Aqua Creek Products Pool Lift Mighty 600 User Manual
- June 4, 2024
- Aqua Creek Products
Table of Contents
- Aqua Creek Products Pool Lift Mighty 600
- Mighty 600 Lift
- Mighty 600 Components
- Installation: ADA Guidelines
- Anchor Installation: Core-drill Retro-fit (Typical Concrete Pool Deck
- Anchor Installation: Saw-cut Retro-fi t/New construction
- Mighty 600 Assembly Instructions
- Footrest Installation Instructions
- Basic Troubleshooting
- Battery Test Cable Instructions
- Pinch Point Locations
- Proper Care of Pool & Spa Lifts
- Mighty 600 Parts List
- AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY:
- Maintenance Notes
- Documents / Resources
Aqua Creek Products Pool Lift Mighty 600
Mighty 600 Lift
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING
WARNING – To reduce the risk of injury, do not permit children to use
this product unless they are closely supervised at all times.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
A wire connector is provided on the unit to connect a minimum 8 AWG (8.4mm2)
solid copper conductor between this unit and the means for local equipotential
bonding.
Check the unit periodically for signs of deterioration: Keep all nuts, bolts
and screws tight to be sure the lift is in safe working condition.
SAVE THESE INSTRUCTIONS
Affix supplied ADA POOL/SPA LIFT sign in a location visible from the lift at
all times.
Rechargeable batteries are to be removed from the appliance before being
charged. Batteries are to be inserted with the correct polarity. If the
appliance is to be stored unused for a long period of time, the batteries
should be removed and stored on the wall mounted charger to maintain the
battery charge. The supply terminals are not to be short-circuited.
REDUCE THE RISK OF DROWNING!
Supervise children at all times.
No jumping or diving from the lift.
Seat may be hot, use caution when entering.
Keep covered when not in use. Inspect and clean before use.
INDOOR BATTERY CHARGER:
AMPERAGE = 0.65 FREQUENCY = 60
Mighty 600 Components
- BASE AND MOTOR ASSEMBLY
- CONTROL ARMS
- LIFTING ARM
- ADJUSTABLE SEAT ARM
- TOP CASING ASSEMBLY
- FOOTREST
- LINAK ACTUATOR
- VITO 24 V BATTERY
- HANDSET
- HARDWARE BAG
Installation: ADA Guidelines
ADA REQUIREMENTS (For Commercial Applications):
The Mighty 600 lift is completely ADA compliant when installed correctly. The
installation must meet the following requirements:
- Clear deck space dimensions (see FIGURE 1)
- Install lift a minimum of 22 inches from the pool edge (For curved pool walls contact Aqua Creek for placement)
- Deck slope no greater than 1:48
- The seat must be submerged at least 18 inches into the water. The lift should be installed at a location with 42-48 inches of depth (deck to pool floor)
NOTE: Other requirements may be necessary based on local code
requirements. The anchor system should be bonded according to NEC Section 680
and/or local code requirements.
Anchor Installation: Core-drill Retro-fit (Typical Concrete Pool Deck
Installation)
Your deck MUST have:
- Minimum footing size: 4’ – 6” x 4’ – 6” x 10” thick.
- Minimum concrete strength: 4500 psi
- Reinforcement: #5 rebar @ 10” on center (O.C.)
TOOLS REQUIRED:
- CORE DRILL
- 3” CORE DRILL BIT
- 1 1/2” CORE DRILL BIT
- MARKING PEN
- AIR NOZZLE & PUMP/COMP.
- HEAT GUN (OPTIONAL)
*Use HILTI RE-500-SD adhesive anchor or SIMPSON SET-XP anchor adhesive or equivalent.
NOTE: Your local codes may require one or more permits. Check with your
local building codes for the proper permit requirements.
-
Mark the center of the anchor location on your deck using the guidelines on page 4. Also mark the center for the fixing anchor 3 1/2 from the center anchor.
