GLOBALO TZ 1.1 External Turbine Instruction Manual

GLOBALO TZ 1.1 External Turbine

Dear Customers,

• Thank you for choosing our brand. We hope that you will be satisfied with our product. Every product that leaves our production plant is carefully inspected for quality and safety.
• Before installation and use of the hood, you are kindly requested to read this manual carefully and follow the safety instructions. We also recommend that you keep the manual in an easily accessible place so that you can consult it at any time.
• GLOBALO team
• To ensure the maximum safety of the device, the most important information has been marked with the following symbol:
• THE CAUTION SYMBOL INDICATES POSSIBLE DANGERS WHEN USING THE HOOD. FOR YOUR SAFETY, CAREFULLY FOLLOW THE INSTRUCTIONS INDICATED BY THIS SYMBOL!

GENERAL INFORMATION ON SAFETY AND INSTALLATION

• Keep this user manual for future reference.
• Please read this user manual, which contains detailed information regarding installation, assembly, and maintenance of the turbine.
• The turbine may differ in terms of appearance from the one in the drawings shown in this manual, but recommendations regarding maintenance and assembly remain unchanged.
• Do not make electrical or mechanical changes to the turbine.
• Do not connect the device to the power supply before completing the installation process.
• Use protective gloves for all installation and maintenance operations.
• Do not use sources of open fire underneath the hood.
• If you have other non-electric appliances in the house (e.g. liquid fuel cookers, flow-through heaters, water heaters) make sure that there is sufficient air supply in the room.
• Do not pull on the power cord to disconnect the plug from the socket.
• The power cord must not be in contact with any hot surfaces.
• Do not switch on the device if the power cord is damaged.
• A damaged power cord may only be replaced by the manufacturer, repair center, or a qualified specialist.
• Children at least 8 years old, persons with physical or mental disabilities, and persons with a lack of knowledge or experience in using the device may use it only under supervision or after being properly instructed in terms of safe operation.
• Children should not be allowed to play with the device.
• Children are not allowed to clean the device without supervision.

CAUTION!

• EASILY ACCESSIBLE PARTS MAY BECOME HOT WHEN THE COOKER IS USED. USING SCREWS OR FASTENERS OTHER THAN APPROVED IN THE MANUAL MAY RESULT IN ELECTRIC SHOCK.

ENVIRONMENTAL PROTECTION

• The product is made of high-quality recyclable materials.
• The symbol of a crossed-out wheelie bin on the product (Fig. 1) indicates that the end users should segregate the product from other waste at end-of-life, under the provisions of Directive 2012/19/EU of the European Parliament and of the
• Council. If the symbol shown in Fig. 2 is used, it means that the product contains batteries, which the end users should segregate from other waste at end-of-life, under the provisions of Directive 2006/66/EU of the European Parliament and of the Council.
• The mentioned marking means that end-of-life electrical and electronic equipment and batteries (if any) must not be disposed of with other household waste. The user is obliged to return used electrical and electronic equipment and batteries (if any) to special collection points for such items. Operators of collection facilities, including local collection points, shops, and municipal units must have in place an appropriate system enabling the users to return such equipment and batteries.
• Proper disposal of waste equipment and batteries prevents the harmful impact of hazardous components of these items on human health and the environment, resulting from improper storage and handling of such equipment and batteries. Individual households play an important role in ensuring reuse and recovery, including recycling, waste equipment, helping to preserve a clean environment, which is our common good. It is also households that are the largest consumer of small appliances, hence rational management of waste improves the efficiency of secondary raw materials recovery. Improper disposal of this product may result in penalties, imposed under national legislation.

TECHNICAL SPECIFICATION

• Supply Voltage:
• Frequency:
• Motor power:
• Number of speed levels:
• Outlet diameter:

TZ 1.1

220 – 240V

~50 Hz

215 W
4

Ø15 cm

INSTALLATION AND OPERATION

• The range hood is designed for fume and smoke extraction during food preparation.

CAUTION!

• USE THE SHORTEST POSSIBLE EXHAUST DUCT.
• USE AN EXHAUST DUCT WITH A SMOOTH INTERNAL SURFACE (SPIRO DUCTS ARE NOT RECOMMENDED).
• ANY BENDING OF THE DUCT SHOULD BE LIMITED TO MINIMUM (THE ANGLES SHOULD NOT EXCEED 90°).
• COMBINING DUCTS WITH DIFFERENT CROSS-SECTIONS IS NOT RECOMMENDED (E.G. Ø15 CM WITH Ø12 CM).
• ENSURE THAT THE SIZE OF THE SUCTION OPENING IS AT LEAST AS BIG AS THE SIZE OF THE AIR EXHAUST. THIS WILL PREVENT NEGATIVE PRESSURE AND ENSURE PROPER FUNCTIONING OF THE HOOD.
• IF THERE ARE ANY OPEN-FLAME APPLIANCES IN THE ROOM (E.G.: SOLID AND LIQUID FUEL COOKERS, FIREPLACES, HEATERS, ETC.). MAKE SURE THERE IS AN ADEQUATE SUPPLY OF FRESH AIR.

