regalo 2020 Swing Down Bed Rail Guard User Manual

: June 15, 2024
: regalo

Table of Contents

regalo 2020 Swing Down Bed Rail Guard
Specifications
Product Usage Instructions
Before Assembly
CARE AND MAINTENANCE
Assembling Your Bed Rail
Installing Your Bed Rail
Operating the Swing Down Feature
Replacement Parts
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

regalo 2020 Swing Down Bed Rail Guard

regalo-2020-Swing-Down-Bed-Rail-Guard-product

Specifications

Mesh Wall Material: Mesh fabric
Support Bar Material: Metal
Hinge Assembly Material: Plastic

Product Usage Instructions

Before Assembly
Before starting the assembly process, please ensure that you have all the required parts:

Mesh Wall (A)
Bottom Support Bar B (E)
Upper Support Bar B (C)
Hinge Assembly A (F)
Upper Support Bar C (C)
Hinge Assembly B (L)
Bottom Support Bar A (D)

Warning

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF BED RAIL.
KEEP INSTRUCTIONS FOR FUTURE USE.
LIRE TOUTES LES INSTRUCTIONS AVANT D’ASSEMBLER ET D’UTILISER LIT RABATTABLE. CONSERVER CES INSTRUCTIONS POUR UNE UTILISATION ULTÉRIEURE.
LEA TODAS LAS INSTRUCCIONES ANTES DE MONTAR Y USAR BARANDILLA ABATIBLE. GUÁRDELAS PARA UTILIZARLAS COMO REFERENCIA.

Before Assembly

PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:

A: Mesh Wall
B : Upper Support Bar
C : Upper Support Bar
D: Bottom Support Bar A
E: Bottom Support Bar B
F: Hinge Assembly A
G: Hinge Assembly B

BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your product is properly installed. Failure to follow these instructions for the assembly of use of your bed rail could result in serious injury or death. The safety of your child is your responsibility. Please keep these instructions for your reference.

IMPORTANT: Do not use two separate bed rails on one bed. The bed rails will not function properly and could be a safety hazard. Should you need coverage on both sides of the bed, purchase the Regalo Double Sided Bed Rail.

CARE AND MAINTENANCE

Periodically check the bed rail for signs of damage, wear or for missing components. Do not use if any part is missing, worn or damaged. Check the bed rail regularly to make sure all hardware and mountings are tight and secure. Do not use abrasive cleaners or bleach when cleaning. Proper cleaning of bed rail can be done by sponging it with warm water and mild detergent. Do not machine wash.

Assembling Your Bed Rail

Insert the upper support bar (C) into the bottom support bar (E). Make sure the spring pin ﬁts securely into the opposing hole so that the two pieces cannot pull apart. Repeat on the opposite side (B, D) of the bed rail.
With the upper and bottom support bars assembled, connect the two sides.
NOTE: Make sure that the spring pins are secured into the opposing holes so that the bed rail cannot pull apart.
To install the mesh wall (A) on the bed rail, slide it over the frame until it reaches the other end, zip it shut, then attach the velcro strap over the zipper to complete the installation. Mesh wall must go over entire bed rail frame.
With the wall of the bed rail completely assembled, you will now connect the hinge assemblies (F, G).
Insert one side of the wall frame with locating pin into the hinge assembly labeled “B”. Press in the metal spring button to fully insert the tube into the hole in the plastic hinge. The spring button should line up with the access hole in the plastic sleeve on the hinge. The spring button will rebound and lock the tube in place. Repeat on opposite hinge assembly “A”.

NOTE: If the zipper does not close securely, make the necessary adjustments to ensure proper closure. DO NOT use the bed rail without securely zipping the mesh wall properly.

