MONOPRICE 39655 Menu Board Ceiling TV Mount for Screens Instruction Manual

MONOPRICE 39655 Menu Board Ceiling TV Mount for Screens

SAFETY GUIDELINES

• Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.
• Do not exceed the rated weight limit. Doing so can cause the mount to fail, resulting in equipment damage and/or severe personal injury.
• Ensure that the structure to which this mount will be installed is capable of supporting at least four times the total weight of the mount and any connected displays.
• Use the supplied mounting screws. Tighten the screws using the appropriate tool, but take care not too over-tighten them.
• This device is intended for indoor use only.
• This device contains small parts that could pose a choking hazard to small children. Keep this device and its spare parts out of reach of children.
• Inspect the installation at least once every three months to ensure that it is secure and safe to use.
• Please take an inventory of the package contents to ensure you have all the items shown in the Parts List. If anything is missing or damaged, please contact Monoprice
• Customer Service for a replacement.
• Make sure that mounting screws are abchored into the center of joists/studs. The use of a stud finder is highly recomended.
• Always attach concrete anchors directly to load-bearing concrete.
• Never attach concrete anchors to concrete-covered plaster, drywal, or other finishing material. If mounting to covered concrete surfaces is unavoidable, the finishing surface must be counterbored described in this manual. Be sure concrete anchors do not pull away from concrete when the screws are tightened.

CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links

Install to Solid Wood Ceiling

WARNING

• Tighten wood screws so that ceiling plate is firmlyattached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Make sure that mounting screws are anchored into thecenter of the joist. The use of an “edge to edge” stud finder is highly recommended.

Install to Concrete Ceiling

WARNING

• When installing the wall mount to cinder block, verify that you have a minimum of 1-3/10″ of actual solid concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1 minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
  It is recommended that a standard electric drill set on a slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must have a 2000 psi density minimum. Lighter-density concrete may not hold the concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

A Drill four 3/10″(8 mm) dia. holes 2.2″ (56 mm) deep.
Use wall bracket of (AA) as template to mark mounting holes Insert concrete anchor (H) in holes flush with the wall as shown (right). Place wall plate over anchors and secure with M6x 50 screws (G) and Washer (G). Level, then tighten all fasteners.

WARNING
Always attach concrete anchors directly to loadbearing concrete.
Never attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tighten- ing screws. lf plaster/drywall is thicker than 5/8, custom fasteners must be supplied by the installer.

CUTAWAY VIEW

Installation& Adjustment of the screen

1. Start by pulling the arm up to 90 degrees

2. Insert two of the Phillips pan head screw into the TV. The crew will vary based on the TV’s requirement. The spacer L(E) can be used for recessed mounting.

3. Sliding the TV into two slots in the bracket.

4. Secure the display with the same screws previously used in Step 2.
   Adjust positioning of the ceiling mount to a suitable force with the allen wrench (F).

5. Adjusting the TV to the desired position and locking it with the allen wrenchs(F).

PRODUCT DIMENSIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>