-
Using a diameter core-drill bit, drill a diameter hole at the anchor location. Make sure to keep the bit square to the deck. Drill straight down to a depth of at least 6. Then use a 1 1/2 drill bit for the fixing anchor, drilling down at least
NOTE: Create a depth marker on the drill bit with black electrical tape to make sure you drill to the right depth. If you drill through the deck you may need to use the saw-cut installation instructions. -
Remove plug and clean out the holes with a wire brush. Insert an air nozzle to the bottom of the hole. Use a pump or compressed air to blow out the hole. A heat-gun may be helpful in drying out the hole.
-
Place the anchor in the hole and ‘dry-fi t’ it first to make sure the anchor will be flush and plumb with the finished deck surface when installed. Adjust the hole as needed.
NOTE: Pool decks with pavers or thick tiles may require other anchor options. Contact Aqua Creek Products. -
Inject epoxy adhesive into each hole starting at the bottom until the hole is 1/3 to 1/2 full.
NOTE: We recommend using masking tape around the top of the anchors so that no epoxy gets inside the anchors.
-
Install the anchor into the epoxy filled hole by pushing down and twisting back and forth to evenly distribute the epoxy around the anchor. Push down until it is flush with the finished deck surface. Clean off any excess epoxy. Adjust the anchor as needed to make sure it is flush and plumb with the deck surface. This should be done during the adhesives’ specified ‘gel time’ (see epoxy manufacturers’ instructions).
-
Let the epoxy cure for at least 24 hours before installing the lift (or where applicable according to the epoxy manufacturers’ instructions).
Anchor Installation: Saw-cut Retro-fi t/New construction
-
Mask the bottom hole of the anchor sleeve to prevent concrete from seeping in.
-
Install rebar in the 4-6 x 4-6 section of the deck that will be thickened to 10. SEE FIGURES B & C.
-
Set the bronze anchor sleeve in place. Make sure the center of the anchor sleeve
is no more than 44 from the pool’s edge. Set the fixing anchor insert 3 1/2 from the center of the anchor sleeve. Fixing anchor may be located anywhere on the deck, as long as it is 3 1/2†from the center of the anchor sleeve. SEE FIGURE B. -
Bond the anchor sleeve according to your local code requirements by using the bonding lug and bonding screw on the side of the anchor sleeve.
-
Pour your concrete and finish the pool deck surface.
-
Once the concrete has cured, your lift is ready to be mounted into the anchor sleeve.
Mighty 600 Assembly Instructions
-
Lift the Mighty 600 MAIN ASSEMBLY from the shipping container. Insert the 1.9” [48mm] post of the MAIN ASSEMBLY into the deck anchor (FIGURE A, PAGE 6). Ease the MAIN ASSEMBLY down until it rests on the deck surface. Rotate the base until the fixing anchor hole lines up with the
fixing anchor. Install the 1/2” x 1 1/2” hex bolt and washer to hold down the lift. Tighten the bolt. -
‘Remove all of the shipping materials from the lift. Slide the CHAIR AND CHAIR ARM ASSEMBLY up through the top casing of the MAIN ASSEMBLY and connect using the supplied 5/16” hex bolts, washers and nylock nuts. For standard pool configuration the CHAIR ARM will be connected
at the top two holes. However, the chair arm can be adjusted up to 6 inches higher, in 2 inch increments, if there is a need for it. NEVER USE THE LIFT WITHOUT BOTH HEX BOLTS INSTALLED!
Footrest Installation Instructions
The Aqua Creek footrest assembly is designed to fi t under the chair and is installed inside the 2” square tubing that supports the chair from underneath. To install the footrest;
- Insert the footrest assembly into the 2 x 2 square tubing that supports the chair until the plastic insert of the footrest assembly sits fl ush against the end of the 2 x 2 tube.
- Using the supplied 1/4” hardware, fasten the largest assembly to the 2 x 2 tubing.
Basic Troubleshooting
Problem: The lift won’t move.
Solution:
-
Make sure the cords are properly plugged in:
-
Check the contact points:
-
Make sure the battery is fully charged:
Problem: The lift stopped moving and is stuck.
Solution:
- Press the Emergency button
Press the emergency retract button on the front of the control box to retract the lift.
Note: the lift will not retract if the battery is not fully charged or if the control box is not working. The emergency but-ton only overrides the remote handset.
