Abestorm DecDust 1100IG Restoration and Drying Equipment User Manual
- June 9, 2024
- ABESTORM
Table of Contents
Abestorm DecDust 1100IG Restoration and Drying Equipment
INTRODUCTION
DecDust 1100/ll00IG is small in size and lightweight. The machine is equipped with two lightweight filtering devices to avoid the unnecessary increase in weight and volume increase. It effectively enhanced the air purification capability that allows to the filtration of small particles such as dust, sawdust, and many more.
WARNING!
Please note that the dust collector can only be used with Abestorm approved accessories. Using unauthorized accessories or making changes to the machine may invalidate your warranty. Please contact us for more details.
To Avoid Accidents:
- The power cord of the machine must be plugged into a grounded socket.
- The power supply of the machine must not be higher than the specified power supply.
- The machine should not be installed outdoors or in places that may be eroded by Rain Water to avoid damaging the electrical components and Fire.
- Do not run the machine without a filter installed.
- If hooks are installed on the ceiling, the load bearing capacity of the ceiling must be greater than 1101bs.
- If the dust collector is to be installed on the ceiling, the distance between the bottom of the dust collector and the ground must be greater than 7 ft.
- Installation requires two people.
IDENTIFICATION
Congratulations on purchasing a Abestorm dust collector. For your convenience in submitting a warranty claim in the future, be sure to note the serial and the date of purchase below.
HOW IT WORKS
- Connect the dust collector to a standard 115V/60Hz outlet.
- Refrain from moving the unit during operation.
- Keep both air inlet and outlet away from the wall or any obstructions for at least 2 ft.
- This product can only filter dust particles above lum.
SPECIFICATION
DecDust1100
| ****
DecDust11 00IG
---|---
Power
| ****
110-120,60Hz, 1.8A
| ****
Power
| ****
110-120,60Hz, 1.8A
Control mode| ****
Manual/ remote control
| Control mode| ****
Manual/ remote control
Wind speed| ****
LO/MID/HI
Low/Middle/High
| Wind speed| ****
LO/MID/HI
Low/Middle/High
Timing
| ****
lH, 2H, 3H 4H, SH, 6H
| ****
Timing
| ****
lH, 2H, 3H 4H, SH, 6H
Noise
| ****
(HI) 66dB
| ****
Noise
| ****
(HI) 66dB
Net weight
| ****
33lbs
| ****
Net weight
| ****
33lbs
Size
| ****
24.6 X 20.1 X 10.6 in
33lbs
| ****
Size
| ****
24.6 X 20.1 X 10.6 in
33lbs
Ion Fuction
| ****
No
| ****
Ion Fuction
| ****
Yes
KEY FEATURES
INSTRUCTION
Power key:
Turn on and off air filtration equipment Click the control panel “ON/OFF”
/remote control”ON/OFF” .The machine will make a “drip” sound, the environment
prompt light will be on, and the display screen will display the PM a number
of the environment.
Wind speed key:
Control the wind speed of Low, Middle, and High. Each time it is operated, the
light of the control panel will switch to one of the wind speed gears, and the
light represents the wind speed of the current gear.
Timing:
Control the working hours of the machine:
Operate the remote control “TIME” button, The display screen will display a
timing number. , Press the “TIME” button once, and display the content once
(OH, lH, 2H, 3H, 4H, SH, 6H). OH stands for an indefinite time, (lH, 2H, 3H,
4H, SH, 6H} the number,is the running time of the machine, and H represents
the hour. After setting the working hours, the display content automatically
switches to the environment PM to detect the content value, which means that
the command takes effect and starts the countdown work.
Ionizer switch button:
Description: This button is only used on the remote control, which is a
general accessory. The low-end version does not have this feature, so you need
to pay attention to the version model when you buy it. Operate the “IONIZER”
button of the remote control, the ionizer switch light on the control panel is
on, the ion function starts, and operates again, the ionizer switch light is
off and the ion is off.
Rise Drop:
Description: this button function is only used on the remote control. Operate
the up arrow and down arrow of the remote control. Set the desired PM number.
The setting number can be switched within CO- 80 0, and the display number
rises or decreases by SO perspiration. The minimum CO number is set to rep
represent the continuous operation of the machine and is not affected by the
sensor. When the PM number in the display screen is higher than the set
number, the machine is running.
Environmental warning lamp
Color| Green| Yellow| Red
Air Quality
|
Excellent
|
Good
|
Bad
Note: please pay attention to the air quality of the room when it is shown in red.
HOW TO INSTALL A DUST COLLECTOR
Installation mode 1
- Fix the hook as shown in the picture to 4 holes at the top of the machine with an M4 nut. The M4 nut needs to be tightened to prevent the hook from rotating and falling off.
