RYOBI R18PD5 ONE+ Compact Brushless Combi Drill User Manual
- June 12, 2024
- RYOBI
Table of Contents
R18PD5
Important! It is essential that you read the instructions in this manual
before assembling, maintaining and operating the product.
Subject to technical modification
Safety, performance, and dependability have been given top priority in the
design of your percussion drill.
INTENDED USE
The percussion drill is intended to be used only by adults who have read and
understood the instructions and warnings in this manual, and can be considered
responsible for their actions.
The product is intended for drilling into various materials, including wood,
metal, and plastics using a drill bit having a shank diameter of less than 13
mm. The product can be used to drive and remove screws and bolts using an
appropriate bit.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the in a hazardous
situation.
WARNING! Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
- Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
- Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring. Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS
- Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
- Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
- Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.
ADDITIONAL SAFETY WARNINGS
-
Clamp workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
-
Dust created by operating the product can cause respiratory injury. Wear appropriate dust control mask with filters suitable for protecting against particles from the material being worked on.
-
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.
-
Switch off the product immediately if the bit stalls. Do not switch on the product again while the bit is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the bit stalled and rectify this, paying heed to the safety instructions. The possible causes may be:
— it is tilted in the workpiece
— it has pierced the workpiece
— the product is overloaded -
Ambient temperature range for tool during operation is between 0°C and 40°C.
-
Ambient temperature range for tool storage is between 0°C and 40°C.
-
The recommended ambient temperature range for the charging system during charging is between 10°C and 38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
- To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
- Ambient temperature range for battery during use is between 0°C and 40°C.
- Ambient temperature range for battery storage is between 0°C and 20°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and
regulations.
Follow all special requirements on packaging and labelling when transporting
batteries by a third party. Ensure that no batteries can come in contact with
other batteries or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or tape. Do not
transport batteries that are cracked or leaking. Check with the forwarding
company for further advice.
KNOW YOUR PRODUCT
See page 69.
- Gear selector (drill or hammer mode only)
- Mode selector
- Keyless chuck
- Direction of rotation selector
- Variable speed switch trigger
- Handle, insulated gripping surface
- LED light
- Bit storage
- Battery port
- Screw driver bit
- Operator’s manual
- Battery pack
- Charger
ELECTRONIC PROTECTION
This drill includes advanced electronics designed to protect the tool, battery
and user. The LED work light will flash if any of these protections are
triggered.
The drill will shut down and the LED will flash 4 times in a case of overload,
this resets as soon as the trigger is released. It is recommended that you
change to speed 1 and/or drill a smaller pilot hole in order to complete your
application.
The drill will shut down and the LED will flash 6 times in a case of low
voltage. It is recommended that you recharge your battery to complete your
application.
The drill will shut down and the LED will flash 10 times in a case of
excessive internal temperature. The drill cannot resume working until it cools
down to a normal temperature.
MAINTENANCE
- The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.
- When servicing, use only original manufacturer’s replacement parts, accessories and attachments. Use of any other parts may create a hazard or cause product damage.
- Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
- Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
- For greater safety and reliability, all repairs should be performed by an authorised service centre.
E-TORQUE CONTROL
e-Torque control is a technology which automatically drives most screws flush.
When in the auto screw driving mode the drill will stop once the screw is
flush. If a deeper screw is required, continue depressing the trigger. The
drill will begin small rotations at a manageable speed. Release the trigger
once the desired depth is achieved.
When using e-Torque control it is important to ensure the screw bit is
correctly seated and does not slip from the screw head. If the screw bit is
incorrectly fitted the drill may stop early to prevent damage to the screw
head or bit. If this occurs, realign the bit with the screw head and depress
the trigger again.
NOTE: e-Torque control works with most materials and applications but may
not operate with certain materials or screws, e.g., machine screws into metal
or plastic threads.
