SZELAM EN8853B-RGB Projection Alarm Clock User Guide

PROJECTION RGB
ALARM CLOCK
EN8853B-RGB
USER MANUAL

NOTES

1. Some scratches appear on the protective film due to long-distance transportation, please tear the protective film off before using. (Tips: As our protective film is very thin and fit well, which requires a little patience to find it and tear off.)
2. Please remove plastic insulator tab from button battery compartment in the back and connect the product with electricity by USB or Adapter.
3. The supplied battery is only for memorizing the time settings; it just could keep time memory when power off, couldn’t support the digital clock light up.
4. If time mode is 12 hour mode, when is Moming Time, there is “AM” symbol in display. When is Afternoon Time, there is “PM” symbol in display.
5. When the alarm beeps, the red bottom lighting will flash, then recovery to preset status after the alarm stops.
6. Automatic dimming set only works for screen displays.

PRODUCT PARAMETER

1. RGB LED Time display ( 4 Dynamic RGB Changing Color and 7 Regular Color).
2. There are 6 levels of brightness ( 100%-80%-50%-30%-10%-OFF).
3. Automatic dimming set.
4. Total 8 functional buttons (See the Introductions of buttons)
5. 12/24 hour modes selectable( The default is 12 hour mode).
6. The default Alarm display is 6:00.
7. Alarm buzzer volume adjustable (55dB-65dB-750B-850B-95dB).
8. Alarm with Pre-settable Snooze function ( 5-60 minutes and unlimited times).
9. Bottom RGB Light ( 10 Lighting Colors and brightness dimmable).
10. 180° Rotatable Projector (Bright- Slightly Bright-Dim-Off) .
11. There are 1 USB and 1 Type C Output ports on the side (5, 1A) which allows you to charge
    Android or Apple system smart phone in the same time.

INTRODUCTION OF BUTTONS

OPERATING INSTRUCTIONS

Note: Please connect the power cable into the jack (INPUT) on the left side of the alarm clock and then plug the power cable into the socket.
The LED display turns on.

SWITCHING 12/24HR TIME MODE

When itis in time mode (The defaultis 12 Hour mode), press the “SET” button to change the 12/24Hr time mode, the corresponding AM/PM icon will be light on/off

TIME SETTING

1. When itis in time mode, press and hold the *SET” button for 2 seconds to enter into time-setting mode, the hour digits flash. Press  button to set the current hour (hold to advance rapidly). (As shown i Figure 1)2. Press “SET” button again, the minute digits flash. Press bution to set minute. (As shown in3. Press “SET” button again, save and exit time-setting mode.

ALARM AND SNOOZE SETTING

1. When it is in time mode, press “AL” button to switch onoff the alarm, the corresponding will be light on/off.

2. Press and hold *AL” button for 2 seconds to enter into alarm-setting mode, the hour digits flash. Press   button to set hour (hold to advance rapidly). (As shown in Figure 3)

3. Press “AL” button again, the minute digits flash. Press   button to set minute. (As shown in Figure 4)

4. Press “AL” button again, save and enter into snooze-time setting mode (“05″ digit is flashing).
   (As shown in Figure 5)

5. Press button to set the current snooze time. (Default § minutes, 5-60 minutes adjustable).

6. Press “AL” bution again, save and exit snooze-time setting mode

ALARM BUZZER VOLUME

1. When itis in time mode, press VOL button to enter into volume setting, the volume digits flash.
2. Continue to press VOL button to adjust the alarm buzzer volume.(As shown in Figure 6)♦ Buzzer Volume: 550B-65dB-75dB-85dB-95dB.

WHEN THE ALARM BEEPS

1. BUZZER alarm last for 2 minutes.
2. When the alarm beeps, press button to enter snooze mode. The corresponding “ ” symbol flashes ill reach to the snooze time set and then alarm again.
3. When the alarm beeps, press any other buttons except the button to turn off the alarm and snooze. “ ” symbol stops flashing.

AUTOMATIC & MANUAL DIMMING SET

1. Press and hold button for more than 2 seconds. “OFF” displays which means manual mode(The default is “OFF”). In manual mode, press the “ + ” button to select light brightness: 100%-80%-50%-30%-10%-OFF by cycle.
2. Press and hold  button for more than 2 seconds. “ON” displays which means ‘auto mode. Which means the brightness is changing automatically by the environment, when the environment s dark, the brightness is low; when the environment s bright, the brightness is high.

CHANGING COLORS OF THE LED DISPLAY

When itis in time mode, press ( ) button to change the color of the LED dlsplay (As shown in Figure 7) The 11 colors sequence: Random Color- RGB Changing- RGB Left to Right Flowing – RGB Downward Top Flowing – White – Red -Yellow – Green – Light Blue-Blue-Purple

SETTING BOTTOM RGB LIGHT

1. When itis in time mode, press bution(in the back) to adjust the bottom light.

2. Continue o press the buttor can change colors. (As shown n Figure 8) The 10 colors sequence: RGB Flowing (Default)
   – RGB Changing- RGB Breathing – Warm White
   – Red -Yellow – Green – Light Blue – Blue – Purple.

3. Press and hold button for 3 seconds to turn OFF the light

4. Continue to press “-“ button to adjust the brightness.

USE PROJECTION

1. When itis in time mode, press bution once in the AC mode to turn on the projection (bright), continue to press to adjust the brightness. (As shown in Figure 9) (Bright-slightly bright- dim-off, defaultis off)
2. When the projection is on, press and hold button for 3 seconds to revolve projection view.
   (Rotate the projection 180 degress).

CHARGING

Connect the charging cable of your mobile phone to the USB ports on the left side of unit, then connect the other end to your mobile phone or other equipment. The clock will charge the mobile phone automatically.
Notes

1. Use the orginal cable of your mobile phone for charging.
2. Charge with this USB jack may take a long time.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>