adiding TBD-55 LED Solar Outdoor Lights User Manual

LED SOLAR SENSOR LIGHT
USER MANUAL
Model: TBD-56

TBD-55 LED Solar Outdoor Lights

INSTALLATION

Choose aplace where the solar panels can get enough sunlight toinstallit. The longer the solar panels are exposed to sunlight, the longer the product’s light lasts.

1. Depending on the width of the two holes on the base, drill two holes on the wall. Knocking the expansion plastic screw tube into the wall holes, and then twist the screw through the base into the wall holes. The bracket of the base should be upward.
2. Install the pivot arm to the back of the solar panel and light. And then install solar panels and light, please insert the pivot arm into the bracket on the base. When installing the light, please keep the sensor and water outlet of the light down.
3. Adjust the angle and tighten the knob screw.
4. Choose a place where can get enough sunlight to intall solar panel.
5. Connect the wire of the solar panel with the wire of the light, and then tighten the waterproof nut cap.
6. The default mode of the product is OFF mode. Before ntalling the light on the wall, please press the light’ s button to turn on the power for test and adjust the light modes.

| |
---|---|---
1. Bracket Upward. Fix the base o the wall.| 2. Install the adjustable pivot arm and insert it into the base’s bracket.| 3. Adjust the correct angle and tighten the knob screw.
| |
4. Choose the place that can get enough sunshine to install solar panel.| 5. Connect the solar panel and light.| 6. Press the button to turn on the power for test and adjust modes.

TWO INSTALLATION MODES

1. Solar panel and light are installed separately.
2. Embed the pivotarm on the back of the solar panelinto the bracket above the light.

THREE LIGHTING MODES

•  Mode 1: Strong Light Sensor Mode When it detects people coming, it automatically turns on the bright light. After people leave for 20 seconds, the lights automatically turn off.
• Mode 2: Dim Light Sensor Mode Dim lighting, always on. But when the sensor detects people coming, itturns on strong lightillumination. Then after 20 seconds of people leaving, it will return to dim lighting.
• Mode 3: Normal lighting Thelights are always onall night. LED Solar Sensor Light will automatically detect the external ambient brightness. When the brightnessis dark enough, the light mode you selected will be automatically turned on. When  the brightnessis bright enough, it will automatically turn off the light mode.

MODES CONTROL

(Note: The default mode of the product is OFF mode.)

1. Botton Control
   Click the button on the back of light, each press the button will change one mode. Mode setin cycle(Mode 1-Mode 2-Mode 3-OFF).

2. Remote Control
   Use the remote controller to select the mode you want. Before using the remote controller, you must activate the light by click the button on the back of light.

TIPS

1. Before installing and using the light for the first time, please make aninitial charge for it. Connect the solar paneland the light, keep iton OFF state, and charge it with direct sunlight for 1-2 days.

2. Thesolar panel must be installed outdoors. Direct sunlight is needed for the solar panel to charge the internal battery most efficiently and make it operate properly. In order to convert solarenergy into electricity most efficiently, please ensure that the solar panel is completely exposed to the sun without any occlusion objects, like trees, eaves and others.

3. The motion sensor is very sensitive to light. In order to get the best performance at night, please check that there have no other lights to interfere the motion sensor.

4. The motion sensor is the most sensitive when people or objects move parallel to the sensor head. If people or objects move directly on the sensor head, the motion sensor is the least sensitive.
   The detection range of LED solar sensor light is 6-8 M, and the illumination distanceis 8-10 M. The working environment temperature is -4~140 degrees Fahrenheit. Please do not install the light near heat sources such as air conditioners, vents or stove exhaust pipes, or in the direction of reflective objects and nearby light sources.

5. We recommend cleaning the solar sensor light regularly with a damp cloth to ensure optimal performance and battery charging.

PACKAGING

1. Solar Panel X1
2. LED Solar Sensor Light X1
3. Screw Pack X1
4. Remote Controller X1
5. Bases X2
6. User Manual X1
   (Before beginninginstallation of the product, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the product.)

SPECIFICATION

WARRANTY

This productis covered under a 1-year limited warranty. If you have any questions, please feel free to contact us.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>