SYMBOLS ON THE PRODUCT
| Safety alert
---|---
| European Conformity Mark
| British Conformity Mark
| Ukraine Conformity Mark
**| EurAsian Conformity Mark
V| Volts
**| Direct current
min -¹| Revolutions or reciprocations per minute
∅| Chuck capacity
No| No-load speed
| Please read the instructions carefully
before operating the product.
| Drilling without impact
| Auto screw driving mode
| Percussion Drill
| be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
SYMBOLS IN THIS MANUAL
| Note
---|---
| Parts or accessories sold separately
| Speed, minimum
| Speed, maximum
Product specifications
18V Brushless Percussion Drill Model Voltage Chuck Switch – Variable speed
No-load speed (Drill mode) LO Speed HI Speed No load speed (Percussion drill
mode) LO Speed HI Speed Maximum torque Maximum drilling capacity, in wood
Maximum drilling capacity, in metal Maximum drilling capacity, in masonry
Weight – excluding battery pack Weight – according to EPTA Procedure 01/2014
Product specifications Measured sound values determined according to EN 62841:
A-weighted sound pressure level Uncertainty K A-weighted sound power level
Uncertainty K Wear ear protectors. The vibration total values (triaxial vector
sum) determined according to EN 62841: Impact drilling into concrete
Uncertainty K Drilling into metal Uncertainty K Screwdriving without impact
Uncertainty K
Battery and charger
Compatible battery pack (not included) Lithium-Ion Compatible charger(not
included)
WARNING
The declared vibration total values and the declared noise emission values
given in this instruction manual have been measured in accordance with a
standardised test and may be used to compare one tool with another. They may
be used for a preliminary assessment of exposure.
The declared vibration and noise emission values represent the main
applications of the tool. However, if the tool is used for different
applications, used with different accessories, or poorly maintained, the
vibration and noise emission may differ.
These conditions may significantly increase the exposure levels over the total
working period. An estimation of the level of exposure to vibration and noise
should take into account the times when the tool is turned off or when it is
running idle. These conditions may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration and noise, such as maintaining the tool and the accessories,
keeping the hands warm (in case of vibration), and organising work patterns.
RYOBI® WARRANTY APPLICATION CONDITIONS
In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.
-
The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
-
There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly- acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
-
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
– any damage to the product that is the result of improper or lack of maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any product not displaying the CE approval mark on the rating plate
– any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
– normal wear and tear spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– Power tool accessories provided with the tool or purchased separately, including but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide, etc.
– Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc. -
For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected
-
This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE
Any request or issue with the product can be addressed to your local
authorised service centres (visit
www.ryobitools.eu ) or directly to: Techtronic
Industries GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state
the serial number and product type printed on the label.
EC DECLARATION OF CONFORMITY
18V Brushless Percussion Drill
Brand: RYOBI | Model number¹
1 Serial number range²
We declare as the manufacturer under our sole responsibility that the product
mentioned below fulfills all the relevant provisions of the following European
Directives, European Regulations and harmonised standards Authorised to
compile the technical file:⁴
DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product
mentioned below
18V Brushless percussion drill Brand: RYOBI
Model number: R18PD5
Serial number range: 47561101000001 – 47561101999999
fulfills all the relevant provisions of the following Regulations: S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as
amended) and that the following designated standards have been used:
BS EN 55014-1:2017+A11:2020, BS EN 55014-2:2015, BS EN 62841-1:2015, BS EN
62841-2-1:2018+A11:2019, BS EN IEC 63000:2018
Todd Chipner
Vice President, Quality – Ryobi Asia
Winnenden, Nov. 12, 2020
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
RYOBI is a trade mark of Ryobi Limited, and is used under license.
Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK
961075680-01
Documents / Resources
|
RYOBI R18PD5 ONE+ Compact Brushless Combi
Drill
[pdf] User Manual
R18PD5 ONE Compact Brushless Combi Drill, R18PD5, ONE Compact Brushless Combi
Drill, Brushless Combi Drill, Combi Drill
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>