the power button for 3 seconds until the light fl ashes blue. In the AsteraApp press „Manage Bluetooth Bridges“, then “+” and follow instructions on screen to connect. The light which is connected as BTB shows a small Bluetooth icon in the display.

Pair with lights

• Once the AsteraApp is connected to a BluetoothBridge, you can pair your lights with the app:
• Please power on the light(s). Then hold down the power button for 3 seconds until the lights fl ash blue. Go to “Pair with Lights” dialog in the AsteraApp. Then press OK.

Linking to a CRMX transmitter

The PlutoFresnel can be controlled via Wireless DMX/ CRMX. To do this, it must fi rst be connected to a CRMX transmitter. There are two diff erent methods to do this: either the connection is established by pressing a button on the transmitter or a linking key is set that matches the transmitter.

• **Linking via push button

**

• Linking via linking key
  Alternatively, PlutoFresnel can also be connected to a CRMX transmitter using a linking key, provided that the transmitter supports this linking option. To set a linking key, navigate in the main menu to „DMX SETTINGS“. Under „CRMX LINK BY KEY“ you can enter the desired eight-digit combination.

Reset
RESET sets „Input Select“ to „AUTO“ and runtime to 5 h.

Charging
While the power cable is connected, the display shows the charging status. Charge immediately when the battery is empty. Do not store the unit when the battery is empty.

Rigging

• The PlutoFresnel is equipped with AirlineTracks on all four sides to attach various Astera mounting accessories. When installing accessories on the airline tracks, they must audibly click into place!

• With the included multifunctional yoke, PlutoFresnel can be easily hung or placed on the fl oor. When hanging, always secure with a safety wire at the safety eyelet on top of the light’s housing. Make sure the light cannot drop more than 20cm if primary mounting fails.
• The PlutoFresnel can also be mounted on tripods. For this purpose, a TVMP (TV to motion picture) adapter that can be attached to the yoke of the PlutoFresnel is included with the product.

Yoke attachment with YokeBase – Quick Release

• To attach the PlutoFresnel yoke, the two YokeBases must fi rst be inserted into the AirlineTracks on opposite sides. To secure the YokeBase, turn the BaseLock clockwise.

• The scales in the AirlineTracks help to ensure that the same position is selected on both sides. There is a default position for the YokeBase.

• You can move the YokeBase to balance the light or to use it in a diff erent confi guration. It is important that the YokeBase is oriented so that the opening of the V points downward. When the light is properly prepared, the yoke can be inserted into the YokeBases from the bottom up.

• The yoke is attached to the YokeBases with a Quick Release system. To release the yoke, fi rst loosen the Tilt Lock. This acts as a safety for the Quick Release. Once the Tilt Lock is loose, press the QuickRelease buttons on each YokeBase to release the fi xture from the Yoke. Make sure to hold the fi xture securely while releasing it.
  Attention: Only unscrew YokeBase if yoke is detached!

Yoke as Floorstand
The PlutoFresnel yoke can be used to fl oor mount the light. To do this, the two legs are folded out.

Mounting options with Yoke

• The PlutoFresnel Yoke has a mounting hole allowing for the use of up to 1/2″ or M12 bolt, as well as being able to be converted to a 3/8″ thread to attach spigots or bolts to the yoke. The 3/8″ thread adapter is mounted to the inside of the yoke and swings in place. There is also an AirlineTrack for use with TrackPin and similar.

• On the left outside is a BrickMount (PB15-BMO), to which suitable Astera accessories, such as a RuntimeExtender can be attached.

TVMP Adapter

• The TVMP adapter has a 1/2″ thread on top and comes with a 1/2″ bolt with washer. With this bolt the TVMP adapter can be attached to the hole of the PlutoFresnel yoke.

• This allows the PlutoFresnel to be mounted on stands using the BabyPin (5/8″) receiver or the JuniorPin (1-1/8″).

