Hunter 50854 Whittier Indoor Matte White Ceiling Fan Instruction Manual
- June 17, 2024
- Hunter
Table of Contents
- Hunter 50854 Whittier Indoor Matte White Ceiling Fan
- Product Usage Instructions
- Here is what comes in your box
- Choosing the Right Installation Location
- Checking the Ceiling Angle
- Angled Mounting
- Installing the Ceiling Bracket
- Installing the Downrod
- Hanging the Fan
- Wiring the Fan
- Installing the Canopy
- Installing the Blades
- Assembling the Light
- Installing the Bulbs and Glass
- Installing the Pull Chains
- Reversing the Fan
- Troubleshooting
- Limited Lifetime Warranty
- Downrod
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Hunter 50854 Whittier Indoor Matte White Ceiling Fan
Product Specifications
- Model: PG3902
- Manufacturer: Whittier
- Standard: UL Standard 507
Product Usage Instructions
Tools Required for Installation
Before starting the installation process, make sure you have the following
tools:
- Screwdriver
- Pliers
- Wire Strippers
- Drill
- 9/64 Drill Bit
- Ladder (if mounting to a support structure)
Unboxing and Hardware Identification
When you receive your ceiling fan, follow these steps:
- Open the box and take out all the components.
- Lay out the components and group them according to the drawn components in the manual.
- Take note of the symbol printed on each hardware bag for easy identification during installation.
Removing Shipping Blocks or Ring
Before installing the fan blades, ensure you remove the shipping blocks or
ring from the motor. Save the screws as they will be needed for blade iron
installation.
Installation Location
Choose the right location for installing your ceiling fan by considering the
following:
- Check the room dimensions:
- Ensure there is at least 30 inches of clearance from blade tip to the nearest wall or obstruction.
- Maintain a minimum distance of 7 feet from the bottom edge of the blade to the floor.
- Check the outlet box:
- Make sure you can secure the fan to the building structure or a fan-rated outlet box.
- If you are using angled mounting, ensure the ceiling outlet box is compatible.
Frequently Asked Questions (FAQ)
What should I do if I find a missing or damaged part?
If you find a missing or damaged part, please do not return it to the store.
Contact us at HunterFan.com or call us at 1.888.830.1326, and we will assist
you in resolving the issue.
Can I use this ceiling fan in rooms with angled ceilings?
Yes, this ceiling fan supports angled mounting. However, make sure you have a
compatible ceiling outlet box for angled installation.
Model: 50854 Matte White
Fan weight ±2 lbs: 20.7 lbs (9.4 kg)
Congratulations on purchasing your new Hunter® ceiling fan!
Here are the tools you’ll need to complete your installation:
The ceiling fan you purchased will provide comfort and performance in your
home or office for many years. This instruction manual contains complete
instructions for installing and operating your fan. We are proud of our work
and appreciate the opportunity to supply you with the best ceiling fan
available anywhere in the world.
We are here to help!
This Instruction Manual is designed to make installation as simple as
possible. While working through this Instruction Manual, keep your smartphone
or tablet nearby. We have added video links to help you through the more
technical sections. If you are unfamiliar or uncomfortable with wiring,
contact a qualified electrician. We also provide telephone support at
1.888.830.1326 or visit us at HunterFan.com.
READ and SAVE These Instructions
Warning
-
w.1 – To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the
mounting screws provided with the outlet box. -
w.2 – To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you
cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. -
w.3 – To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.
-
w.4 – To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
Caution
- c.1 – All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
- c.2 – Use only Hunter replacement parts.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: modifications not approved by the party responsible for
compliance could void user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
This product conforms to UL Standard 507.
Here are the tools you’ll need to complete your installation:
Here is what comes in your box
Hunter Pro Tip:
Do not discard the hardware bags or mix parts from different bags. Make
note of the symbol printed on each hardware bag. The symbols can be used to
identify the appropriate hardware for each step.
Find a part that is missing or damaged?
Don’t take it back to the store. Let us make it right. Visit us at
HunterFan.com or call us at 1.888.830.1326.
Choosing the Right Installation Location
You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit.
