adiding KZ-S3 Ultrasonic Cleaner User Manual
- May 15, 2024
- Adiding
Table of Contents
adiding KZ-S3 Ultrasonic Cleaner
Thank you for purchasing the ultrasonic cleaner. Please read these instructions carefully before using and retain them for future reference.
SAFETY PRECAUTIONS
Keep it away from children!
This device is not intended to use by individuals with restricted physical
sensory or metal capacities or those with lack of experience or knowledge,
include children, unless they are supervised by an individual who is
responsible for their safety or have received training in operating the
device.
Please read the following very carefully as failure to comply may invalidate your guarantee.
- DO NOT run the ultrasonic cleaner con ti nuously for more than one hour at a time, it would be damage the internal components.
- DO NOT operate it without fluid in the tank. Always ensure the fluid is no higher than the max mark, always ensure there is at least 1/2 solution.
- DO NOT drop any item into the tank, it may cause damage to the transducer. Always place the items gently into the tank and use the basket whenever possible.
- The more items you place in your cleaning bath the less efficient it will clean. It is not advised to overlap items. Always allow plenty of clear space between this items.
- Do keep the lid on during use. This will prevent splashes and reduce evaporation of the fluid.
- Never immerse the machine or power cord in water or other liquid.
- DO NOT touch the power plug with wet hands, especially when inserting or removing the plug.
- DO NOT touch the unit if the machine has fallen into water during operation, Remove the power plug from the socket first.
- DO NOT disassemble the machine, except by professionals.
- UNPLUG the power source while filling or emptying the tank.
- DO NOT spray water or liquid over the device and the control panel.
- DO NOT operate the cleaner without proper grounding.
- DO NOT place the device on a soft surface, where the vents could be blocked.
- Upon completion of the cleaning cycle, turn the heater knob off and isolate the machine from the electricaI supply.
- Take care when adding or removing items from the cleaning tanks as the fluid is Iikely to be hot and displaced fluid can damage the internal components. Any displaced fluid must be dried up immediately.
- In the event of failure/emergency, disconnect the mains supply by removing the plug from the mains socket.
ULTRASONIC PRINCIPLE
Ultrasonic cleaning is on based on the cavitation effect caused by high
frequency ultrasonic wave vibration signal in the fluid. Microscopic bubbles
are formed, and they implode violently causing the cavitation which create an
intense scrubbing action on the surface of the item being cleaned. The bubbles
are small enough to penetrate microscopic crevices, cleaning them thoroughly
and consistently.
Ultrasonic cleaning is extremely effective at removing dirt and grime which
would normally require tedious manual cleaning by hand. It has been used to
clean a wide variety of instruments and mechanical parts such as “like new”
condition without damage carburetors, returning them to almost to delicate
parts.
PREPARATION
- Carefully unpack the cleaner and remove all traces of packing materials from it. Visually inspect the cleaner for any parts that may have become loose or damaged during transit.
- Place the cleaner on a flat, clean surface where the cooling fans will receive adequate ventilation and ensure all controls are set to off. Also ensure the drain tap is in the closed position.
- Ensure the power lead is securely plugged into the cleaner and that no part of the lead is likely to come into contact with moisture.
- Carefully fill at least 1/2 of the tank with a solvent solution. For demanding cleaning we recommend a small amount of washing up liquid, this will help increase the cleaning performance. The cleaner is now ready for use.
Attention
- While the machine is working normally, ultrasonic and tank gives a well-proportioned sound, and no shudder on the surface of the water, but there is spray made by the tiny bubbles. If there are discontinuous surges, please add or release a little of washing solution in the tank, stopping the surges is better for the objects cleaning.
- On the condition of making sure the cleaning object is cleaned, please run the machine intermittently as far as possible (not more than 30 mins), for long-time running will cause temperature increment of the case.
APPLICATION
Our mechanical heating ultrasonic cleaner is professional for
- Turbochargers
- Vehicle differentials
- Engine cylinder heads
- Coins and other collectibles
- Golf clubs & grips & golf balls
- Diesel injection pumps
- PCB Boards etc
- Watchstraps
- Make-up cases
- Engine/Model parts
- Horse bits&stirrups &horse brasses
- Knives, bayonets and other military
- Jewelry especially gold, silver & platinum
- Motorcycle radiators
- Surgical equipment
- Bicycle derailleurs
- Milking parlour equipment
- Printer heads and toner cartridges
- Motorcycle engine crank cases
- Gun and gun components
- Tattoo needles
- Electrical components
- Toothbrushes & Dentures
Ultrasonic cleaning is not recommended for the following gemstones: Opal, Pearl, Emerald, Tanzanite, Malachite, Turquoise, Lapis and Coral.
PANEL AND FUNCTION DISPLAY
CLEANING AND MAINTENANCE
- The item should be immersed well into the water (not exceed the “MAX” mark)
- Warm water (never hot or boiling) and a small amount of washing up liquid will help increase the cleaning performance.
- Make sure there is good space around each part that you put in the tank, the more items that you place in the tank, the efficiency will be lower. It is not advised to overlap items, if lay items one on top of the other, then the system does not work as expected.
- Basket use: Do not put items directly into the bottom of the tank, better cleaning effect with a suitable basket. A metal basket absorbs less ultrasonic energy at about 8%.
- Temperature: The higher temperature the better cleaning effect. However, when temperature exceed 700C-800C, cleaning effect will be affect, the best temperature we suggest is 400C-600C.
SPECIFICATION
WARRANTY
We are responsible for each product we sell and committed to providing you the most wonderful shopping experience. Please kindly refer to our warranty policy below: Within 1 year of purchase, you can feel free to contact us by E-mail for proper service, if it is found to be defective under normal use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>