Installing Your Bed Rail

Start by placing the bed rail on the side of the bed you have chosen for installation. The left and right swing lock and strap assemblies should be placed on top of the box spring that will support the mattress. The ‘T’ shaped anchors and straps should be extended opposite the bed rail and mounted to the outer edge of the box spring or mattress support structure.
Once the bed rail is properly placed, check to make sure the left and right swing lock and strap assemblies are parallel to one another. Then, place the mattress on top of the assembly.
NOTE: In order for the bed rail mesh wall to be ﬁrmly held against the side of the mattress you MUST properly tighten the anchoring straps. Please follow the next STEPS 3 – 4 carefully.
NOTE: You may need to release the strap locking buckles located on the under side of the plastic hinges. Ensure that the large end of the anchor is pointing up. The anchoring straps should not be twisted. If twisted, the anchoring straps will not tighten properly.
Tighten the straps to bring the bed rail into its proper position. To tighten the straps, first release the strap locks on the under side of the left and right under bars. Pull the straps towards you until all the excess slack has been pulled out from under the mattress
If the strap does not pull through smoothly, the strap may be twisted under the mattress. Correct this before continuing with the installation. Once you have taken the slack out of the straps, give one ﬁnal pull on the strap end, hold it, and push down on the locking buckle to secure the strap tension. Use the same procedure for each side to properly secure the bed rail
NOTE: When using this bed rail on a foam mattress with little or no internal structure, make sure not to over tighten the mounting straps. If over-tightened, the mattress will likely fold or buckle in the middle and this will cause the bed rail to not provide your child with the highest level of safety. Make slight adjustments to ﬁnd the best level of tightness on your mattress. The bed rail must be tight but should not buckle or fold.
With your bed rail in the ‘up’ position push down on the locking tabs to secure your bed rail in place.
NOTE: After locking both buckles, check to make sure that the mesh wall of the bed rail is firmly up against the side of the mattress. There should be NO GAPS. If the mesh wall is not firmly against the side of the mattress, check to make sure the locking buckle is functioning properly and that the strap is not twisted beneath the mattress. Once this has been checked and corrected if needed, unlock the buckle, pull on the end of the strap tightly and lock the buckle again. Store the excess anchoring strap material by tucking it under the mattress. Do not cut excess strap, may cause strap to fray.

Operating the Swing Down Feature

With the bed rail side in the ‘up’ position, release the locking tabs on each swing lock and arm assembly by pushing them up. This will allow the upper part of the bed rail to move freely.
NOTE : Be sure to continue to hold the upper part of the bed rail so that it does not drop down on its own.
With both locking tabs turned to the ‘open’ position, hold the upper part of the bed rail firmly and swing it down. The bed rail should now be in the ‘down’ position. To return the bed rail to the ‘up’ position, reverse STEPS 1 – 2.
NOTE: Make sure that the bed rail is in the ‘up’ position and the locking tabs are securely closed before leaving a child alone in the bed.

Replacement Parts

regalo-2020-Swing-Down-Bed-Rail-Guard-FIG-15

MODEL 2020

Swing Down Bed Rail

SD – Mesh Wall
White = #23069

MODEL 2220

Extra Long Swing Down Bed Rail

XLSD – Mesh Wall
White = #23076

WARRANTY

90 DAYS LIMITED WARRANTY
If, during the ﬁrst 90 days after consumer purchase of the item, under reasonable and non-commercial use and conditions of maintenance, it fails while owned by the original purchaser because of the quality of materials or workmanship of ﬁnish and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option. PROOF OF PURCHASE REQUIRED.

WARNING

SUFFOCATION AND STRANGULATION HAZARD.
Gaps in and around bed rails have entrapped young children and killed infants.
NEVER use with children younger than 2 years old. USE ONLY with older children who can get in and out of adult bed without help.
NEVER use in place of crib.
NEVER use unless bed rail is tight against mattress, without gaps, and at least 9 in. from headboard and footboard. Do not ﬁll gaps with pillows, blankets, or other items that can suffocate children.
NEVER use on toddler bed, bunk bed, water bed, or bed with inﬂatable mattress. Use ONLY on adult bed.
Use ONLY on a bed ranging from twin size to queen size.
Use ONLY on adult bed with box spring and mattress.
This bed rail is NOT recommended to be used on a platform or similar style bed.
This bed rail is intended for use with children 2 years to 5 years of age.
Discontinue use if damaged, broken, or if parts are missing.
Do not use if bed rail is not fully assembled.
Periodically check that all spring pins are fully engaged on bed rail support bars.