Checking the Ceiling Angle
-
If you have a flat ceiling:
Hang your fan by a standard downrod. Some fans come with a shorter downrod for a Low Profile installation. -
If you have an angled or vaulted ceiling:
- You will need a longer downrod. (sold separately at HunterFan.com)
- If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit. (Sold separately at HunterFan.com)
Angled Mounting
A little more information on Angled Mounting:
For optimum performance and appearance, a longer downrod should be used with
your Hunter ceiling fan when installing on high or angled ceiling. If your
ceiling is angled greater than 34° you will also need an Angled Mounting Kit.
Longer downrods and the Angled Mounting Kit are sold separately at
HunterFan.com.
Hunter Pro Tip:
Determining if you need an Angled Mounting Kit:
Fold on the dotted line. Place against edge against the wall. Slide towards
the ceiling.
If the guide touches the wall but not the ceiling, you need an angled mounting
kit.
Installing the Ceiling Bracket
You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box.
Hunter Pro Tip:
The machine screws are the ones that came with your outlet box.
Do this first!
WARNING
To avoid possible electrical shock, before installing your fan, disconnect the
power by turning off the circuit breakers to the outlet box associated with
the wall switch location.
Option 1:
Machine Screws
Use machine screws (provided with outlet box) and washers when securing to
existing ceiling fan-rated outlet box. Make sure it is securely installed and
is acceptable for fan support of 31.8 kg (70 lbs) or less.
Option 2:
Wood Screws
Use wood screws and washers (included) when securing to support structure with
approved electrical outlet box. Drill 9/64” pilot holes in support structure
to aid in securing ceiling bracket with hardware found in the hardware bag.
Installing the Downrod
Follow below if you are using the downrod that came pre-assembled in your box. Need to install a longer or shorter downrod? Check out the guide at the end of this manual.
WARNING
FAN FALL HAZARD
To prevent SERIOUS INJURY or DEATH:
- ALWAYS tighten setscrew with pliers.
- DO NOT hand tighten setscrew.
- CHECK the setscrew is tight using pliers each time you change fan direction.
Hanging the Fan
Wiring the Fan
We know wiring is hard. Let’s make it easier.
Follow these steps to get your fan wired quickly and safely. Follow the route
below that best matches your wall switch setup. If you are unfamiliar with
wiring or uncomfortable doing it yourself, please contact a qualified
electrician.
Hunter Pro Tip:
Here is how to connect the wires:
Push the bare metal ends of the wires together and slide a wire nut over them.
Then, twist the wire nut clockwise until tight.
Give it a gentle pull to make sure none of the wires are loose.
WARNING
The ceiling fan must be grounded. If the ground wire for the installation site
is not present, immediately STOP installation and consult a qualified
electrician.
All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
Hunter Pro Tip:
Have extra wiring?
Turn the wires upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one
side of the outlet box and the ungrounded wires on the other side of the
outlet box. Make sure that the wires are still attached to the wire nuts.
Installing the Canopy
Installing the Blades
Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade arm with screws found in the hardware bag.
Assembling the Light
-
Screw light kit screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose.
-
Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise.
-
Insert a third screw, found in the hardware bag, into place and then tighten all three screws.
WARNING
FAN FALL HAZARD Make sure all three screws are tight to secure the upper switch housing to the mounting plate. -
Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors.
-
Partially install two of the light kit screws found in the hardware bag. Align the notches in the sides of the lower switch housing with the screws on the upper switch housing. Twist the lower switch housing clockwise to lock into place.
-
Install the last light kit screw.
Tighten all three screws securely.
WARNING
FAN FALL HAZARD
Make sure all three screws are tight to secure the lower switch housing to the
upper switch housing
Installing the Bulbs and Glass
Hunter Pro Tip:
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click “How
do I install my fan without the light kit?”
WARNING
GLASS FALL HAZARD
To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured.
Installing the Pull Chains
Reversing the Fan
Troubleshooting
Fan Doesn’t Work
- Make sure power switch is on.
- Pull the pull chain to make sure it is on.