PREPARATION BEFORE TURBINE INSTALLATION

• Check whether the dimensions of the purchased product are adapted to the selected destination.
• Disconnect and remove (if possible) devices located in the turbine installation area to facilitate access to the place where it is to be installed. If this is not possible, secure elements located near the work being performed.
• Make sure there are no lines of electric and plumbing installations in places where holes will be drilled.
• Prepare the following tools: tape measure, pencil, drill/driver, Ø3 mm drill bit, screwdriver, and level.
• CAUTION! BE CAREFUL NOT TO SCRATCH THE TURBINE.

TZ

INSTALLATION OF THE EXTERNAL TURBINE

It is possible to redirect the air outlet outside the building:

• A – Air outlet outside the building
• B – Elevation turbine
• C – Intake pipe Ø150mm
• D – Intake pipe Ø150mm
• E – Hood with control
• CAUTION: The turbine is designed to be mounted outside the building. The turbine can only be mounted on vertical walls of the building facade.

1. Components of an external turbine.
2. Preparing the external turbine for installation.
3. Installation of the turbine body on the building facade.
4. Electrical connection of the external turbine and installation of the cover.
5. Preparation of the hood for installation of the intake pipe and turbine power supply.

• Case 1 The hood is adapted to be connected to a turbine. The hood does not contain a motor and contains a power socket on the housing.
• CAUTION! DEPENDING ON THE HOOD MODEL, THE ACCESSORY SET MAY ALSO INCLUDE A CONNECTOR FOR THE TURBINE POWER CABLE AND A SOCKET IN THE HOOD BODY.

Case 2 Standard hood with a motor.

To connect to the turbine:

1. Remove the motor from the hood and unplug the power cord.
2. Screw on the input adapter included in the set, passing the adapter cable through it.
3. Connect the adapter cable with the previously disconnected engine power cable and turbine power cable.

POWER SUPPLY CONNECTION

• The supply voltage must correspond to the voltage indicated on the identification plate placed inside the hood. If the hood is equipped with a plug, insert it in an accessible socket compliant with the applicable regulations. If the hood is not equipped with a plug, the installation should be carried out by a certified specialist (e.g. an electrician).

CLEANING AND MAINTENANCE

• Before performing any maintenance or cleaning of the device, disconnect the power supply. Use mild cleaning agents for cleaning. Do not use abrasive cleaners.

IN CASE OF PROBLEMS

The turbine does not function at all:

• Check whether the fuse in the domestic installation is not pulled out.
• Check if the thermal cutout of the motor has not been activated due to high temperature. If this is the case, switch off the device and wait for about 20 – 30 minutes until the temperature returns to normal; then switch the hood on again.
• Make sure that the turbine power cord plug is properly connected to the hood.
• Remove the hood’s mains plug to restart the device. Wait approximately 15-20 seconds, then insert the plug into the socket again. Alternatively, you can also turn off the relevant fuse for the above-mentioned time and then turn it on again.

Insufficient efficiency / noisy operation:

• Check whether the cross-section of the ventilation duct is sufficient and whether it does not have too many bends and sharp angles.
• Check if the return flap (if optionally installed) is not jammed in the ventilation duct.
• If the ventilation duct is equipped with a swinging grille, remove it.
• Make sure that the metal filters are clean.
• Check whether the amount of air extracted from the kitchen is balanced by sufficient fresh air supply (to prevent negative pressure).
• Check whether the ventilation chimney is not obstructed.
• Excessively low atmospheric pressure may reduce the performance of the hood. Verify the functioning of the hood again on another day.

REDUCING THE IMPACT OF COOKING ON THE ENVIRONMENT

• To reduce energy consumption, cover pots and pans with lids while cooking.
• Keep the aluminum filters clean (the recommended cleaning schedule for the filter is at least once every 35 hours).
• Keep the ventilation ducts unobstructed.
• Always set the turbine speed during cooking to the minimum required level, allowing for fume extraction at the current cooking intensity.

SERVICE AND MAINTENANCE

• If, despite our strict quality control, you find any irregularities in the operation and functioning of the purchased device, please contact our service department to receive professional assistance from our team.
• The service support is available Monday to Friday from 9.00 am to 5.00 pm at +48 13 49 27 560 extension: 3 and +48 609 055 660 or by email at: serwis@globalo.pl.
• Before connecting the service, please take down the following details of your device:
• Type: ___
• Seria-Nr: ___
• You can find this information on the identification plate. The plate is located inside the turbine and is visible after removing the metal filters.
• The identification plate shown in the figure above is only an example. The data may differ for other models.
• To request a hood repair, you can use the form available at www.globalo.pl/serwis/.