• In this application, the TVMP T-Bolt can be stowed on a dedicated thread on the yoke to prevent it from being lost.

TrackHandle

• The included TrackHandle easily converts the PlutoFresnel into a handheld light. To do this, simply attach the TrackHandle with its robust double stud fi tting to one of the PlutoFresnel’s AirlineTracks.

• The TrackHandle is also a useful accessory for general handling of the light.

Beam modifi ers

• PlutoFresnel can not only be used as Fresnel but also be used as an open face light without any beam modifi ers.
• In addition to the Fresnel lens, Barndoors are included in the product scope.

Fresnel Lens

• With the included Fresnel lens PlutoFresnel provides a beam from 15° to 60°.

• To insert the Fresnel lens, pull the barndoor lock upwards and turn it to the side. Now slide the Fresnel lens into the holder provided and close the barndoor lock by lifting and turning it again. Make sure that the barndoor lock is properly engaged before moving the light.

Barndoor
8 leaf barndoor is included as standard. They are inserted in front of the Fresnel lens in the same way as the Fresnel lens.

Zoom
The built-in zoom allows adjustment of the beam between 15° and 60°. There is a scale on the side of the lens tube for reference.

TROUBLESHOOTING

SPECIFICATIONS – TECHNICAL DATA

• Order Code AF80
• LED Engine Titan LED Engine
• Colors RGBMintAmber
• Total LED Power 105W
• LED Power Draw 80W
• CRI (Ra)/ TLCI 3200- 6500 K* ≥96
• Beam Angle 15° – 60°
• Strobe 0 – 25 Hertz
• Pixels 1
• Battery Runtime up to 20 hours
• Battery Runtime max. Brightness 3h
• Battery Lifetime 80 % after 400 cycles
• DC Input 24 VDC, 80W
• DC Connector 5.5 mm x 2.1 mm
• Power Consumption (max.) 80W
• Wired DMX via PWB -2-86W
• CRMX Receiver Built-in
• BluetoothBridge BTB Built-in
• Wireless Protocols CRMX, UHF, Bluetooth, WiFi, RDM
• Wireless Range
  • CRMX/UHF up to 300 m / 330 yds
  • Bluetooth up to 3 m / 3.3 yds
• Infrared Control Yes
• TouchSlider Yes
• Housing Material Polymer & Metal
• IP Rating unwired IP55
• IP Rating wired IP55
• Ambient Operating Temperature 0 – 40 °C / 32 – 104 °F
• Weight (with AF80-FL, AF80-BD) tbd
• Weight (with AF80-FL, AF80-BD, AF80-YK, 2x AF80- YKB) tbd
• Dimensions L x W x H 281.9 mm x 153.5 mm x 161.8 mm / 11.1″ x 6.0″ x 6.4″
• Dimensions L x W x H (AF80-YK, 2x AF80-YKB) 281.9 mm x 244.7 mm x 323 mm / 11.1″ x 9.6″ x 12.7″

DISPOSAL

• The light contains a lithium ion battery.
• Don‘t throw the unit into the garbage at the end of its lifetime.
• Make sure to dispose of according to your local ordinances and/or regulations, to avoid polluting the environment!
• The packaging is recyclable and can be disposed.

MANUFACTURERS DECLARATION

• Hereby, Astera LED Technology GmbH declares that the type of radio equipment PlutoFresnel complies with Directive 2014/53 / EU. The full text of the EU Declaration of Conformity is available at the following Internet address: https://astera-led.com/ plutofresnel.
• Astera LED Technology GmbH declares that this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

• Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.
• FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20 cm from nearby persons

ABOUT COMPANY

• Astera LED Technology GmbH
• Schatzbogen 60
• 81829 Munich
• Germany
• E-mail: info@astera-led.com
• Website: www.astera-led.com

References

• LED Commercial Lighting and Lighting Controls | Current - GLI Brands
• Wireless LED Lighting Film & Event by Astera
• Wireless LED Lighting Film & Event by Astera

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>