- Push the motor reversing switch firmly left or right to ensure that it is engaged.
- Check the circuit breaker to ensure the power is turned on.
- Make sure the blades spin freely.
- Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.
- Check the plug connection in the switch housing.
Excessive Wobbling
-
Make sure the blades are properly installed on the blade iron posts.
-
Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
-
Use the provided balancing kit and instructions to balance the fan.
Noisy Operation -
Make sure the blades are properly installed.
-
Check to see if any of the blades are cracked. If so, replace all of the blades.
Hunter Pro Tip:
Cleaning the Fan
Use soft brushes or cloths to prevent scratching.
Cleaning products may damage the finishes.
Limited Lifetime Warranty
Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com.
Thank you for choosing Hunter!
How Can Warranty Service Be Obtained?
Proof of purchase is required when requesting warranty service. The original
purchaser must present a sales receipt or other document that establishes
proof of purchase. Hunter, at its sole discretion, may accept a gift receipt.
To obtain service, contact Hunter Fan Company online or by phone.
www.HunterFan.com/Support/Contact-Us/
1-888-830-1326
Please do not ship your fan or any fan parts to Hunter. Delivery will be
refused.
What Does This Warranty Cover?
Motor — Limited Lifetime Warranty
If any part of your ceiling fan motor fails during your ownership of the fan
due to a defect in material or workmanship, as determined solely by Hunter,
Hunter will provide you with a replacement fan free of charge.* The foregoing
limited warranty applies only to the motor itself and does not apply to
electronic controls – such as remote control transmitters, remote control
receivers, or capacitors – used in conjunction with the motor. Such electronic
control items are included in the one-year limited warranty below.
Other — One-Year Limited Warranty
Except as otherwise indicated throughout this warranty, if any part of your
Hunter ceiling fan fails at any time within one year of the date of purchase
due to a defect in material or workmanship, as determined solely by Hunter,
Hunter will provide a replacement part free of charge.*
Light Kits — Warranty May Vary
Light kits are included in the one-year limited warranty. However, you may
qualify for additional warranty coverage if your fan includes one of the
following:
- LED Light Kits — Three-Year Limited Warranty
If your LED light kit module (not including glass components) or LED bulb fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.
If no replacement product/part can be provided for your fan, we will provide a comparable or superior replacement product/part at the sole discretion of Hunter.
What Does This Warranty NOT Cover?
Labor Excluded. This warranty does not cover any costs or fees associated with
the labor (including electrician’s fees) required to install, remove, or
replace a fan or any fan parts.
There is no warranty for light bulbs (except where otherwise noted); remote
control batteries; fans purchased or installed outside the United States; fans
owned by someone other than the original purchaser; fans for which proof of
purchase has not been established; fans purchased from an unauthorized dealer;
ordinary wear and tear; minor cosmetic blemishes; refurbished fans; and fans
that are damaged due to any of the following: improper installation, misuse,
abuse, improper care, failure to follow Hunter instructions, accidental damage
caused by the fan owner or related parties, modifications to the fan, improper
or incorrectly performed maintenance or repair, improper voltage supply or
power surge, use of improper parts or accessories, failure to provide
maintenance to the fan, or acts of God (e.g. flood).
ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH
RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH HEREIN.
HUNTER FAN COMPANY IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES,
DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE. Some States do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE
OF THE APPLICABLE LIMITED WARRANTIES SET FORTH ABOVE. Some States do not allow
limitations on how long an implied warranty lasts, so the above limitation may
not apply to you.
How Does State Law Affect Warranty Coverage?
This warranty gives you specific legal rights. You may also have other rights
which vary from state to state.
Downrod
If you need a different downrod length follow these steps:
Follow steps 1-5 to remove standard downrod pipe
WARNING
FAN FALL HAZARD
To prevent SERIOUS INJURY or DEATH:
- ALWAYS follow the downrod assembly instructions exactly.
- VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
References
- Hunter Fan Company - Online Ceiling Fan Store
- Manual-Hub.com - Free PDF manuals!
- Hunter Fan Company - Online Ceiling Fan Store
- Manual-Hub.com – Free PDF manuals!