FTDR3 Seaview Top Down Risers Instruction Manual
- June 14, 2024
- SEAVIEW
Table of Contents
FTDR3 Seaview Top Down Risers
Product Information
- Specifications:
- Model: Seaview Top-Down Risers
- Compatible Models: FTDR3, FTDR4, FTDR500
- Installation Instructions
- Mark all the holes to drill, and then drill.
- Use a hole saw to cut a hole for the center cable.
- Bolt the camera to the Top Down Riser using the six bolts and washers.
- Note: When mounting the Sionyx Nightwave, you will need to drill the cable hole in the FTDR3. You will also need to apply marine sealant in and around the slotted hole to keep water out.
- Apply marine adhesive sealant to the rubber gasket and underside of the Top Down Riser.
- Secure the Top Down Riser to the surface with your hardware. Be sure not to exceed 20-inch pounds. Use the six provided black nylon shoulder washers for the FTDR500.
- Optional Accessories
- You may consider using a Seaview Cable Gland for routing the cables through the mounting surface.
- Tools Needed
- Sudbury Elastomeric Marine Sealant is recommended. To purchase call 800-655-7922 or visit www.seaviewglobal.com.
- Optional Accessories
- Call 800-655-7922 or visit www.seaviewglobal.com for available accessories.
- FAQ
- Q: Where can I find the most up-to-date instructions and videos?
- A: You can find the most up-to-date instructions and videos on our website: www.seaviewglobal.com.
NOTE
- It is strongly advised that all installations are carried out by an authorized installer who possesses the necessary expertise and experience in marine equipment installation.
- Furthermore, prior to the final installation process, we recommend performing a dry fit assembly of all components.
- This entails fitting the components in their designated positions on the boat without permanently affixing them.
- This step allows for careful assessment of compatibility, alignment, and any potential adjustments that may be required before proceeding with the actual installation.
PARTS INCLUDED
- X1
- (FTDR3GSK)
- (FTDR4IGSK – used w/FTDR4 & FTDR500 only)
- X1
- (FTDR3P)
- (FTDR4P)
- (FTDR500P)
TOOLS NEEDED
- Sudbury Elastomeric
- Marine Sealant is recommended.
- To purchase call 800-655-7922 or visit www.seaviewglobal.com.
HOW TO USE
- Mark all the holes to drill, and then drill.
- Use a hole saw to cut a hole for the center cable.
- Bolt the camera to the Top Down Riser using the six bolts and washers.
- 3A Note, when mounting the Sionyx Nightwave you will need to drill the cable hole in the FTDR3. You will also need to apply marine sealant in and around the slotted hole to keep water out.
- Apply marine adhesive sealant to the rubber gasket and underside ofthe Top Down Riser. Secure the Top Down Riser to the surface with your hardware. Be sure to not exceed 20 inch pounds. Use the six provided black nylon shoulder washers for the FTDR500.
OPTIONAL
- You may consider using a Seaview Cable Gland for routing the cables through the mounting surface.
OPTIONAL ACCESSORIES
Call 800-655-7922 or visit www.seaviewglobal.com. for available accessories.
CABLE GLANDS
Seaview Cable Glands provides waterproof cable routing.
- Tel: 800-655-7922
- www.seaviewglobal.com.
- Tel: +33 4 94 53 27 70
- www.seaviewprogress.com.
- 7-08262023
- For Seaview Top Down Risers: FTDR3, FTDR4, FTDR500
- Refer to the website for the most up to date instructions and videos.
- WWW.SEAVIEWGLOBAL.COM.
References
- Seaview | Leaders In Mounting Solutions For Marine Electronics
- Profitez des meilleurs équipements pour votre bateau
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>