DieseRC 2201H Universal Wireless Remote Control Switch Instruction Manual
- June 15, 2024
- DieseRC
Table of Contents
PRODUCT MANUAL
RELAY REMOTE CONTROL SWITCH
PRODUCT INFORMATION
TYPE—-2201H
| Working voltage | Technical Data |
|---|---|
| Input/output vlotage | AC 85V~250V |
| Output Type | AC 85V~250V |
| Quiescent Current | Active output |
| Max current | <5MA |
| RF frequency | 30A |
| Working temperature | 433MHz |
| Receiving Sensitivity | -30~+80 |
| Amount of storage | >97dbm |
| remote controls | 20 pieces |
| Support encoding | 1527 Leaning code、2262 fixed code |
| RF Ovperating mode | ASK superheterodyne wireless reception |
| Receiving range | Open space is more than 50 meters |
| Remote operating mode | Momentary Mode /Toggle Mode /Latched Mode |
PRODUCT DETAIL
WIRING DIAGRAM
| 
---|---
Warning
-
Usually the receiver and transmitter have been paired with each other in factory.
If not, please reprogram them. -
Reset before you want to change the operating mode.
-
After reset, all the remote controls cannot work anymore.
-
Replace the battery in time when the remote transmitter voltage is low. To get the stronger signal transmission.
-
Slightly stretch the antenna on the receiver for better signal reception.
-
The remote transmitter need to have 2 or more buttons, if you want to set up in latched mode.
Operating Mode
Momentary Mode:
- Press and hold the button, relay will turn on;
- Release the button, this relay will turn off.
How to program
- Press the learning button (on the receiver) 1 time. The indicator LED on the receiver will light up;
- Press one button on the remote transmitter. The indicator LED on the receiver will flashing several times and then light down. Succeed.
Toggle Mode:
- Press button “A”, relay will turn on;
- Press button “A” again, this relay will turn off.
How to program
- Press the learning button (on the receiver) 2 times. The indicator LED on the receiver will light up;
- Press one button on the remote transmitter. The indicator LED on the receiver will flashing several times and then light down. Succeed.
Latched mode:
- Press button “A”, relay will turn on;
- Press button “B”, this relay will turn off.
How to program
- Press the learning button (on the receiver) 3 times. The indicator LED on the receiver will light up;
- Press button “A” on the remote transmitter. The indicator LED on the receiver will flashing several times and then light up;
- Press button “B” on the remote transmitter. The indicator LED on the receiver will light down. Succeed.
Reset
Press the learning button (on the receiver) 8 times. The indicator LED on the
receiver will flashing several times and then light down. succeed.
Troubleshooting
If the receiver and transmitter cannot operate normally, try to solve the problem by follow the step below.
- Please check if batteries power is used up. The indicator LED on remote transmitter does not light up or is dimly lit.
- Please check if your receiver is wired correctly. It is important to make sure the wiring is correct.
- Reprogram the receiver and transmitter. Usually this can solve a lot of problem.
- If the problem still remains, please contact us in time. We will do our best to solve your problem. Email: “ dieseelectronic@163.com ” or WhatsApp: +86 13502278583
CUSTOMER SERVICE
Work volts: AC 85V~250V
Max current:30Amp
If there is any questions about the products,please contact us firstly. We will do our best to solve your problem. Thank you.
Huizhou Wenqiao
Electronic Technology Co., Ltd.
Address: 1203, Building T19, Fangzhilonghuwan, Sanhuan South Road,
Huicheng District, Huizhou City, Guangdong Province, China 516000
WhatsApp : +86 13502278583 / +86 18138805271
Email :dieseelectronic@163.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>