- Fasten the horn hook to the ceiling.
- Two people are required for this installation. One(l) person to pick up the dust collector and the other to connect the end of the chain to the machine hook.
- Due to the impact of the machine itself and the environment, there will be installation imbalance, and the number of sections of the chain hook can be used to adjust the machine balance.
Installation mode 2
- Remove the four M4 screws from the top of the machine, install the pendant as shown in the picture, and fix the M4 screws just now.
- 0ne man picked up the dust collector and the other screwed the machine to the wall.
HOW TO REPLACE THE FILTER-
- Turn off the machine before replacement.
- Loosen the buckles on the side of the machine.
- Remove the filter.
- Install a new filter.
- Pay attention to the sequence of filters
MAINTENANCE AND CLEANING
- Disconnect the power supply before cleaning.
- 0pen the cover next to the button on the machine control panel.
- Use a brush to dust the lid. Then put the lid on and plug it in
INSPECTION AND TROUBLESHOOTING
- The display shows “000”, the motor stops working, and the PM2.5 indicator light shows red, which means a problem with the PM sensor. Maintenance and cleaning are required.
- If the machine is short-circuited and there is a power outage at home, the overload protector will cut off the circuit to protect the machine
POWER-OFF PROTECTION TREATMENT
- Unplug the machine.
- Press the overload protector button back to its original position by hand.
- Plug in the power supply and start-up.
LIMITED WARRANTY
The limited warranty is applicable to the Original purchaser only, from the date of purchase. It should be subject to the terms and conditions listed in this limited warranty file
WARRANTY PERIOD
Warranty becomes effective from the date of original purchase and will last
for one (2) year. This limited warranty is not transferable. It is only valid
for the original purchaser.
Warranty department:
- Damage caused by the owner when attempting to fix or alter the product by himself or herself.
- Damage caused by misuse, abuse, neglect, alterations or unauthorized repair.
- Natural depreciation.
How to request warranty services?
To obtain the benefit of this warranty, please leave your message online
(www.abestorm.com), or send an email to
sales@abestorm.com. Our customer service will address
your issue between Mon-Fri 7:00AM to 4:00 PM PST.
Abestorm Warranty Steps:
- Upon receiving this item, visit www.abestorm.com and fill out the warranty registration form. The order number is required to submit a warranty claim.
- To request warranty service, contact sales@abestorm.com.
- After receiving the warranty service request, our customer support team will investigate the issue. Here, will be determined if a Return authorization is necessary.
- If the damage to the machine is proven to be one of the warranty exclusions (Page 10), Abestorm will not be responsible for all the associated repair and shipping costs.
- The eligibility of a replacement unit will also be voided.
- If the damaged unit that can no longer be fixed is within the warranty period, Abestorm will handle all the cost to send a brand-new replacement unit.
- When the unit is repaired or replaced, the original warranty period carries over to the repaired or new unit. No warranty extensions will be offered.
Warranty Exclusions
- Acts of Nature- including but not limited to:
- Flooding
- Fire
- Water damage
- Hurricane/storm damage
- IMPROPER USAGE- Including but not limited to:
- Misuse, abuse, or tampering whether intentional or accidental
- Improper installation
- Improper voltage
- Improper maintenance
- Failure to follow instructions
- Corrosion
- Freezing
- Any additional costs due to changes in laws or building codes
- Freight charges
- Any costs due to lost profit or delay
- Damage to property
- Cause beyond control
- Consumable parts, including but not limited to:
- Filters
- Batteries
- Power cords
- Valves
- Switches
- Rubber parts
- Direct, indirect, collateral or inconsequential damages of any kind
THE WARRANTIES AND LIABILITIES SET FORTH ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, IN LAW OR IN FACT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE. Abestorm total liability, regardless of the nature of the claim shall not exceed the original purchase price of the product. If a product or component is replaced while under warranty, the applicable warranty period shall not be extended beyond the original warranty time period. The foregoing shall constitute the total liability of seller in the case of defective performance of all or any of the equipment or services provided to the Buyer. Buyer agrees to accept and hereby accepts the foregoing as the sole and exclusive remedy for any breach or alleged breach of warranty by Seller. Any dishonesty or fraud in connection with the Abestorm warranty thoroughly voids all warranty policies. Abestorm expressly reserves the right to pursue legal action in the event of dishonesty, fraud, or attempted fraud.
Wiring Diagram
Documents / Resources
|
Abestorm DecDust 1100IG Restoration and Drying
Equipment
[pdf] User Manual
DecDust 1100, DecDust 1100IG, DecDust 1100IG Restoration and Drying Equipment,
DecDust 1100IG, Restoration and Drying Equipment, Drying Equipment
---|---