Note: If you feel your lift is malfunctioning due to a faulty battery or connections, contact Aqua Creek Products for a testing kit.
Battery Test Cable Instructions
WARNING! DO NOT ATTEMPT TO DIRECTLY PROBE THE BATTERY CONNECTOR TO TEST
VOLTAGE. THIS MAY CAUSE PERMANENT DAMAGE TO THE BATTERY! USE THE SUPPLIED
BATTERY TEST CABLE ONLY FOR CHECKING THE BATTERY VOLTAGE!
The Aqua Creek 24V battery has a cable and connector for connecting to the
control box or to the battery charger. The battery connector is not suitable
to check the battery voltage, as it is very hard to probe the connector
without shorting-out the battery, which will cause damage. For this reason, a
separate battery test cable is provided. To safely check the battery voltage,
use a voltmeter or multi-meter with standard test probes, and insert the
probes into the test cable as shown below.
Pinch Point Locations
Proper Care of Pool & Spa Lifts
PROCEDURE| BEFORE
EACH USE
| DAILY| WEEKLY| MONTHLY
---|---|---|---|---
Check battery level indicator on control box| ü| | |
Run the lift through a complete test cycle (fully extend actuator) to
verify it is functioning properly| ü| | |
Wash lift with fresh water and dry with clean, soft, non-abrasive cloth|
| ü| |
Recharge battery| | ü| |
Visually inspect lift for damage, corrosion, and loose or missing
hardware| | ü| |
Check all contact points for damage and/or corrosion| | | ü|
Repair, clean, and apply dielectric grease to all contact points|
| | ü|
Thoroughly clean lift frame and apply a liberal coat of car wax to maintain
the lift’s finish| | | | ü
Check all warning and cautionary labels to make sure they are not faded or
worn. Replace as needed.| | | | ü
PROPER CARE NOTES
- Use only fresh water to wash your lift. Do not wash with pool water.
- Use only clean, soft, non-abrasive cloths on your lift.
- Do not store lift in pump room or near chemicals.
- Do not allow children to play on or around this lift.
- When cleaning the lift, do not spray water directly on control box or battery.
- The lift may need to be bonded according to local code requirements.
- If the lift is not used for extended periods, remove the battery from the lift and store it on the wall charger to maintain the batteries charge. The charger should be plugged in and in a climate controlled area.
STAIN REMOVAL TIPS:
To remove stubborn stains from finish, spray affected area with mild dish
soap, rub briskly with a 3M Scotch Brite™ pad. Use white epoxy paint to touch
up the finish. Apply wax to protect when dry.
For service and/or replacement parts, contact Aqua Creek Products Toll free:
888-687-3552
Mighty 600 Parts List
ITEM # | QTY | PART # | DESCRIPTION |
---|---|---|---|
1 | 1 | MTY-100WM-00 | ANCHOR SPINDLE WELDMENT |
2 | 1 | MTY-200WM-00 | MAIN FRAME WELDMENT |
3 | 2 | MTY-400-00 | CONTROL ARM ASSEMBLY |
4 | 1 | AMTY-600-00 | TOP CASING ASSEMBLY |
5 | 1 | MTY-700-00 | CHAIR CRADLE ASSEMBLY |
6 | 1 | AMTY-800-00 | LIFTING ARM ASSEMBLY |
7 | 1 | MTY-900-00 | MIGHTY MOTOR ASSEMBLY |
8 | 1 | F-905WCB | 22” CHAIR ASSEMBLY |
9 | 1 | F-FRB-03 | FOOTREST ASSEMBLY |
10 | 1 | 341185-01 | ACTUATOR, LINAK, 600MM |
11 | 1 | VCB10 | VITO CONTROL BOX |
12 | 1 | VCP100-29800 | VITO 24V BATTERY |
13 | 1 | GT10 (CONTROL BRACKET) | VITO MOUNTING BRACKET |
14 | 1 | K50X55X20H | NEEDLE ROLLER BEARING |
15 | 1 | 93576A250 | SPIRAL EXTERNAL RETAINING RING |
16 | 1 | 94751A785 | EXTERNAL RETAINING RING |