TROUBLESHOOTING

When the hood is operating, a flashing „F” appears on the display*.

The display only shows the „-.” sign (minus and dot in the lower right corner), and the hood does not start when switched on*.

| After 35 hours of operation, the display indicates that the anti-grease filter needs to be cleaned or replaced. The touch panel is locked (this is a function used to facilitate cleaning of the hood).| Press and hold down for approx. 6s the „-” button on the panel. Clean the filter or replace it with a new one. To deactivate the lock, press and hold the on/off sign for approx. 10s.
No sign appears on the display, the hood does not respond to the buttons*.

The display shows the sign of one of the speed levels and the hood does not react to the buttons*.

| **** The control panel may be frozen.

The control panel may be frozen.

| Disconnect the hood from the power supply for approx. 15 seconds and then switch it on again.

Disconnect the hood from the power supply for approx. 15 seconds and then switch it on again.

The hood turbine switches off after 15 minutes. of operation and the display blinks with, for instance, „1” (the number of the current speed level and a dot in the lower right corner of the display*.

Number „4” on the display is blinking, and after 5 min. the speed level changes to 3*.

| The automatic timer of the control panel has been activated.

The hood is equipped with a turbo mode, which automatically changes to level 3 after 5 minutes of operation to save energy.

| To deactivate the timer, press the plus sign for about 10 seconds or switch off the device. ****

The turbo mode should only be used for intensive cooking.

The hood can only be operated using the control panel, it does not react to the remote control*.| The battery in the remote control is flat or the remote is too far from the device.| Replace the battery.
Low suction efficiency.

One or more light bulbs are not lit.

| The filters may be dirty.

Burnt halogen or LED bulb.

| Wash or replace the anti-grease filter. Replace the carbon filter (if any).

Replace the bulb under the user manual.

The hood generates excessive noise and vibration.| The reason may be an incorrect installation of the hood to the wall or kitchen cabinet. Not all of the screws required were screwed in, or the screws were not tightened enough, leaving clearance.| The hood must be fixed to the wall or cabinet using the number of screws indicated by the manufacturer. After adjusting the position of the hood vertically and horizontally, tighten all the mounting screws.

applies to range hoods with touch control

• If after following the above-mentioned guidelines the problem is still not solved, contact an authorized household appliance repair service. Do not try to repair the hood yourself. A list of authorized repair centers is provided on the warranty card and on the website.

WARRANTY

• Within 2 years from the date of purchase of the product, GLOBALO undertakes to cover all repair costs for faults that are caused by manufacturing defects.
• The warranty does not cover burnt bulbs, fuses, and filters, as well as any damage due to faulty installation and ventilation systems.

In addition, the warranty does not apply in the following cases:

• Application in the catering industry.
• Application for any other purposes than household use.
• Use of the device not under the operating instructions and its intended purpose.
• Circumstances beyond the control of the manufacturer, including, without limitation: uncontrolled power surges, flooding, and obstruction of the ventilation duct.
• Apparent mechanical damage after the installation of the device.

CAUTION!

• ANY PRODUCT WITH MECHANICAL DAMAGE, WHICH HAS NONETHELESS BEEN INSTALLED, WILL NOT BE REPLACED! BEFORE INSTALLATION OF THE DEVICE, UNPACK IT AND CAREFULLY INSPECT IT FOR ANY MISSING COMPONENTS OR DAMAGE. ANY VISIBLE EXTERNAL DAMAGE CLAIMED AFTER INSTALLATION IS EXCLUDED FROM THE WARRANTY.
• GLOBALS MAX SHALL NOT BE HELD LIABLE FOR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY PERSONS, ANIMALS OR OTHER OBJECTS AS A RESULT OF NON-COMPLIANCE WITH THE INSTRUCTIONS IN THIS MANUAL, IN PARTICULAR THOSE CONCERNING INSTALLATION, OPERATION AND MAINTENANCE OF THE DEVICE!

Central Firmy

• GLOBALO
• ul. Maków 10
• 38-500 Sanok
• Polska / Poland / Polen
• Tel.: +48 13 49 27 560
• www.globalo.pl
• e-mail: biuro@globalo.pl
• Serwis / Service / Kundendienst: Tel.: +48 13 49 27 560 wew. 3 Kom.: +48 609 055 660
• e-mail:serwis@globalo.pl
• www.globalo.pl/serwis/
• Ver. 1 / Copyright ©

Documents / Resources

| GLOBALO TZ 1.1 External Turbine [pdf] Instruction Manual
TZ 1.1 External Turbine, TZ 1.1, External Turbine, Turbine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>