DieseRC 2202G RF Relay Remote Control Switch User Manual
- June 12, 2024
- DieseRC
Table of Contents
DieseRC 2202G RF Relay Remote Control Switch
Product Information
- Type: 2202G
- Working voltage: AC 90V~250V 50/60Hz
- Input/output voltage: 1~250V
- Output Type: Passive
- Quiescent Current: 97dbm
- Max current: N/A
- RF frequency: N/A
- Working temperature: N/A
- Receiving Sensitivity: N/A
- Amount of storage remote controls: 20 pieces
- Support encoding: 1527 Leaning code
- RF Operating mode: ASK superheterodyne wireless reception
- Receiving range: Open space is more than 50 meters
Product Usage Instructions
Momentary Mode:
- Press and hold button A to turn on relay 1.
- Release button A to turn off relay 1.
Programming:
- Press the learning button on the receiver once. The indicator LED on the receiver will light down.
- Press button A on the remote transmitter. The indicator LED on the receiver will flash several times and then light down.
- Press button B on the remote transmitter. The indicator LED on the receiver will flash several times and then light up. Programming is successful.
Toggle Mode:
- Press button A to turn on relay 1.
- Press button A again to turn off relay 1.
Programming:
- Press the learning button on the receiver twice. The indicator LED on the receiver will light down.
- Press button A on the remote transmitter. The indicator LED on the receiver will flash several times and then light down.
- Press button B on the remote transmitter. The indicator LED on the receiver will flash several times and then light up. Programming is successful.
Latched Mode:
- Press button A to turn on relay 1.
- Press button B to turn on relay 2 and turn off relay 1 simultaneously.
Programming:
- Press the learning button on the receiver three times. The indicator LED on the receiver will light down.
- Press button A on the remote transmitter. The indicator LED on the receiver will flash several times and then light down.
- Press button B on the remote transmitter. The indicator LED on the receiver will flash several times and then light up. Programming is successful.
Reset:
Press the learning button on the receiver eight times. The indicator LED on
the receiver will flash several times and then light up. Reset is successful.
Troubleshooting:
If the receiver and transmitter cannot operate normally, try to solve the
problem by following these steps:
-
Check if the batteries in the remote transmitter are used up.
The indicator LED on the remote transmitter does not light up or is dimly lit. -
Check if the receiver is wired correctly. Ensure the wiring is correct.
-
Reprogram the receiver and transmitter. This can often solve many problems.
-
If the problem still persists, please contact us for assistance. Email: dieseelectronic@163.com or WhatsApp: +86 13502278583
PRODUCT INFORMATION
TYPE: 2202G
Technical Data
Working voltage| AC 90V~250V 50/60Hz
Input/output vlotage| 1~250V
Output Type| Passive output
Quiescent Current| <5MA
Max current| 10A
RF frequency| 433MHz
Working temperature| -30~+80
Receiving Sensitivity| >97dbm
Amount of storage remote controls| 20 pieces
Support encoding| 1527 Leaning code
RF Ovperating mode| ASK superheterodyne wireless reception
Receiving range| Open space is more than 50 meters
Remote operating mode| Momentary Mode /Toggle Mode /Latched Mode
PRODUCT DETAIL
- NO: Normally open pin
- COM: Common pin
- NC: Normally closed pin
WIRING DIAGRAM
Warning
- Usually, the receiver and transmitter have been paired with each other If not, you can reprogram by yourself.
- Reset before you want to change the operating
- After reset, all the remote controls cannot work
- Replace the battery in time when the remote transmitter voltage is To get a stronger signal transmission.
- Slightly stretch the antenna on the receiver for better signal
- The remote transmitter needs to have 3 or more buttons, if you want to set it up in latched
- The output type is passive output / potential-free
Operating Mode
Momentary Mode:
- Press and hold on button “A”, relay “1” will turn on;
- Release the button “A”, this relay “1” will turn How to program
- Press the learning button (on the receiver) 1 The indicator LED on the receiver will light down;
- Press button “A” on the remote The indicator LED on the receiver will flash several times and then light down;
- Press button “B” on the remote The indicator LED on the receiver will flash several times and then light up. Succeed.
Toggle Mode:
- Press button “A”, relay “1” will turn on;
- Press button “A” again, this relay “1” will turn How to program
- Press the learning button (on the receiver) 2 times. The indicator LED on the receiver will light down;
- Press button “A” on the remote The indicator LED on the receiver will flash several times and then light down;
- Press button “B” on the remote transmitter. The indicator LED on the receiver will flash several times and then light up. Succeed.
Latched mode:
- Press button “A”, relay “1” will turn on;
- Press button “B”, and relay “2” will turn on, and at the same time relay “1” will turn How to program
- Press the learning button (on the receiver) 3 times. The indicator LED on the receiver will light down;
- Press button “A” on the remote The indicator LED on the receiver will flash several times and then light down;
- Press button “B” on the remote The indicator LED on the receiver will flash several times and then light up. Succeed.
Reset
- Press the learning button (on the receiver) 8 times. The indicator LED on the receiver will flash several times and then light up. Succeed.
Troubleshooting
If the receiver and transmitter cannot operate normally, try to solve the problem by following the steps below.
- Please check if battery power is used The indicator LED on the remote transmitter does not light up or is dimly lit.
- Please check if your receiver is wired It is important to make sure the wiring is correct.
- Reprogram the receiver and Usually, this can solve a lot of problems.
- If the problem remains, please contact us We will do our best to solve your problem. Email: “dieseelectronic@163.com” or WhatsApp: +86 13502278583
CUSTOMER SERVICE
Work volts: AC 90V~250V Max current If there are any questions about the
products, please contact us first. We will do our best to solve your problem.
Thank you
Huizhou Wenqiao Electronic Technology Co., Ltd. Address: 1203, Building T19,
Fangzhilonghuwan, Sanhuan South Road, Huicheng District, Huizhou City,
Guangdong Province, China 516000 WhatsApp : +86 13502278583 / +86 18138805271
Email : dieseelectronic@163.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>