ITEM # | QTY | PART # | DESCRIPTION |
--- | --- | --- | --- |
17 | 1 | BEARING, ROLLER LM67048 | ROLLER BEARING & RACE |
18 | 1 | INV01703 | 1” CLAMP ON SHAFT COLLAR |
19 | 4 | BSH 10 X 3/8 | #10 X 3/8 SOCKET HEAD |
20 | 2 | WF 10 | #10 FLAT WASHER |
21 | 4 | BHW 1/4 X 3/8 | 1/4-20 X 3/8 HEX WASHER BOLT |
22 | 2 | BH 5/16 X 3 | 5/16-18 X 3 HEX BOLT |
23 | 1 | BH 5/16 X 4 1/2 | 5/16-18 X 4 1/2 HEX BOLT |
24 | 8 | WF 5/16 | 5/16 FLAT WASHER |
25 | 5 | NN 5/16 | 5/16-18 NYLOCK NUT |
26 | 2 | BS 3/8 X 2 18-8 | 3/8 X 2 SHOULDER BOLT |
27 | 8 | NN 3/4 | 3/4-10 NYLOCK NUT |
28 | 1 | TS 3/4 X 6 | 3/4-10 X 6 THREADED STUD |
29 | 1 | TS 3/4 X 8 | 3/4-10 X 8 THREADED STUD |
30 | 2 | TS 3/4 X 10 1/2 | 3/4-10 X 10 1/2 THREAD STUD |
31 | 3 | 14530 | 3/8 DIAMETER ROUTING CLIP |
32 | 1 | F-UBC | UNIVERSAL BATTERY COVER |
33 | 1 | F-MTMC | MIGHTY MOTOR COVER |
AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY:
MIGHTY LIFT SERIES (ITEM #’s F-MTY400 & F-MTY600)
Aqua Creek Products, LLC (a.k.a. Aqua Creek) warrants to the original end user
purchaser that products manufactured by Aqua Creek, when properly installed in
accordance with assembly and installation instructions, and properly used and
maintained, shall be free from defects in material and workmanship for a
period of five (5) years from the date of original purchase, provided that
Aqua Creek receives prompt notice in writing of any defect or failure and
satisfactory proof thereof, with the following exception(s):
Exceptions:
- All electrical components, including the linear actuator shall have the following warranty period:
- Year 1-2: 100% Coverage
- Year 3: 60% Coverage (Customer is responsible for 40% of replacement cost)
- Year 4: 50% Coverage (Customer is responsible for 50% of replacement cost)
- Year 5: 40% Coverage (Customer is responsible for 60% of replacement cost)
- Hydraulic actuators and mesh slings shall have a warranty period of one (1) year from the date of original purchase.
- Powder coat finish scratches, scrapes, corrosion, or dents from customers normal use, negligence, or abuse
This warranty specifically excludes reimbursement for labor to remove, repair, or install the product and any shipping charges. These warranties do not cover any damages due to accident, force majeure, act of nature, misuse, abuse, negligence or failure to properly maintain any products, or normal wear and tear from day to day operations. In the event that any products are altered, repaired, or improperly installed or improperly used by anyone without the prior written approval by Aqua Creek, all warranties are void. IMPORTANT: AMOUNT OF WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED LIFTING CAPACITY FOR THE LIFT. NEVER OPERATE THE LIFT UNDER LOAD IN A DRY POOL (WITH NO WATER IN THE POOL). It is the responsibility of the lift owner to verify the weight of the patron for warranty claim purposes and to ensure that the lift is not overloaded. Non-payment for product to Aqua Creek may void warranty.
To initiate a warranty claim, the owner of an Aqua Creek product must provide
the place of purchase, in writing, with a full description of the product, its
serial number, the dates of purchase and installation, and the exact nature of
the defect. Within thirty (30) days after receipt of a written warranty claim
by Aqua Creek, and barring any unforeseen delays, the place of purchase will
be notified of Aqua Creek’s decision regarding the claim.
