WP280013267 Winees Spotlight Camera Instruction Manual

WP280013267 Winees Spotlight Camera Instruction Manual

PRODUCT USING INSTRUCTION

To avoid personal injury and/or possible product damage, the following cautions must be followed:

1. Please use sorely the provided adapter instead of others in case of any damage to the product.
2. Keep out of reach of children. This product contains small magnets and other small parts, which can cause choking or injury if ingested.
3. To prevent early failure,the camera should only be installed in operating environments ranging between
   • 20°C ~ 50°C(-4°F ~ 122°F).
4. Do not install
   • close to heat source
   • near the metal objects and mirrors that cause radio signal attenuation or shading.
5. Do not disassemble or reinstall the camera, otherwise it may cause security risks.
6.  Unplug the power cord before cleaning. Do not clean the camera with any liquids, spray cleaner or wet cloth.
7. The slot and opening are used for ventilation, not allowed to be blocked or covered.

Introduction

Package Contents

• Winees spotlight cam *1

• AC adapter *1

• Screw2, wall anchor2

• Reset pin *1

Status LED Description

Set up Spotlight Cam in the AiDot App

1. Scan the QR code below
   
   Or search for“ Ai Dot” in App Store or Google Play
   

2. Power on the camera, you will hear “Waiting for Wi-Fi configuration” with the camera’s indicator light flashing in green.
   

3. In the AiDot app, press ‘+’ – “devices”, select Winees Spotlight Cam, and follow the instructions on App.
   

4. Place the spotlight cam in the area where you plan to install to test the video quality, ensure that the camera can work normally after the final installation.

Install Spotlight Cam on the wall or celling

1. Placement
   The recommended installation height is 2.5~3 meters (8.2~9 feet) above the ground. Either too high or too low height may affect the operation of the motion detector.
   
   Motion detect area

2. Install the bracket
   When install the bracket on the wall/ceiling, please pay attention to the installation direction of the base.
   If installing on a masonry surface, drill holes on the wall first, insert the anchor into the hole, and then install screw to fix the base.
   If installing on a wooden surface, install screw to fix the base directly.
   Note: When install it upside down on the ceiling, you’ll need to set the image angle to 180° in the camera settings after adding the camera on the app.
   
   On the wall
   
   Ceiling
   
   On a masonry surface
   
   On a wooden surface

3. Tighten the camera.
   Arrange the cables behind the camera. You can route the wire from the top or bottom. Align the arrow on the camera base with that on the mounting bracket, snap it into place with a clear ”click” sound, and then tighten it with the Security Screw.
   

4. Adjust the camera angle
   Manually adjust the up and down angle of the camera to obtain an accurate monitoring image and motion detect range. The tightness of the up and down rotation can be adjusted by the screw at the connection.
   

5. Power on the camera
   Power on the camera and wait for the camera to work.
   

Requirements and Tech Specs

Wi-Fi Network Requirements

• Supports IEEE 802.11b/g/n
• Your Wi-Fi network broadcasts at 2.4GHz. 5GHz band is not supported
• Your network upload speed is suggested to be greater than 1
  Mbps to
  have fluent video streaming.

Power (Only for CE)

• 100~ 240VAC 50/60Hz power supply for the AC adapter
• DC 12V/1A input for the camera
• Max. power consumption: 10W
• Frequency range : 2412-2472MHz
• Maximum RF transmit power: 802.11b 16±2dBm, 802.11g 54M 14±2dBm, 802.11n HT20 12±2dBm, 802.11n HT40 12±2dBm
  Maximum radio-frequency power: 20 dBm

Camera

• 2K QHD @25 frames per second
• Maximum resolution: 2560*1440
• 1/3” Color CMOS sensor
• 135° (diagonal) wide angle lens
• Video compression: H.265/H.264
• Infra-red night vision: 10m(32.8ft)
• Motion detection: 7m Max.
• Rotation: 270° pan

Audio

• Built-in microphone and speaker
• Two-way talk

Lighting

• White light LED: 5000K, 400lm

Siren

• 100dB @10cm Max

Storage

• Micro SD card storage up to 128 GB (Micro SD card is not included)

Operating Environment

• Temperature: -20°C ~ 50°C(-4°F ~ 122°F)
• Humidity: ≤95% non-condensing

Trouble Shooting

If the default adding camera operation fails

• Make sure your wireless router has the Internet access, and the Wi-Fi signal at the location where you install the camera is good.

• Make sure the camera is plugged in and the status LED is on or flashing

• Reset the camera if the LED is NOT flashing green. Then follow the App to add it.

• Make sure the camera is not added to other user’s account. If it is, the owner of the camera has to unbind it first.

• When this step is done, the camera should be added to your account.
  If the Micro SD card is not detected by the camera

•  Make sure the card is good and format it again in the FAT-32 format. How to do the forced reset?

• If you cannot reset the camera from the setting page, please hold the reset button in the pin hole with the reset pin for 3 seconds and release. The camera will play a voice prompt” Restoring factory settings”.

The time of the camera video stamp is not right

• Please set the right time zone in the settings.

How long can a Micro SD card (not included) of different capacity record?

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

FCC Statement

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

Business name: APEX CE SPECIALISTS LIMITED
Business address: 89 Princess Street,
Manchester, M1 4HT, UK
Email: info@apex-ce.com
Tel: +441616371080

Business name: APEX CE SPECIALISTS LIMITED
Business address: UNIT 3D NORTH POINT HOUSE,
NORTH POINT BUSINESS PARK, NEW MALLOW ROAD,
CORK, T23 AT2P, IRELAND
Email: info@apex-ce.com
Tel: +353212066339
Contact Us / Kontaktieren Sie uns

Linkzone Technology Co., Limited
ROOM 20 5/F WAYSON COMMERCIAL BLDG 28 CONNAUGHT ROAD WEST SHEUNG WAN HK
Phone: 1-855-334-9800
Website: www.iwinees.com
Email: support@iwinees.com

Made in China

Documents / Resources

| Winees WP280013267 Winees Spotlight Camera [pdf] Instruction Manual
WP280013267 Winees Spotlight Camera, WP280013267, Winees Spotlight Camera, Spotlight Camera, Camera
---|---

References

• ce.com
• Winees Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>