StarTech S2510BPU33 Storage Drive Enclosure Instruction Manual

June 14, 2024
StarTech

StarTech S2510BPU33 Storage Drive Enclosure

StarTech-S2510BPU33-Storage-Drive-Enclosure-product.

2.5” Tool-less USB 3.0 to SATA III HDD Enclosure with UASP Support

S2510BPU33

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgment elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Product Diagram

Top View

Front View

USB 3.0 Micro-B (10 pin; SuperSpeed)

Introduction

Packaging Contents

  • 1x 2.5” USB 3.0 to SATA III HDD Enclosure
  • 1x HDD Pad
  • 1x USB 3.0 Cable
  • 1x Product Manual
System Requirements
  • Computer system with available USB 3.0 (5 Gbit/s) port or USB 2.0 port (480Mbps)
  • 2.5” SATA hard drive or solid state drive (9.5mm height)
  • Microsoft® Windows® 2000/XP/Server 2003/Vista/Server 2008 R2/7/8 (32/64-bit), or Apple® Mac® OS 9.x/10, or Linux®

Installation

Hardware Installation

WARNING! Hard drives and storage enclosures require careful handling, especially when being transported. If you are not careful with your hard disk, lost data may result. Always handle your hard drive and storage device with caution. Be sure that you are properly grounded by wearing an anti-static strap when handling computer components or discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds.

  1. Open the enclosure by sliding the top panel away from the USB port, and lifting from the enclosure base.
  2. Attach the included “HDD Pad” to the back side of the 2.5” Hard Drive, oposite the SATA connector.
  3. Connect the the 2.5” SATA Hard Drive
  4. Align the hooks on the top panel with the groves on the Base of the enclosure and slide the top panel back into place.
  5. With the enclosure fully assembled, connect the USB 3.0 cable from the enclosure to a USB port on the host computer system using the included cable.

StarTech-S2510BPU33-Storage-Drive-Enclosure \(7\)

How to Use

Connecting the Hard Drive
  • Once the enclosure has been attached to a computer, and the necessary software has been installed, the drive will be accessible as though it were installed within
    the system.

  • Prior to using the drive, it will need to be formatted according to your operating system requirements. To format your newly attached hard drive, or create partitions, please consult the documentation that accompanied your operating system at the time of purchase.

Powering the Drive Enclosure

The hard drive enclosure requires no external power supply, as it is capable of receiving enough power from the USB Bus to which it is connected.

LED Indicator

The hard drive enclosure offers an LED indicator, to enable you to monitor drive activity. When the enclosure is powered, the LED will illuminate. While the hard drive is being accessed, the LED will blink. Do not remove the enclosure from the host computer while the LED is flashing, as it could damage the drive or the enclosure, resulting in data loss.

Disconnecting the Hard Drive

Windows

  • Select the “Safely remove Hardware and Eject Media” icon, located in the taskbar.
  • Select “Eject USB Device” from the list that appears.
  • Wait for the message indicating that it is now safe to remove the device.

NOTE: Removing the connected drive prior to receiving notification that it is safe to do so, could result in losing or corrupting data stored on the drive. Once the Safe to Remove Hardware message appears, please disconnect the enclosure from the computer by removing the USB connection.

Mac OS X

To safely disconnect the attached drive from the host computer, close any windows listing the contents of the removable drive. Once all windows are closed, click on the USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop. Allow 5 seconds before physically removing the enclosure/drive from the computer.

Initializing the Hard Drive

  1. If the SATA Hard Drive is blank it may need to be initialized and formatted before use. From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/ 7 / 8), then select Manage. In the new Computer Management window, select Disk Management from the left window panel.StarTech-S2510BPU33-Storage-Drive-Enclosure \(8\)
  2. A dialog window should automatically appear, asking you to initialize the drive. Depending on the version of Windows, it will give you the option of either creating an “MBR” or “GPT” disk. GPT (GUID partition) is not compatible with some older operating systems, while MBR is supported by newer and older operating systems.
  3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard drive capacity to confirm it’s the correct hard drive) and then right-click in the section that says “Unallocated” and select “New Partition”.

Specifications

Host Interface USB 3.0

External Connectors

| 1x 15 pin SATA Power Female 1x 7 pin SATA Data Male

1x USB 3.0 type Micro-B female

Maximum Data Transfer Rate| USB 3.0: 5 Gbit/s

Compatible Operating System

| Windows 2000/XP/Server 2003/Vista/ Server 2008 R2/7/8 (32/64-bit), Mac OS 9/10, Linux

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to providing industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two-year warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.

StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions.

We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.

Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.

StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom, and Taiwan servicing a worldwide market.

Contact Information

  • For the most up-to-date information, please visit: www.startech.com
  • Manual Revision: 05/28/2013

Frequently Asked Questions

What is the maximum supported capacity for the hard drive or SSD that I can use with this enclosure?

The enclosure has been tested with hard drives up to 1TB with a 5400 RPM speed. While this is the tested capacity, it should be compatible with other capacities as well, as long as they are 2.5-inch SATA drives within the supported height range.

Can I use this enclosure to clone my existing hard drive or SSD?

Yes, you can use this enclosure for drive cloning or data migration. You would need appropriate software and tools to perform the cloning process.

Does the enclosure support hot-swapping of drives?

Hot-swapping is not recommended for this enclosure. It's advisable to power down and disconnect the enclosure before removing or replacing the drive to ensure data safety.

Can I use this enclosure with gaming consoles like Xbox or PlayStation to expand storage?

This enclosure is primarily designed for use with computers and may not be compatible with gaming consoles. Gaming consoles often have specific storage requirements, so it's essential to check compatibility with your console's manufacturer.

Can I connect this enclosure to a USB hub for additional ports?

Yes, you can connect this enclosure to a USB hub to expand your available USB ports. However, keep in mind that the hub's performance may affect data transfer speeds.

Is there any encryption or security feature included with this enclosure?

This enclosure does not provide encryption or security features. It is a straightforward external storage solution. If you require encryption, you may need to encrypt the data on the drive itself or use encryption software.

What is the difference between USB 3.0 and USB 3.2 Gen 1 in terms of performance?

USB 3.0 and USB 3.2 Gen 1 are essentially the same and offer data transfer speeds of up to 5 Gbps. The term USB 3.2 Gen 1 is a newer naming convention used for USB 3.0 to avoid confusion with faster USB standards like USB 3.1 and USB 3.2 Gen 2.

Can I use this enclosure with my Chromebook running Google Chrome OS?

Yes, this enclosure is compatible with Google Chrome OS, making it suitable for Chromebook users who need additional external storage.

Can I use this enclosure with an SSD for faster data transfer speeds?

Yes, you can use this enclosure with a 2.5-inch SATA SSD for faster data transfer speeds compared to traditional HDDs. The enclosure supports both SSDs and HDDs.

Does the enclosure support TRIM for SSDs?

The enclosure itself does not provide TRIM support. TRIM is typically managed by the operating system. Ensure that your operating system supports TRIM for SSDs.

Can I use this enclosure for backup purposes?

Yes, this enclosure is suitable for creating backup solutions. You can use it to back up important data to an external storage device, providing an additional layer of data protection.

Is the enclosure compatible with 2.5-inch SATA SSDs and HDDs of various heights?

Yes, the enclosure is compatible with 2.5-inch SATA SSDs and HDDs of various heights, up to 9.5mm drive height.

Reference:StarTech S2510BPU33 Storage Drive Enclosure Instruction Manual- Device.Report

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

StarTech User Manuals

Related Manuals