If requested by Aqua Creek, any defective product must be returned, freight
prepaid by customer, to Aqua Creek’s designated factory location or duly
appointed distributor for inspection and/or repair. Aqua Creek will, at its
option, repair or replace the failed or defective item, and deliver the
repaired product or replacement to the customer. All freight charges are the
responsibility of the customer. Products returned to Aqua Creek for which Aqua
Creek provides replacement under this limited warranty shall become the
property of Aqua Creek. A new warranty period shall NOT be established for the
repaired or replaced products. Such products shall remain under warranty only
for the remainder of the original warranty period on the original products
purchased.
This written limited warranty constitutes the final, complete and exclusive
statement of warranty terms. No person or organization is authorized to make
any other specific or implied warranties or representations on behalf of Aqua
Creek.
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED, INCLUDING WITHOUT
LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
OR USE.
THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH
RESPECT TO THE PRODUCTS SHALL BE LIMITED TO REPAIR OR REPLACEMENT AT AQUA
CREEK’S DESIGNATED FACTORY LOCATION, OR DULY APPOINTED DISTRIBUTOR, OR IN
PLACE AT AQUA CREEK’S OPTION. IN NO EVENT SHALL AQUA CREEK’S LIABILITY EXCEED
THE ENTIRE AMOUNT PAID TO AQUA CREEK BY THE ORIGINAL PURCHASER FOR THE FAILED
OR DEFECTIVE PRODUCT.
IN NO EVENT SHALL AQUA CREEK PRODUCTS, LLC BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL, INDIRECT, PUNITIVE OR EXEMPLARY DAMAGES OR LOST
PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SO
SOME OF THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
LIFT / INSPECTION INFORMATION
Test Date: | For Additional Support Assistance Call: |
---|---|
Pool Lift Model Here: | Toll Free: 888‐687‐3552 |
Serial Number: | International: 1+ 406‐549‐0769 |
Inspected by: |
Find additional troubleshooting info and videos at: https://aquacreekproducts.com/help‐center/trouble‐shooting/
**Maintenance Notes**
Please read and fill out all information carefully
Improper use and/or maintenance of a pool lift can lead to actuator and/or
other mechanical failures and possible personal injury. Please read and follow
the product operators’ manual and the instructions below.
- NOTE: Completely cycle the lift without a load before each use to verify the lift is functioning
- Product service life depends on the load characteristics, type and frequency of use, and the environment in which the product is being For example, persons not calmly sitting but falling down with their full body weight in the chair, or using the pool lift’s chair as a diving platform can cause premature actuator failure and/or possible personal injury.
- Based on historical product service life analysis, Aqua Creek recommends replacing the actuator(s) and other electronic components after 5 years of service. Check component serial numbers and purchase records to verify the age of your components.
- A functional weight lifting force of a maximum of 100 lbs must be periodically verified by applying a non‐live load (without a person) through the entire operating cycle of the lift. This process is performed in order to verify the smooth operation. Make note of any unusual noises or sudden movements coming from the actuator(s) or other components. Note: In some lifts, a sudden quick movement at the beginning of the cycle is normal but should smooth.
- Creating a side load on the actuator by pushing and/or pulling on the actuator, especially under load conditions, can cause damage to the actuator and/or personal injury.
- Electronic components are designed to be plug‐and‐play type There is no need to access the internal mechanisms in these components. The actuator, battery, and all electronic components may only be disassembled by authorized factory‐trained personnel. Disassembly of electronic components by improperly trained and unauthorized persons will void the warranty on those components.
- The operator of the pool lift should never allow the pool lift to hit any stationary object either vertically or horizontally while operating a pool lift, e. walls, ceiling, pool/spa bench, etc.
- For quick and accurate troubleshooting and inspections, we recommend having a voltage meter, Vito Battery Check Cable (Item F‐VTC002) and an Aqua Creek Test Light (Item F‐01TL) on hand as well as adequate test and replacement components.
- Remove the pool lift from service immediately if any unusual noise is heard coming from the actuator such as grinding, popping or sudden inconsistent
- Immediately remove from service any lift that does not have 100% compliance with the inspection
. Overall isual Inspection
Corrosion is common with anything in a swimming pool environment; even
stainless steel. Proper and regular maintenance and cleaning will prevent most
instances of corrosion. Replace any components that have corrosion caused
pitting, cracking, thinning of the base metal, or other instances of corrosion
that can’t be eliminated and/or minimized through a thorough cleaning. Refer
to product manual for additional maintenance instructions. Make comments
and/or recommendations in the notes area below each section.
