Monoprice SSVC-4.1 Single Input 4-Channel Speaker Selector with Volume Control User manual
- June 4, 2024
- Monoprice
Table of Contents
**
**
**Monoprice SSVC-4.1 Single Input 4-Channel Speaker Selector with Volume
Control
**
Specification
- DIMENSIONS: 5 x 9 x 3.4 inches
- WEIGHT: 94 ounces
- CHANNELS: 4
- PEAK POWER: 200 watts
- CONTINUOUS POWER: 100 watts
The SSVC-4.1 Speaker Selector is a resistor-based, impedance-matching speaker selector used for connecting up to four pairs of 4-ohm or 8-ohm speakers while maintaining a safe impedance load for your amplifier or receiver. Each pair of speakers can be independently turned on or off using push buttons on the front panel, with no need for worrying about amplifier loading. Each zone features independent volume control.
FEATURES
- Connect and safely control multiple speaker pairs with a single amplifier
- Automatic impedance protection circuitry
- 100 watts/channel continuous power handling capacity, 200 watts/channel peak
- 5-ohm minimum amplifier impedance with four 4-ohm speakers selected, 6-ohm minimum with 8-ohm speakers
- Individual zone on/off buttons and volume controls
- Heavy-duty screw-type connectors supporting 12-18 AWG speaker wire
- Isolated left/right circuit grounds provide safe connection for amplifiers with floating grounds or bridged configurations
- Accurate, noise-free switching
INSTALLATION
- Refer to the manuals for your amplifier and speakers to determine the correct wire gauge to use with the speaker selector.
- Lay out all wire runs from each speaker location and your amplifier to the selector.
- Remove the connector blocks from the selector and connect them to the wires, as shown in the image to the right.
Carefully inspect the connections for any stray wire strands.
- Insert the connector blocks back into the selector.
- Connect the other ends of each zone wire to the speakers and the input wires amplifier. If your amplifier has A and B outputs, use the A output.
SETTING THE VOLUME CONTROLS
Perform the following steps to configure the volume controls to avoid distortion.
- Set the amplifier’s volume control to the minimum position.
- Enable each zone and turn each volume control on the selector to the maximum position.
- While playing audio material, slowly increase the volume on the amplifier until the best maximum volume with no distortion is achieved.
Turn down the volume of each zone until it is at a comfortable listening level. By attenuating a previously determined maximum volume level, maximum volume can be used without fear of causing distortion.
FREQUENTLY ASKED QUESTIONS
What does l- l+ r- r+ mean?****
L and R stand for the left and right speakers, respectively.
What are the actual dimensions of the unit?****
12″ x 6.25″ (excluding knobs which are ~.75″) x 2″
Can I connect 2 pairs of 8 ohm (1 pair rated at 6 ohms nominal), to this Monoprice unit to 1 Amp and play them simultaneously?****
No, it can’t.
Can you have two or more zones on at the same time? Or, just one zone at a time?****
All zones can work at the same time.
Is the impedance matching performed by resistors or transformers?****
Up to four pairs of 4-ohm or 8-ohm speakers can be connected using the SSVC-4.1 Speaker Selector, which uses resistors to match impedance and maintain a safe impedance load for your amplifier or receiver.
Can I have two volume controls on one speaker?****
No, you can’t.
Does it have a remote?****
It doesn’t have a remote.
What is the input type for plug for speaker?****
Euroblocks, often known as speaker terminal blocks (those green blocks on the back that you can remove and reinsert with the cables secured in them). Amazing results using cables of standard gauge.
Could all zones be listened to simultaneously?****
Yes, all zones can be used simultaneously.
How do I set up a speaker selector?****
Speaker selectors are simple devices with few moving parts. The speaker output terminals from your receiver (often Zone 2 or assignable back channels) or amplifier are simply connected to the speaker selector, as shown in the image below. Then, you attach each set of speakers to the speaker selector’s back.
What is a speaker selector?****
You can quickly control the level of your speakers with the help of the speaker selector with volume. For people who enjoy listening to music in their living rooms or bedrooms, it is a fantastic tool. View the top-ranked list of speaker selections for volume and related reviews and ratings below.
How do impedance matching volume controls work?****
Enables the use of numerous speaker pairs in conjunction with an amplifier. Up to eight pairs of 8-ohm speakers can be driven by a single 8-ohm capable amplifier thanks to adjustable impedance jumpers. 12 control settings, soft- touch action, and silent switching capabilities are included.
Does a speaker switch affect sound quality?****
As a general rule, stay away from budget switchers with volume controls. They’ll have an impact on audio quality.
How many channel amps do I need for 4 speakers?****
A four-channel amp may supply four speakers, two speakers, and a subwoofer by bridging two of the channels together to power the sub. It can also power four speakers, two speakers, and two rear full-range speakers.
Can I connect multiple speakers to 1 output?****
The only actual options for connecting two speakers to a single amplifier are parallel and series connections. You can typically connect speakers in parallel if they have an impedance of 8 ohms or higher. Wire your speakers in series if their combined impedance is less than 8 ohms.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>