Inspection Item
Pass Fail
N/
a. Anchor bolts, concrete around anchors, etc… are in good condition. No
cracks in concrete, missing hardware, and anchors are installed correctly.| |
|
b. The fixing anchor is installed correctly and is in good condition.| |
|
c. Powder coated components are clean, corrosion free, and in good
overall condition. Clean and repair any missing powder coat finish. Apply a
coat of wax on the cleaned and repaired finish.| | |
d. Welded Joints show no signs of cracks or fatigue. Replace any
non‐compliant components| | |
e. Hardware is present, secure, and not corroded (bolts, nuts, bushings,
etc…).| | |
f. All wiring routing clips are present and in good condition.| | |
g. All product warning labels are present and legible.| | |
h. Plastic seat, foot rest, and other plastic components are present and
in good shape.| | |
i. Arm rest hand grips are present, in good condition, and are well
secured to the arms.| | |
j. Electronic and Lift covers are present and in good condition (Lift
covers are highly recommended for outdoor installations).| | |
k. Inspect rotation gears for any damage or missing teeth. Inspect
rotation motor gear and alignment to ensure proper rotation of the lift.| | |
l. Inspect lift slings, seat belts, and other similar stitched and webbed
or weaved materials for damage, fatigue, and/or deterioration. Replace at
first sign of any fatigue or damage.| | |
NOTES/RECOMMENDATIONS:
. Electronics Inspecti n
Most electronic issues are due to poor electrical connections and/or a defective battery. Always remove the battery and place on the charger when the lift is not in use. NOTE: Even if your lift is equipped with a solar charger, it is a good idea to place the battery on the wall charger periodically or during extended periods of non‐use or storage. Before testing the battery, charge overnight. A voltage meter is required for this section and a known GOOD handset controller is helpful. An Aqua Creek electronics test light is also highly
recommended (Order item F‐01TL). Make comments and/or recommendations in the notes area below each section.
Inspection Item
Pass Fail
N/
a. Battery contact points are free of damage and/or corrosion. Dielectric
grease is present on all conta t points to prevent corrosion. ALWAYS STORE
BATTERY ON THE CHARGER WHEN LIFT IS NOT IN USE!| | |
b. Battery level indicator (if equipped) on control box is functioning
properly when battery is installed on lift.| | |
c. Using the voltage meter check the voltage on the battery. A good battery
should read between 24v and 28v DC. Note: Vito batteries will require a test
cord (F‐ VTC002)| | |
d. Using the test light, confirm continuity through the control box by
plugging the light into the control box in place of the actuator and press the
buttons on the
controller and the control box itself (if applicable). If light does not light up with handset, replace handset with a known good one and try to see if it lights up.
| | |
e. Once the battery is fully charged up to 24 to 28 volts, cycle the lift (up,
down, rotate) counting the cycles. If the battery is in good condition, the
lift should easily complete at least 15 cycles without a load.| | |
NOTES/RECOMMENDATIONS:
. Physical Pool Lift Test
A physical test of the lift function is required when doing an annual
inspection. NOTE: The lift should always be run through a complete cycle
without a load prior to each use. The annual test should be ran both empty and
with a typical load weight to test the lifts functions. Make comments and/or
recommendations in the notes area below each section.
Inspection Item Pass Fail
N/
a. With all connections connected, operate the lift though a complete
cycle without weight to confirm the lift is functioning correctly. Note any
strange noises and any unusual operation.| | |
b. Verify the lift was installed correctly; is the lift free to travel in
and out of the pool without hitting anything like a wall, rail, bench, etc..|
| |
c. Rotate lift at least 90 degrees over the water and back again if
applicable| | |
NOTES/RECOMMENDATIONS
Documents / Resources
| Aqua
Creek Products Pool Lift Mighty
600
[pdf] User Manual
Pool Lift Mighty 600, Pool Lift, Mighty 600, Pool Mighty 600, Mighty 600 Pool
Lift, F-MTY600-03
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>